Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) U

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  TERMINALS OF ECM  


U163199E01
2.325,0.568 2.480,0.722 0.155,0.153 10 *1 3.1,0.568 3.256,0.722 0.155,0.153 10 *2 0.216,3.035 1.011,3.210 0.795,0.174 10 *1: for LHD 0.216,3.381 1.011,3.555 0.795,0.174 10 *2: for RHD 2.728,0.699 3.019,0.851 0.290,0.152 10 C46 1.966,0.699 2.257,0.851 0.290,0.152 10 C45 5.52,0.568 5.675,0.722 0.155,0.153 10 *1 6.295,0.568 6.450,0.722 0.155,0.153 10 *2 5.923,0.699 6.213,0.851 0.290,0.152 10 A52 5.16,0.699 5.451,0.851 0.290,0.152 10 A38

Measure the voltage according to the value(s) in the table below.

HINT:

The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated.

The result of the checks should be compared with the standard normal voltage for that pair of terminals, which is displayed in the Specified Condition column.

The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38*1-20 (BATT) - C45*1-81 (E1)
A52*2-20 (BATT) - C46*2-81 (E1)
L - BR Battery (for measuring the battery voltage and for the ECM memory) Always 11 to 14 V
A38*1-28 (IGSW) - C45*1-81 (E1)
A52*2-28 (IGSW) - C46*2-81 (E1)
B - BR Ignition switch Ignition switch ON 11 to 14 V
A38*1-2 (+B) - C45*1-81 (E1)
A52*2-2 (+B) - C46*2-81 (E1)
B - BR Power source of ECM Ignition switch ON 11 to 14 V
A38*1-44 (MREL) - C45*1-81 (E1)
A52*2-44 (MREL) - C46*2-81 (E1)
W - BR EFI relay Ignition switch ON 11 to 14 V
10 seconds elapsed after ignition switch turned off 0 to 1.5 V
C45*1-66 (VCPM) - C45*1-75 (E2)
C46*2-66 (VCPM) - C46*2-75 (E2)
L-B - BR Power source of manifold absolute pressure sensor (for PIM) Ignition switch ON 4.5 to 5.5 V
C45*1-70 (VCM) - C45*1-75 (E2)
C46*2-70 (VCM) - C46*2-75 (E2)
L-R - BR Power source of fuel pressure sensor (for PCR1) Ignition switch ON 4.5 to 5.5 V
C45*1-90 (VCEG) - C45*1-87 (EEGL)
C46*2-90 (VCEG) - C46*2-87 (EEGL)
L-R - BR Power source of EGR valve position sensor Ignition switch ON 4.5 to 5.5 V
C45*1-91 (VCVL) - C45*1-92 (EVLU)
C46*2-91 (VCVL) - C46*2-92 (EVLU)
L-R - BR Power source of throttle position sensor Ignition switch ON 4.5 to 5.5 V
C45*1-72 (VG) - C45*1-118 (EVG)
C46*2-72 (VG) - C46*2-118 (EVG)
L-Y - G-W Mass air flow meter Engine warmed up and idling, A/C switch off 0.5 to 3.4 V
C45*1-71 (THA) - C45*1-75 (E2)
C46*2-71 (THA) - C46*2-75 (E2)
Y - BR Intake air temperature sensor (built into mass air flow meter) Engine warmed up and idling, intake air temperature at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
A38*1-53 (VPA) - A38*1-57 (EPA)
A52*2-53 (VPA) - A52*2-57 (EPA)
R - W Accelerator pedal position sensor (for engine control) Ignition switch ON, accelerator pedal fully released 0.6 to 1.0 V
Ignition switch ON, accelerator pedal fully depressed 3.0 to 4.6 V
A38*1-54 (VPA2) - A38*1-58 (EPA2)
A52*2-54 (VPA2) - A52*2-58 (EPA2)
GR - BE Accelerator pedal position sensor (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 1.4 to 1.8 V
Ignition switch ON, accelerator pedal fully depressed 3.7 to 5.0 V
A38*1-55 (VCPA) - A38*1-57 (EPA)
A52*2-55 (VCPA) - A52*2-57 (EPA)
L - W Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
A38*1-56 (VCP2) - A38*1-58 (EPA2)
A52*2-56 (VCP2) - A52*2-58 (EPA2)
V - BE Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
C45*1-74 (THIA) - C45*1-75 (E2)
C46*2-74 (THIA) - C46*2-75 (E2)
W-G - BR Intake air temperature sensor (after turbocharged) Engine warmed up and idling, intake air temperature sensor (after turbocharged) at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C45*1-76 (THW) - C45*1-75 (E2)
C46*2-76 (THW) - C46*2-75 (E2)
G-B - BR Engine coolant temperature sensor Engine warmed up and idling, engine coolant temperature at 60 to 120°C (140 to 248°F) 0.2 to 1.2 V
C45*1-40 (#1) - C45*1-81 (E1) Y - BR Fuel injector Idling Pulse generation
(see waveform 1)
C46*2-40 (#1) - C46*2-81 (E1)
C45*1-39 (#2) - C45*1-81 (E1) B - BR
C46*2-39 (#2) - C46*2-81 (E1)
C45*1-38 (#3) - C45*1-81 (E1) L - BR
C46*2-38 (#3) - C46*2-81 (E1)
C45*1-37 (#4) - C45*1-81 (E1) R - BR
C46*2-37 (#4) - C46*2-81 (E1)
C45*1-36 (#5) - C45*1-81 (E1) G - BR
C46*2-36 (#5) - C46*2-81 (E1)
C45*1-35 (#6) - C45*1-81 (E1) V - BR
C46*2-35 (#6) - C46*2-81 (E1)
C45*1-34 (#7) - C45*1-81 (E1) W - BR
C46*2-34 (#7) - C46*2-81 (E1)
C45*1-33 (#8) - C45*1-81 (E1) P - BR
C46*2-33 (#8) - C46*2-81 (E1)
C45*1-80 (G+) - C45*1-79 (G-)
C46*2-80 (G+) - C46*2-79 (G-)
W - B Camshaft position sensor Idling Pulse generation
(see waveform)
C45*1-78 (NE+) - C45*1-77 (NE-)
C46*2-78 (NE+) - C46*2-77 (NE-)
B - W Crankshaft position sensor Idling Pulse generation
(see waveform)
C45*1-114 (PIM) - C45*1-75 (E2)
C46*2-114 (PIM) - C46*2-75 (E2)
P-L - BR Manifold absolute pressure sensor Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied 0.1 to 0.7 V
Same as atmospheric pressure 0.8 to 1.4 V
Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied 1.6 to 2.2 V
A38*1-45 (IREL) - C45*1-81 (E1)
A52*2-45 (IREL) - C46*2-81 (E1)
LG - BR EDU relay (EDU 1) Ignition switch off 11 to 14 V
Idling 0 to 1.5 V
A38*1-46 (IRL2) - C45*1-81 (E1)
A52*2-46 (IRL2) - C46*2-81 (E1)
V - BR EDU relay (EDU 2) Ignition switch off 11 to 14 V
Idling 0 to 1.5 V
C45*1-69 (PCR1) - C45*1-75 (E2)
C46*2-69 (PCR1) - C46*2-75 (E2)
B - BR Fuel pressure sensor Idling (Approximately 35 MPa (357 kgf/cm2, 5078 psi)) 1.3 to 1.8 V
C45*1-63 (GREL) - C45*1-81 (E1)
C46*2-63 (GREL) - C46*2-81 (E1)
R-B - BR No. 1 glow relay Cranking 11 to 14 V
Idling 0 to 1.5 V
C45*1-62 (GRL2) - C45*1-81 (E1)
C46*2-62 (GRL2) - C46*2-81 (E1)
R - BR No. 2 glow relay Cranking 11 to 14 V
Idling 0 to 1.5 V
C45*1-116 (THF) - C45*1-75 (E2)
C46*2-116 (THF) - C46*2-75 (E2)
G-R - BR Fuel temperature sensor Ignition switch ON 0.5 to 3.4 V
C45*1-106 (PCV+) - C45*1-105 (PCV-)
C46*2-106 (PCV+) - C46*2-105 (PCV-)
W - BR Suction control valve Idling Pulse generation
(see waveform 2)
C45*1-61 (INJF) - C45*1-81 (E1)
C46*2-61 (INJF) - C46*2-81 (E1)
G - BR No. 1 injector driver Idling Pulse generation
(see waveform 3)
C45*1-60 (INF2) - C45*1-81 (E1)
C46*2-60 (INF2) - C46*2-81 (E1)
W - BR No. 2 injector driver Idling Pulse generation
(see waveform 3)
C45*1-93 (VLU) - C45*1-75 (E2)
C46*2-93 (VLU) - C46*2-75 (E2)
L-W - BR Throttle position sensor (for Bank 1) Ignition switch ON
(throttle valve fully opened)
2.8 to 3.8 V
Idling
(throttle valve fully closed)
0.4 to 1.0 V
C45*1-103 (VLU2) - C45*1-75 (E2)
C46*2-103 (VLU2) - C46*2-75 (E2)
L-W - BR Throttle position sensor (for Bank 2) Ignition switch ON
(throttle valve fully opened)
2.8 to 3.8 V
Idling
(throttle valve fully closed)
0.4 to 1.0 V
C45*1-42 (LUSL) - C45*1-81 (E1)
C46*2-42 (LUSL) - C46*2-81 (E1)
B - BR Diesel throttle duty signal (for Bank 1) Engine warmed up, racing engine Pulse generation
(see waveform 4)
C45*1-84 (LUS2) - C45*1-81 (E1)
C46*2-84 (LUS2) - C46*2-81 (E1)
B - BR Diesel throttle duty signal (for Bank 2) Engine warmed up, racing engine Pulse generation
(see waveform 4)
C45*1-89 (EGLS) - C45*1-75 (E2)
C46*2-89 (EGLS) - C46*2-75 (E2)
R-W - BR No. 1 EGR valve position sensor Ignition switch ON 3.0 to 4.6 V
C45*1-88 (EGS2) - C45*1-75 (E2)
C46*2-88 (EGS2) - C46*2-75 (E2)
R-B - BR No. 2 EGR valve position sensor Ignition switch ON 3.0 to 4.6 V
C45*1-107 (EGRS) - C45*1-81 (E1)
C46*2-107 (EGRS) - C46*2-81 (E1)
R - BR No. 1 EGR valve Engine warmed up and idling Pulse generation
(see waveform 5)
C45*1-108 (ERS2) - C45*1-81 (E1)
C46*2-108 (ERS2) - C46*2-81 (E1)
R-W - BR No. 2 EGR valve Engine warmed up and idling Pulse generation
(see waveform 5)
C45*1-49 (VNTO) - C45*1-81 (E1)
C46*2-49 (VNTO) - C46*2-81 (E1)
R-Y - BR Turbo motor driver (for Bank 1) Idling Pulse generation
(see waveform 6)
C45*1-47 (VNO2) - C45*1-81 (E1)
C46*2-47 (VNO2) - C46*2-81 (E1)
R-W - BR Turbo motor driver (for Bank 2) Idling Pulse generation
(see waveform 6)
C45*1-50 (VNTI) - C45*1-81 (E1)
C46*2-50 (VNTI) - C46*2-81 (E1)
R-L - BR Turbo motor driver (for Bank 1) Idling Pulse generation
(see waveform 7)
C45*1-48 (VNI2) - C45*1-81 (E1)
C46*2-48 (VNI2) - C46*2-81 (E1)
BR - BR Turbo motor driver (for Bank 2) Idling Pulse generation
(see waveform 7)
A38*1-36 (STP) - C45*1-81 (E1)
A52*2-36 (STP) - C46*2-81 (E1)
R - BR Stop light switch Ignition switch ON, brake pedal depressed 7.5 to 14 V
Ignition switch ON, brake pedal released 0 to 1.5 V
A38*1-35 (ST1-) - C45*1-81 (E1)
A52*2-35 (ST1-) - C46*2-81 (E1)
P - BR Stop light switch
(opposite to STP)
Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A38*1-15 (TACH) - C45*1-81 (E1)
A52*2-15 (TACH) - C46*2-81 (E1)
W - BR Engine speed Idling Pulse generation
(see waveform 8)
A38*1-8 (SPD) - C45*1-81 (E1)
A52*2-8 (SPD) - C46*2-81 (E1)
V - BR Speed signal from combination meter Ignition switch ON, wheel rotated slowly Pulse generation
(see waveform 9)
A38*1-48 (STA) - C45*1-81 (E1)
A52*2-48 (STA) - C46*2-81 (E1)
R - BR Starter signal Cranking 6.0 V or more
C45*1-1 (ALT) - C45*1-81 (E1)
C46*2-1 (ALT) - C46*2-81 (E1)
R - BR Generator duty ratio Idling Pulse generation
A38*1-27 (TC) - C45*1-81 (E1)
A52*2-27 (TC) - C46*2-81 (E1)
V - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
A38*1-24 (W) - C45*1-81 (E1)
A52*2-24 (W) - C46*2-81 (E1)
R - BR MIL MIL illuminated 0 to 3 V
MIL not illuminated 11 to 14 V
A38*1-30 (AC1) - C45*1-81 (E1)
A52*2-30 (AC1) - C46*2-81 (E1)
L - BR A/C signal A/C switch on 0 to 1.5 V
A/C switch off 11 to 14 V
A38*1-18 (ACT) - C45*1-81 (E1)
A52*2-18 (ACT) - C46*2-81 (E1)
G - BR A/C signal Ignition switch ON 11 to 14 V
A/C cut control on 0 to 3 V
A38*1-42 (CLSW) - C45*1-81 (E1)
A52*2-42 (CLSW) - C46*2-81 (E1)
B - BR Clutch start switch Ignition switch ON, clutch pedal fully depressed 0 to 3 V
Ignition switch ON, clutch pedal fully released 11 to 14 V
C45*1-2 (PS) - C45*1-81 (E1)
C46*2-2 (PS) - C46*2-81 (E1)
P - BR Power steering oil pressure switch Steering wheel turned 0 to 3 V
Steering wheel not turned 11 to 14 V
C45*1-32 (FSW) - C45*1-81 (E1)
C46*2-32 (FSW) - C46*2-81 (E1)
L*3 - BR Shift position switch Ignition switch ON, shift lever in 1 11 to 14 V
Ignition switch ON, shift lever not in 1 0 to 3 V
C45*1-45 (ACM) - C45*1-81 (E1)
C46*2-45 (ACM) - C46*2-81 (E1)
L - BR VSV (for engine mounting) Idling 0 to 1.5 V
A38*1-43 (NSW) - C45*1-81 (E1)
A52*2-43 (NSW) - C46*2-81 (E1)
L - BR Park/neutral position switch Ignition switch ON, shift lever in P or N Below 3 V
Ignition switch ON, shift lever not in P and N 11 to 14 V
A38*1-41 (CANH) - C45*1-81 (E1)
A52*2-41 (CANH) - C46*2-81 (E1)
P - BR CAN communication line Ignition switch ON Pulse generation)
(see waveform 10)
A38*1-49 (CANL) - C45*1-81 (E1)
A52*2-49 (CANL) - C46*2-81 (E1)
B - BR CAN communication line Ignition switch ON Pulse generation)
(see waveform 11)
A38*1-14 (STSW) - C45*1-81 (E1)
A52*2-14 (STSW) - C46*2-81 (E1)
R - BR Ignition switch signal Shift lever in P or N, ignition switch pushed 6.0 V or more
A38*1-13 (ACCR) - C45*1-81 (E1)
A52*1-13 (ACCR) - C45*1-81 (E1)
L-Y - BR ACC (Accessory) relay control signal Cranking Below 1.5 V
C45*1-51 (STAR) - C45*1-81 (E1)
C46*2-51 (STAR) - C46*2-81 (E1)
L - BR Starter relay control Ignition switch ON Below 1.5 V
Cranking 6.0 V or more
C45*1-43 (FC) - C45*1-81 (E1)
C46*2-43 (FC) - C46*2-81 (E1)
L-B - BR Sub pump relay Relay on 0 to 1.5 V
Relay off 7.5 to 14 V

HINT:
·

*1: for LHD

·

*2: for RHD

·

*3: for M/T



WAVEFORM 1


A009438E24
0.396,0.427 0.604,0.625 0.208,0.198 10 false #1 0.396,0.781 0.635,0.99 0.24,0.208 10 false #2 0.417,1.135 0.646,1.344 0.229,0.208 10 false #7 0.406,1.5 0.625,1.708 0.219,0.208 10 false #3 2.75,0.896 3.302,1.094 0.552,0.198 10 false 5 V/DIV. 1.167,1.979 2.198,2.156 1.031,0.177 10 false 20 msec./DIV.

Fuel Injector No. 1 (to No. 8) Injection Signal
ECM Terminal Name From #1 to #8 and E1
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the injector injection.



WAVEFORM 2


A097624E21
0.229,1.177 0.698,1.375 0.469,0.198 10 false PCV+ 2.781,0.948 3.406,1.146 0.625,0.198 10 false 10 V/DIV. 1.823,1.938 2.802,2.115 0.979,0.177 10 false 5 msec./DIV.

Suction Control Valve Signal
ECM Terminal Name PCV+ and PCV-
Tester Range 10 V/DIV., 5 msec./DIV.
Condition Idling or cranking with warm engine

HINT:

The waveform varies depending on the suction control valve operation.



WAVEFORM 3


A009437E19
0.375,0.865 0.781,1.063 0.406,0.198 10 false INJF 2.74,0.917 3.375,1.125 0.635,0.208 10 false 2 V/DIV. 1.354,1.948 2.302,2.167 0.948,0.219 10 false 20 msec./DIV.

Injector Injection Confirmation Signal
ECM Terminal Name INJF and E1
INF2 and E1
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the injector injection.



WAVEFORM 4


A091225E20
0.313,1.052 0.792,1.25 0.479,0.198 10 false LUSL 2.688,1.021 3.292,1.219 0.604,0.198 10 false 1 V/DIV. 1.552,1.938 2.469,2.104 0.917,0.167 10 false 2 msec./DIV.

Diesel Throttle Motor Signal
ECM Terminal Name LUSL and E1
LUS2 and E1
Tester Range 1 V/DIV., 2 msec./DIV.
Condition Racing with warm engine

HINT:

The waveform varies depending on the throttle valve operation.



WAVEFORM 5


A384421E01
0.302,1.052 0.792,1.229 0.49,0.177 10 false EGRS 2.917,1.042 3.333,1.229 0.417,0.188 10 false GND 2.698,0.354 3.354,0.521 0.656,0.167 10 false 5 V/DIV. 1.479,1.917 2.448,2.083 0.969,0.167 10 false 5 msec./DIV.

EGR Position Sensor Signal
ECM Terminal Name EGRS and E1
ERS2 and E1
Tester Range 5 V/DIV., 5 msec./DIV.
Condition Idling

HINT:

The waveform varies depending on the throttle valve operation.



WAVEFORM 6


A148022E01
2.698,0.205 3.285,0.373 0.587,0.169 10 5 V/DIV. 0.083,0.685 0.526,0.853 0.442,0.169 10 VNTO 1.181,1.841 2.078,2.010 0.897,0.169 10 20 msec./DIV.

Turbo Motor Driver Input Signal
ECM Terminal Name VNTO and E1
VNO2 and E1
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the turbocharger operation.



WAVEFORM 7


A148021E01
0.216,0.664 0.754,0.812 0.538,0.147 10 VNTI 2.683,0.251 3.221,0.398 0.538,0.147 10 5 V/DIV. 1.224,1.873 2.153,2.020 0.929,0.147 10 50 msec./ DIV.

Turbo Motor Driver Output Signal
ECM Terminal Name VNTI and E1
VNI2 and E1
Tester Range 5 V/DIV., 50 msec./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the turbocharger status.



WAVEFORM 8


U162818E02
0.302,0.146 0.885,0.344 0.583,0.198 10 false 5 V/DIV. 0.448,1.167 0.823,1.365 0.375,0.198 10 false GND 2.125,1.875 3.073,2.073 0.948,0.198 10 false 10 msec./DIV.

Engine Speed Signal
ECM Terminal Names TACH and E1
Tester Range 5 V/DIV., 10 msec./DIV.
Conditions Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 9


G037487E23
0.073,1.219 0.469,1.417 0.396,0.198 10 false SPD 2.75,0.365 3.406,0.563 0.656,0.198 10 false 5 V/DIV. 2.885,1.208 3.292,1.406 0.406,0.198 10 false GND 1.313,1.948 2.469,2.146 1.156,0.198 10 false 10 msec./DIV.

Vehicle Speed Signal
ECM Terminal Name SPD and E1
Tester Range 5 V/DIV., 10 msec./DIV.
Condition Driving at vehicle speed of 40 km/h (25 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 10


G036660E25
2.365,0.281 3.01,0.479 0.646,0.198 10 false 1 V/DIV. 2.625,1.375 3.042,1.573 0.417,0.198 10 false GND 1.146,1.885 2.115,2.094 0.969,0.208 10 false 10 msec./DIV

CAN Communication Signal
ECM Terminal Name CAN+ and E1
Tester Range 1 V/DIV., 10 msec./DIV.
Condition Engine stopped, ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 11


G036661E25
2.354,0.229 2.979,0.427 0.625,0.198 10 false 1 V/DIV. 2.594,1.333 3,1.531 0.406,0.198 10 false GND 1.167,1.844 2.094,2.031 0.927,0.188 10 false 10 msec./DIV.

CAN Communication Signal
ECM Terminal Name CAN- and E1
Tester Range 1 V/DIV., 10 msec./DIV.
Condition Engine stopped, ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.