Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.08–2016.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0416  Secondary Air Injection System Switching Valve "B" Circuit Open  P0417  Secondary Air Injection System Switching Valve "B" Circuit Shorted  


DESCRIPTION

The ECM operates the air injection VSV relay (AI VLV) which causes the air switching valve (for bank 2) to operate.

DTC No. DTC Detection Condition Trouble Area
P0416 Open or short in the air injection VSV relay (AI VLV) circuit for 3 seconds (1 trip detection logic).
·

Open or short in air injection VSV relay (AI VLV) circuit

·

Air injection VSV relay (AI VLV)

·

ECM


P0417 Open or short in the air injection VSV relay (AI VLV) circuit for 3 seconds (1 trip detection logic).
·

Open or short in air injection VSV relay (AI VLV) circuit

·

Air injection VSV relay (AI VLV)

·

ECM



MONITOR DESCRIPTION

These DTCs are designed to detect a malfunction in the air injection VSV (AI VLV) relay circuit. When the system is normal, the battery voltage is applied to terminal AIR1 of the ECM while the air injection VSV (AI VLV) relay is turned off, and the battery voltage is not applied to terminal AIR1 of the ECM while the air injection VSV (AI VLV) relay is turned on. The ECM illuminates the MIL and stores a DTC when either one of the following conditions is detected.

·

The battery voltage is not applied to terminal AIR1 while the air injection VSV (AI VLV) relay is off.

·

The battery voltage is applied to terminal AIR1 while the air injection VSV (AI VLV) relay is on.


CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the Secondary Air Injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While AIR system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the engine switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the engine switch on (IG).

5.

Turn the GTS on.

6.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

7.

Turn the engine switch off and wait for at least 30 seconds.

8.

Turn the engine switch on (IG) and turn the GTS on.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary air injection check / Automatic Mode.

10.

Start the engine after the GTS initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

Perform the following to confirm the AIR system pending codes: Press ENTER (Exit).

13.

Check for pending DTCs.

OK:

No pending DTC is output.


14.

After "Secondary air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P0416 or P0417.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

Turn the engine switch off.


WIRING DIAGRAM

A351241E02
5.865,1.135 6.167,1.281 0.302,0.146 10 false A38 5.865,3.875 6.229,4.031 0.365,0.156 10 false A38 5.865,1.76 6.188,1.906 0.323,0.146 10 false C45 5.865,5.177 6.146,5.323 0.281,0.146 10 false C45 5.865,4.521 6.146,4.667 0.281,0.146 10 false C45 5.833,0.927 6.156,1.094 0.323,0.167 10 false 34*2 5.854,1.552 6.167,1.708 0.313,0.156 10 false 61*2 5.854,4.302 6.167,4.458 0.313,0.156 10 false 67*2 5.865,3.656 6.177,3.823 0.313,0.167 10 false 53*2 5.854,4.958 6.177,5.125 0.323,0.167 10 false 98*2 6.24,1.104 6.729,1.281 0.49,0.177 10 false MREL 6.24,1.719 6.698,1.896 0.458,0.177 10 false AIR1 6.24,3.823 6.646,4 0.406,0.177 10 false AIP2 6.24,4.479 6.865,4.656 0.625,0.177 10 false VCV1 6.24,5.146 6.646,5.323 0.406,0.177 10 false E2 4.5,3.635 4.781,3.833 0.281,0.198 10 false +BL 4.729,3.844 5.094,4.021 0.365,0.177 10 false AIP2 4.771,4.49 5.094,4.667 0.323,0.177 10 false VC2 4.813,5.156 5.094,5.333 0.281,0.177 10 false E22 4.177,4.958 4.677,5.146 0.5,0.188 10 false GNDL 4.958,1.635 5.094,1.781 0.135,0.146 10 false 2 4.969,2.25 5.104,2.396 0.135,0.146 10 false 3 4.219,1.635 4.354,1.781 0.135,0.146 10 false 1 4.208,2.26 4.344,2.406 0.135,0.146 10 false 5 4.396,2.74 4.969,2.917 0.573,0.177 10 false AI VLV 2.729,1.896 3.448,2.073 0.719,0.177 10 false EFI NO. 2 1.344,1.885 2.094,2.271 0.75,0.385 10 false EFI MAIN NO. 1 3.5,1.771 3.771,1.958 0.271,0.188 10 false 1S 3.51,1.135 3.76,1.323 0.25,0.188 10 false 1S 0.594,1.135 0.854,1.323 0.26,0.188 10 false 1S 3.563,1.531 3.719,1.708 0.156,0.177 10 false 1 3.552,0.906 3.698,1.083 0.146,0.177 10 false 8 0.646,0.906 0.781,1.052 0.135,0.146 10 false 4 0.115,0.094 1.219,0.302 1.104,0.208 10 false for Bank 2: 0.646,4.938 1.25,5.104 0.604,0.167 10 false Battery 6.396,5.667 6.792,5.844 0.396,0.177 10 false ECM 1.823,2.552 3.552,2.76 1.729,0.208 10 false No. 2 Integration Relay 5.135,4.375 5.271,4.521 0.135,0.146 10 false 2 3.99,4.854 4.125,5 0.135,0.146 10 false 1 5.146,3.76 5.281,3.906 0.135,0.146 10 false 3 5.146,5.031 5.281,5.177 0.135,0.146 10 false 4 4.667,3.354 4.802,3.5 0.135,0.146 10 false 5 3.625,5.635 4.031,5.802 0.406,0.167 10 false C138 3.646,5.823 5.552,6.208 1.906,0.385 10 false Air Switching Valve Assembly (for Bank 2) 5.479,1.125 5.781,1.271 0.302,0.146 10 false A52 5.49,3.875 5.854,4.031 0.365,0.156 10 false A52 5.479,1.76 5.802,1.906 0.323,0.146 10 false C46 5.49,5.177 5.771,5.323 0.281,0.146 10 false C46 5.479,4.531 5.76,4.677 0.281,0.146 10 false C46 5.448,0.927 5.771,1.094 0.323,0.167 10 false 34*1 5.469,1.563 5.781,1.719 0.313,0.156 10 false 61*1 5.479,4.302 5.792,4.458 0.313,0.156 10 false 67*1 5.479,3.656 5.792,3.823 0.313,0.167 10 false 53*1 5.479,4.958 5.802,5.125 0.323,0.167 10 false 98*1 1.615,5.875 2.448,6.073 0.833,0.198 10 false *1: for RHD 1.615,6.156 2.448,6.354 0.833,0.198 10 false *2: for LHD 1.969,2.094 3.073,2.479 1.104,0.385 10 false EFI MAIN NO. 1 0.49,3.875 0.885,4.073 0.396,0.198 10 false P/I-B 0.646,1.542 0.771,1.708 0.125,0.167 10 false 1 0.583,1.76 0.844,1.938 0.26,0.177 10 false 1X 0.604,1.927 0.865,2.104 0.26,0.177 10 false *1 0.99,1.552 1.115,1.719 0.125,0.167 10 false 1 0.938,1.76 1.198,1.938 0.26,0.177 10 false 1Y 0.958,1.927 1.219,2.104 0.26,0.177 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT AIR INJECTION VSV RELAY (AI VLV)
a.

Inspect the air injection VSV relay (AI VLV) (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

2.CHECK AIR INJECTION VSV RELAY (AI VLV) (POWER SOURCE)

NG

REPLACE AIR INJECTION VSV RELAY (AI VLV)

2.CHECK AIR INJECTION VSV RELAY (AI VLV) (POWER SOURCE)
a.

Remove the air injection VSV relay (AI VLV).


b.
A372426E01
0.12,0 0.422,0.205 0.302,0.205 10 *a 2.544,2.373 2.845,2.578 0.302,0.205 10 *1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Air injection VSV relay (AI VLV) terminal 1 - Body ground Engine switch on (IG) 11 to 14 V
Air injection VSV relay (AI VLV) terminal 5 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Engine Room Relay Block
*1 Air Injection VSV Relay (AI VLV)


c.

Reinstall the air injection VSV relay (AI VLV).



OK

3.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION VSV RELAY (AI VLV))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION VSV RELAY (AI VLV))
a.

Remove the air injection VSV relay (AI VLV).


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
Air injection VSV relay (AI VLV) terminal 2 - C46-61 (AIR1) Always Below 1 Ω
Air injection VSV relay (AI VLV) terminal 2 or C46-61 (AIR1) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
Air injection VSV relay (AI VLV) terminal 2 - C45-61 (AIR1) Always Below 1 Ω
Air injection VSV relay (AI VLV) terminal 2 or C45-61 (AIR1) - Body ground Always 10 kΩ or higher



d.

Reinstall the air injection VSV relay (AI VLV).


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR