The exhaust camshaft VVT sensor (EV1 and EV2 signals) consists of a magnet and MRE (Magnetoresistive Element).
The exhaust camshaft has 3 teeth on its outer circumference. When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE fluctuates. The VVT sensor converts the exhaust camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends the data to the ECM.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0365
P0390 |
No VVT sensor signal is sent to the ECM at an engine speed of 600 rpm or more (1 trip detection logic). | ·
Open or short in VVT sensor for exhaust camshaft circuit ·
VVT sensor for exhaust camshaft ·
Exhaust camshaft ·
Timing chain jumped tooth ·
ECM |
| P0367
P0392 |
Output voltage of VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic). | ·
Open or short in VVT sensor for exhaust camshaft circuit ·
VVT sensor for exhaust camshaft ·
Exhaust camshaft ·
Timing chain jumped tooth ·
ECM |
| P0368
P0393 |
Output voltage of VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic). | ·
Open or short in VVT sensor for exhaust camshaft circuit ·
VVT sensor for exhaust camshaft ·
Exhaust camshaft ·
Timing chain jumped tooth ·
ECM |
Reference: Inspection using an oscilloscope
| Tester Connection | Tool Setting | Condition | Specified Condition |
|---|---|---|---|
| C46-110 (NE+) - C46-111 (NE-) | 5 V/DIV.
20 msec./DIV. |
Cranking or idling | The correct waveform is as shown |
| C46-69 (EV1+) - C46-68 (EV1-) | 5 V/DIV.
20 msec./DIV. |
Cranking or idling | The correct waveform is as shown |
| C46-64 (EV2+) - C46-65 (EV2-) | 5 V/DIV.
20 msec./DIV. |
Cranking or idling | The correct waveform is as shown |
| Tester Connection | Tool Setting | Condition | Specified Condition |
|---|---|---|---|
| C45-110 (NE+) - C45-111 (NE-) | 5 V/DIV.
20 msec./DIV. |
Cranking or idling | The correct waveform is as shown |
| C45-69 (EV1+) - C45-68 (EV1-) | 5 V/DIV.
20 msec./DIV. |
Cranking or idling | The correct waveform is as shown |
| C45-64 (EV2+) - C45-65 (EV2-) | 5 V/DIV.
20 msec./DIV. |
Cranking or idling | The correct waveform is as shown |
EV1 and EV2 are the VVT sensor signals, and NE is the crankshaft position sensor signal.
If no signal is transmitted by the VVT sensor despite the engine running, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.
Also, when the sensor output voltage remains at below 0.3 V, or higher than 4.7 V for more than 4 seconds, the ECM stores a DTC.
Start the engine and run it at idle for 10 seconds or more.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Disconnect the VVT sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (VC2) - Body ground | Engine switch on (IG) | 4.5 to 5.0 V |
| *a | Front view of wire harness connector
(to VVT Sensor) |
| *b | Bank 1 |
| *c | Bank 2 |
OK
NG
Disconnect the VVT sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C121-1 (EX+) - C46-69 (EV1+) | Always | Below 1 Ω |
| C121-2 (EX-) - C46-68 (EV1-) | Always | Below 1 Ω |
| C122-1 (EX+) - C46-64 (EV2+) | Always | Below 1 Ω |
| C122-2 (EX-) - C46-65 (EV2-) | Always | Below 1 Ω |
| C121-1 (EX+) or C46-69 (EV1+) - Body ground | Always | 10 kΩ or higher |
| C121-2 (EX-) or C46-68 (EV1-) - Body ground | Always | 10 kΩ or higher |
| C122-1 (EX+) or C46-64 (EV2+) - Body ground | Always | 10 kΩ or higher |
| C122-2 (EX-) or C46-65 (EV2-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C121-1 (EX+) - C45-69 (EV1+) | Always | Below 1 Ω |
| C121-2 (EX-) - C45-68 (EV1-) | Always | Below 1 Ω |
| C122-1 (EX+) - C45-64 (EV2+) | Always | Below 1 Ω |
| C122-2 (EX-) - C45-65 (EV2-) | Always | Below 1 Ω |
| C121-1 (EX+) or C45-69 (EV1+) - Body ground | Always | 10 kΩ or higher |
| C121-2 (EX-) or C45-68 (EV1-) - Body ground | Always | 10 kΩ or higher |
| C122-1 (EX+) or C45-64 (EV2+) - Body ground | Always | 10 kΩ or higher |
| C122-2 (EX-) or C45-65 (EV2-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Check the VVT sensor installation.
Sensor is installed correctly.
OK
NG
Check the teeth of the camshaft.
Teeth do not have any cracks or deformation.
OK
NG
Replace the VVT sensor (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear DTCs (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Start the engine and idle it for 10 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read DTCs.
| Display (DTC Output) | Proceed to |
|---|---|
| No DTC is output | A |
| P0365, P0367, P0368, P0390, P0392 or P0393 is output | B |
If the engine does not start, replace the ECM.
A
B