Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil, closing the contacts of the integration relay (EFI MAIN relay) and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A263478E01
2.275,4.563 3.495,4.738 1.221,0.174 10 Integration Relay 2.19,3.601 2.837,3.776 0.647,0.174 10 EFI MAIN 3.47,4.157 3.783,4.332 0.313,0.174 10 EFI 1.431,0.875 1.837,1.040 0.406,0.165 10 AM2 2.111,1.248 4.427,1.443 2.316,0.195 10 Ignition or Starter Switch Assembly*2 5.348,1.242 6.559,1.425 1.211,0.184 10 Main Body ECU*1 6.2,5.005 6.569,5.179 0.369,0.174 10 ECM 1.49,2.249 1.747,2.388 0.257,0.139 10 1C 1.553,2.033 1.672,2.235 0.119,0.202 10 1 1.491,3.848 1.684,4.022 0.193,0.174 10 1B 4.13,3.847 4.323,4.022 0.193,0.174 10 1B 4.12,3.463 4.313,3.637 0.193,0.174 10 1B 4.13,3.003 4.339,3.157 0.209,0.154 10 1B 4.128,2.248 4.337,2.401 0.209,0.154 10 1B 4.12,2.628 4.330,2.781 0.209,0.154 10 1B 4.158,2.039 4.291,2.208 0.133,0.170 10 8 4.169,3.3 4.302,3.470 0.133,0.170 10 4 1.542,3.685 1.702,3.846 0.161,0.161 10 3 4.173,2.464 4.333,2.625 0.161,0.161 10 6 4.169,3.68 4.278,3.854 0.109,0.173 10 2 4.18,2.834 4.289,3.007 0.109,0.173 10 7 4.91,2.389 5.215,2.582 0.305,0.193 10 IGN 5.499,2.241 5.807,2.411 0.309,0.170 10 A38 5.508,3.459 5.817,3.629 0.309,0.170 10 A38 5.505,3.842 5.814,4.011 0.309,0.170 10 A38 5.496,4.377 5.788,4.564 0.291,0.187 10 C45 5.815,2.16 6.298,2.321 0.483,0.162 10 IGSW 5.532,2.069 5.735,2.234 0.202,0.165 10 28 5.573,3.288 5.682,3.444 0.110,0.156 10 2 5.54,3.677 5.742,3.847 0.202,0.170 10 44 5.549,4.219 5.769,4.393 0.221,0.174 10 81 5.843,3.452 6.048,3.634 0.205,0.182 10 +B 5.824,3.826 6.291,4.003 0.468,0.178 10 MREL 5.848,4.374 6.040,4.535 0.192,0.161 10 E1 0.789,4.956 2.709,5.139 1.920,0.184 10 *1: w/ Entry and Start System 0.795,5.313 2.763,5.490 1.968,0.177 10 *2: w/o Entry and Start System 5.348,1.105 5.593,1.261 0.245,0.156 10 E2 5.427,0.753 5.786,0.927 0.360,0.174 10 IG2D 5.156,0.637 5.344,0.811 0.188,0.174 10 11 1.99,0.654 2.109,0.847 0.119,0.193 10 5 3.04,0.645 3.173,0.857 0.133,0.211 10 6 2.12,1.103 2.443,1.259 0.323,0.156 10 E93 3.493,2.92 3.742,3.116 0.248,0.196 10 IG2 2.237,2.42 2.884,2.594 0.647,0.174 10 IG2 MAIN 0.157,0.129 0.882,0.341 0.725,0.211 12 for LHD: 0.61,4.225 1.108,4.399 0.498,0.174 10 Battery 2.746,0.875 2.995,1.023 0.248,0.148 10 IG2 2.176,0.875 2.499,1.032 0.323,0.158 10 AM2

A263478E03
2.275,4.563 3.495,4.738 1.221,0.174 10 Integration Relay 2.19,3.601 2.837,3.776 0.647,0.174 10 EFI MAIN 3.47,4.157 3.783,4.332 0.313,0.174 10 EFI 1.431,0.875 1.837,1.040 0.406,0.165 10 AM2 2.111,1.248 4.427,1.443 2.316,0.195 10 Ignition or Starter Switch Assembly*2 5.348,1.242 6.559,1.425 1.211,0.184 10 Main Body ECU*1 6.2,5.005 6.569,5.179 0.369,0.174 10 ECM 1.49,2.249 1.747,2.388 0.257,0.139 10 1C 1.553,2.033 1.672,2.235 0.119,0.202 10 1 1.491,3.848 1.684,4.022 0.193,0.174 10 1B 4.13,3.847 4.323,4.022 0.193,0.174 10 1B 4.12,3.463 4.313,3.637 0.193,0.174 10 1B 4.13,3.003 4.339,3.157 0.209,0.154 10 1B 4.128,2.248 4.337,2.401 0.209,0.154 10 1B 4.12,2.628 4.330,2.781 0.209,0.154 10 1B 4.158,2.039 4.291,2.208 0.133,0.170 10 8 4.169,3.3 4.302,3.470 0.133,0.170 10 4 1.542,3.685 1.702,3.846 0.161,0.161 10 3 4.173,2.464 4.333,2.625 0.161,0.161 10 6 4.169,3.68 4.278,3.854 0.109,0.173 10 2 4.18,2.834 4.289,3.007 0.109,0.173 10 7 4.91,2.389 5.215,2.582 0.305,0.193 10 IGN 5.499,2.241 5.807,2.411 0.309,0.170 10 A52 5.508,3.459 5.817,3.629 0.309,0.170 10 A52 5.505,3.842 5.814,4.011 0.309,0.170 10 A52 5.496,4.377 5.788,4.564 0.291,0.187 10 C46 5.815,2.16 6.298,2.321 0.483,0.162 10 IGSW 5.532,2.069 5.735,2.234 0.202,0.165 10 28 5.573,3.288 5.682,3.444 0.110,0.156 10 2 5.54,3.677 5.742,3.847 0.202,0.170 10 44 5.549,4.219 5.769,4.393 0.221,0.174 10 81 5.843,3.452 6.048,3.634 0.205,0.182 10 +B 5.824,3.826 6.291,4.003 0.468,0.178 10 MREL 5.848,4.374 6.040,4.535 0.192,0.161 10 E1 0.789,4.956 2.709,5.139 1.920,0.184 10 *1: w/ Entry and Start System 0.795,5.313 2.763,5.490 1.968,0.177 10 *2: w/o Entry and Start System 5.348,1.105 5.593,1.261 0.245,0.156 10 E2 5.427,0.753 5.786,0.927 0.360,0.174 10 IG2D 5.156,0.637 5.344,0.811 0.188,0.174 10 11 1.99,0.654 2.109,0.847 0.119,0.193 10 5 3.04,0.645 3.173,0.857 0.133,0.211 10 6 2.12,1.103 2.443,1.259 0.323,0.156 10 E93 3.493,2.92 3.742,3.116 0.248,0.196 10 IG2 2.237,2.42 2.884,2.594 0.647,0.174 10 IG2 MAIN 0.157,0.129 0.882,0.341 0.725,0.211 12 for RHD: 0.61,4.225 1.108,4.399 0.498,0.174 10 Battery 2.164,0.88 2.505,1.023 0.341,0.143 10 AM2 2.737,0.87 2.985,1.023 0.248,0.153 10 IG2

PROCEDURE

1.INSPECT INTEGRATION NO.1 RELAY (INTEGRATION RELAY - BODY GROUND)
U162873E01
2.761,0.841 3.024,0.996 0.263,0.156 10 1C 2.835,1.44 2.987,1.596 0.152,0.156 8 1 2.1,1.995 3.184,2.183 1.084,0.188 10 Integration Relay 0.126,0.035 2.476,0.379 2.350,0.344 10 Front view of wire harness connector: (to Engine Room Relay Block) 1.541,2.696 2.066,2.108 false 1.77,0.841 2.033,0.996 0.263,0.156 10 1B 1.602,1.696 1.77,1.508 false 2.26,1.711 2.147,1.497 false 2.262,1.711 2.363,1.867 0.101,0.156 10 7 1.532,1.709 1.638,1.864 0.106,0.156 10 3

a.

Remove the integration relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1C-1 - Body ground Always 11 to 14 V



c.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-3 - Body ground Always Below 1 Ω
1B-7 - Body ground Always Below 1 Ω



d.

Reinstall the integration relay.



OK

2.INSPECT INTEGRATION NO.1 RELAY (EFI RELAY AND IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INTEGRATION NO.1 RELAY (EFI RELAY AND IG2 RELAY)
A384777E01
0.323,3.094 0.719,3.365 0.396,0.271 1.135,3.083 1.531,3.354 0.396,0.271 2.292,3.073 2.688,3.344 0.396,0.271 1.094,1.792 1.479,1.156 false 1.583,1.781 1.802,1.458 false 0.146,0.125 2.573,0.5 2.427,0.375 10 false Component without harness connected: (Integration Relay) 0.229,0.802 0.979,1.031 0.75,0.229 10 false Fuse Side: 1.542,1.052 2.292,1.281 0.75,0.229 10 false IG2 MAIN 1.854,1.375 2.604,1.604 0.75,0.229 10 false EFI MAIN 0.188,2.573 1.344,2.771 1.156,0.198 10 false Connector Side: 0.417,3.146 0.677,3.344 0.26,0.198 10 false 1C 1.26,3.135 1.521,3.333 0.26,0.198 10 false 1B 2.396,3.125 2.656,3.323 0.26,0.198 10 false 1A

a.

Remove the integration relay from the engine room relay block.


b.

Inspect the EFI MAIN fuse and the IG2 MAIN fuse.

i.

Remove the EFI MAIN fuse and IG2 MAIN fuse from the integration relay.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN fuse Always Below 1 Ω
IG2 MAIN fuse Always Below 1 Ω




c.

Inspect the EFI relay and the IG2 relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-4 Battery voltage not applied to terminals 1B-2 and 1B-3 10 kΩ or higher
Battery voltage applied to terminals 1B-2 and 1B-3 Below 1 Ω
1C-1 - 1B-8 Battery voltage not applied to terminals 1B-7 and 1B-6 10 kΩ or higher
Battery voltage applied to terminals 1B-7 and 1B-6 Below 1 Ω





OK

3.INSPECT ECM (IGSW VOLTAGE)

NG

REPLACE INTEGRATION RELAY

3.INSPECT ECM (IGSW VOLTAGE)
A384779E01
1.438,0.76 1.854,1.01 0.417,0.25 2.24,0.76 2.656,1.01 0.417,0.25 4.74,0.708 5.156,0.958 0.417,0.25 5.552,0.708 5.969,0.958 0.417,0.25 2.49,1.729 2.865,2.198 true 5.74,1.5 6.26,2.083 true 0.313,0.104 2.615,0.458 2.302,0.354 10 false Front view of wire harness connector: (to ECM) 1.51,0.802 1.833,0.99 0.323,0.188 10 false C45 2.323,0.813 2.646,1 0.323,0.188 10 false C46 1.896,0.698 2.125,0.896 0.229,0.198 10 false *1 2.719,0.698 2.948,0.896 0.229,0.198 10 false *2 2.781,2.229 3.354,2.438 0.573,0.208 10 false 81 (E1) 5.938,2.146 6.74,2.385 0.802,0.24 10 false 28 (IGSW) 4.823,0.75 5.146,0.938 0.323,0.188 10 false A38 5.198,0.625 5.427,0.823 0.229,0.198 10 false *1 5.635,0.75 5.958,0.938 0.323,0.188 10 false A52 6.021,0.646 6.25,0.844 0.229,0.198 10 false *2 0.115,2.063 0.958,2.271 0.844,0.208 10 false *1: for LHD 0.115,2.396 0.958,2.604 0.844,0.208 10 false *2: for RHD

a.

Disconnect the ECM connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A38-28 (IGSW) - C45-81 (E1) Ignition switch ON 11 to 14 V

for RHD
Tester Connection Switch Condition Specified Condition
A52-28 (IGSW) - C46-81 (E1) Ignition switch ON 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)
4.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)
A384778E03
2.458,0.979 2.833,1.198 0.375,0.219 4.844,1.302 5.25,1.563 0.406,0.26 5.573,1.302 5.979,1.563 0.406,0.26 2.344,1.719 2.479,1.521 true 2.573,1.708 2.521,1.521 true 2.74,1.719 2.615,1.521 true 1.885,2.281 1.375,2.115 true 5.26,2.792 5.313,1.969 true 6.125,2.802 5.646,2.365 true 0.938,0.094 3.229,0.5 2.292,0.406 10 false Front view of wire harness connector: (to Engine Room Relay Block) 2.563,1.01 2.833,1.198 0.271,0.188 10 false 1B 2.271,1.708 2.438,1.885 0.167,0.177 10 false 2 2.552,1.719 2.719,1.896 0.167,0.177 10 false 3 2.729,1.708 2.896,1.885 0.167,0.177 10 false 4 0.271,2.01 1.406,2.219 1.135,0.208 10 false Integration Relay 4.198,0.323 6.49,0.729 2.292,0.406 10 false Front view of wire harness connector: (to ECM) 4.917,1.344 5.26,1.531 0.344,0.188 10 false A38 5.656,1.354 6,1.542 0.344,0.188 10 false A52 5.26,1.146 5.5,1.323 0.24,0.177 10 false *1 6.031,1.146 6.271,1.323 0.24,0.177 10 false *2 5,2.844 5.583,3.042 0.583,0.198 10 false 2 (+B) 5.979,2.844 6.792,3.063 0.813,0.219 10 false 44 (MREL) 4.052,3.115 4.865,3.333 0.813,0.219 10 false *1: for LHD 4.052,3.417 4.865,3.635 0.813,0.219 10 false *2: for RHD

a.

Check the harness and the connectors between the integration relay and the ECM.


b.

Remove the integration relay from the engine room relay block.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
A38-44 (MREL) - 1B-2 Always Below 1 Ω
A38-2 (+B) - 1B-4 Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A52-44 (MREL) - 1B-2 Always Below 1 Ω
A52-2 (+B) - 1B-4 Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
A38-44 (MREL) or 1B-2 - Body ground Always 10 kΩ or higher
A38-2 (+B) or 1B-4 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A52-44 (MREL) or 1B-2 - Body ground Always 10 kΩ or higher
A52-2 (+B) or 1B-4 - Body ground Always 10 kΩ or higher



e.

Reconnect the ECM connector.


f.

Reinstall the integration relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)
A384778E04
2.458,0.979 2.833,1.198 0.375,0.219 4.844,1.302 5.25,1.563 0.406,0.26 5.573,1.302 5.979,1.563 0.406,0.26 3.042,1.719 2.917,1.521 true 1.885,2.281 1.375,2.115 true 6.125,2.802 5.844,2.104 true 0.938,0.094 3.229,0.5 2.292,0.406 10 false Front view of wire harness connector: (to Engine Room Relay Block) 2.563,1.01 2.833,1.198 0.271,0.188 10 false 1B 3.021,1.729 3.188,1.906 0.167,0.177 10 false 8 0.271,2.01 1.406,2.219 1.135,0.208 10 false Integration Relay 4.198,0.323 6.49,0.729 2.292,0.406 10 false Front view of wire harness connector: (to ECM) 4.917,1.344 5.26,1.531 0.344,0.188 10 false A38 5.656,1.354 6,1.542 0.344,0.188 10 false A52 5.26,1.146 5.5,1.323 0.24,0.177 10 false *1 6.031,1.146 6.271,1.323 0.24,0.177 10 false *2 5.979,2.844 6.792,3.063 0.813,0.219 10 false 28 (IGSW) 4.052,3.115 4.865,3.333 0.813,0.219 10 false *1: for LHD 4.052,3.417 4.865,3.635 0.813,0.219 10 false *2: for RHD

a.

Check the harness and the connectors between the integration relay and the ECM.


b.

Remove the integration relay from the engine room relay block.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
A38-28 (IGSW) - 1B-8 Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A52-28 (IGSW) - 1B-8 Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
A38-28 (IGSW) or 1B-8 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A52-28 (IGSW) or 1B-8 - Body ground Always 10 kΩ or higher



e.

Reconnect the ECM connector.


f.

Reinstall the integration relay.


Result
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C


A

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INTEGRATION RELAY)

B

7.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - INTEGRATION RELAY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INTEGRATION RELAY)
A384780E01
1.448,1.167 1.813,1.406 0.365,0.24 4.781,1.031 5.146,1.271 0.365,0.24 0.854,2.594 1.135,2.198 true 4.958,1.792 5.104,1.615 true 4.24,2.333 3.906,2.042 3.906,2.042 3.708,2.042 false 0.271,0.188 2.583,0.552 2.313,0.365 10 false Front view of wire harness connector: (to Main Body ECU) 3.531,0.146 5.844,0.51 2.313,0.365 10 false Front view of wire harness connector: (to Engine Room Relay Block) 1.531,1.208 1.844,1.406 0.313,0.198 10 false E2 0.698,2.646 1.125,2.833 0.427,0.188 10 false IG2D 4.844,1.073 5.156,1.271 0.313,0.198 10 false 1B 4.813,1.729 5.042,1.906 0.229,0.177 10 false 6 2.604,1.969 3.719,2.156 1.115,0.188 10 false Integration Relay

a.

Remove the integration relay from the engine room relay block.


b.

Disconnect the IG2D main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E2-11 (IG2D) - 1B-6 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E2-11 (IG2D) or 1B-6 - Body ground Always 10 kΩ or higher




OK

CHECK ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - INTEGRATION RELAY)
a.

Remove the integration relay from the engine room relay block.


b.

Disconnect the Ignition or Starter Switch Assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E93-6 (IG2) - 1B-6 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E93-6 (IG2) or 1B-6 - Body ground Always 10 kΩ or higher




OK

8.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the Ignition or Starter Switch Assembly (See page Engine / Hybrid System>1VD-FTV (STARTING)>IGNITION SWITCH>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY