Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) M

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  REGISTRATION  


PROCEDURE

Hide 1. LEARNING VALUES CONFIRMATION

This procedure uses the GTS to save the learned values (injector compensation code) stored in the ECM.

A321530E01
0.03,0.016 1.926,0.221 1.897,0.205 10 Learning Values Confirmation: 2.78,0.226 3.121,0.412 0.341,0.185 10 Start 2.733,1.095 3.167,1.266 0.434,0.171 10 Notice 2.562,1.973 3.306,2.140 0.744,0.167 10 Select Item 2.112,3.337 3.777,3.631 1.665,0.295 10 Confirm Learning Value(s) 2.594,2.697 2.916,2.945 0.323,0.248 10 Next 3,1.394 3.323,1.642 0.323,0.248 10 Next 3,0.553 3.323,0.802 0.323,0.248 10 Next 2.812,4.334 3.089,4.487 0.276,0.153 10 End 3,3.692 3.295,3.963 0.295,0.272 10 Exit 1.641,3.477 1.982,3.753 0.341,0.276 10 Back 5.825,1.416 6.850,1.594 1.025,0.178 10 Retrieving Error 2.057,2.249 3.854,2.448 1.797,0.200 10 Injector Compensation Code 6.344,0.866 6.967,1.115 0.623,0.248 10 Try Again

HINT:
A341121

A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation.


d.
A266977

Press "Next".


e.
A266978

Press "Next" again to proceed.


f.
A320571

Select the value to confirm and press "Next".


g.
A320572

When the next screen is displayed, confirm the contents and press "Exit".


Hide 2. LEARNING VALUES SAVE

This procedure uses the GTS to save the learned values (injector compensation code) stored in the ECM in the GTS depending on the components being replaced.

A209877E13
0.135,0.104 1.781,0.292 1.646,0.188 10 Learning Values Save: 3.24,0.625 3.813,0.844 0.573,0.219 10 Start 3.448,1.042 3.906,1.219 0.458,0.177 10 Next 3.448,1.896 3.927,2.083 0.479,0.188 10 Next 3.177,1.5 3.771,1.677 0.594,0.177 10 Notice 2.479,2.313 4.573,2.51 2.094,0.198 10 Select Replaced Component(s) 2.49,2.75 3.604,2.917 1.115,0.167 10 - Engine ECU 2.49,3.26 3.927,3.458 1.438,0.198 10 - Engine Assembly 2.49,3.781 3.875,3.958 1.385,0.177 10 - Injector Assembly 6.188,2.406 6.854,2.594 0.667,0.188 10 Try Again 5.688,2.885 6.813,3.094 1.125,0.208 10 Retrieving Error 3.052,4.365 3.521,4.573 0.469,0.208 10 Next 2.302,5.042 4.438,5.208 2.135,0.167 10 Learning Value(s) Save Complete 3.458,5.531 3.875,5.719 0.417,0.188 10 Exit 3.26,6.063 3.646,6.24 0.385,0.177 10 End 0.323,6.052 2.042,6.25 1.719,0.198 10 No Learning Value to Save 2.167,6.271 2.521,6.427 0.354,0.156 10 OK 4.896,5.281 5.552,5.458 0.656,0.177 10 Overwrite 5.625,5.083 6.813,5.25 1.188,0.167 10 Confirm Overwrite

HINT:
·

When replacing the engine assembly, fuel injector together with the ECM, this function automatically determines the data which can be transferred (old data) and saves the data in the GTS.

·
A341126

When there is no data to read from the ECM, manually perform the procedure to register each compensation code and learning value in the ECM.

·
A341127

A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values save.


d.
A268095

Press "Next".


e.
A268096

Press "Next" again to proceed.


f.
A321531

Select any components being replaced and press "Next". If no applicable components are displayed, press "Next" without selecting anything.


g.
A341130

If the overwrite confirmation screen is displayed, press "Overwrite".


h.
A268098

When the operation is finished, confirm the date and time of the save operation, and press "Exit".


Hide 3. LEARNING VALUES WRITE

This procedure uses the GTS to write all of the learned values (injector compensation code) stored in the GTS to the ECM.

A202034E25
0.156,0.125 1.646,0.469 1.49,0.344 10 false Learning Values Write: 2.667,0.646 3.094,0.844 0.427,0.198 10 false Start 2.625,1.51 3.063,1.792 0.438,0.281 10 false Notice 2.042,2.313 3.656,2.594 1.615,0.281 10 false Saved Date Confirmation 1.969,3.781 3.708,4.073 1.74,0.292 10 false Following Setting Complete 2.49,2.833 2.813,3.083 0.323,0.25 10 false Yes 2.448,4.219 2.833,4.406 0.385,0.188 10 false Next 2.438,1.896 2.823,2.135 0.385,0.24 10 false Next 2.896,1.052 3.219,1.302 0.323,0.25 10 false Next 5.25,5.323 5.625,5.531 0.375,0.208 10 false Exit 3.896,5.844 4.177,6.125 0.281,0.281 10 false End 2.469,5.302 2.76,5.573 0.292,0.271 10 false Exit 6.188,5.115 6.635,5.323 0.448,0.208 10 false Back 1.469,5.094 1.865,5.344 0.396,0.25 10 false Back 5.302,2.063 6.323,2.385 1.021,0.323 10 false Retrieving Error 5.823,1.594 6.448,1.844 0.625,0.25 10 false Try Again 5.26,2.417 6.385,2.74 1.125,0.323 10 false Writing Code Fail 4.302,1.458 4.99,1.719 0.688,0.26 10 false Data Error 4.365,1.167 4.927,1.427 0.563,0.26 10 false No Data 4.313,4.844 6.125,5.135 1.813,0.292 10 false Execute Following Functions 2.115,4.844 3.573,5.135 1.458,0.292 10 false All Setting(s) Complete

HINT:
A341132

A malfunction may occur when writing the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values write.


d.
A268099

Press "Next".


e.
A268100

Press "Next" again to proceed.


f.
A341135

If the "Error Learning Values Write" screen indicating a problem with the saved value(s) or an absence of saved values is displayed, perform "Learning Values Save" again.


g.
A341136

Confirm the date and time of the save operation, and then press "Yes".


h.

Confirm the contents, and then press "Next".


i.
A321532

If any instructions are displayed on the GTS, manually perform the procedure to register each applicable compensation code or learning value in the ECM.


j.

Clear the DTCs.


Hide 4. AFTER REPLACING INJECTOR(S) WITH NEW ONE(S), INPUT COMPENSATION CODE(S) OF INJECTOR(S) INTO ECM AS FOLLOWS:

NOTICE:
·

When an injector is replaced, the injector's compensation code must be input into the ECM. When the ECM is changed, all of the existing injector compensation codes must be input into the new ECM.

·

Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector. If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.



a.
A085701E06
2.552,1.729 2.729,1.729 2.729,1.729 2.771,1.354 false 0.021,0 0.865,0.219 0.844,0.219 10 false Example: 1.083,1.635 2.552,2.01 1.469,0.375 10 false Injector Compensation Code

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.


HINT:

The injector compensation code is imprinted on the head portion of each injector.



c.
A321636

Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Injector Compensation.


d.

Press Next.


e.
A321637

Press Next again to proceed.


f.
A321638

Select "Set Compensation Code".


g.

Press Next.


h.
A321639

Select the number of the cylinder corresponding to the injector compensation code that you want to read.


i.

Press Next.


j.
A321640

Register compensation code.

i.

Press input.


ii.
A321641

Manually input the cylinder's compensation code using the keyboard on the GTS screen. The code is a 30-digit, alphanumeric value imprinted on the injector's head portion.

HINT:

Each injector compensation code is unique. The correct compensation code must be input into each cylinder selected on the GTS.



iii.

Confirm that the compensation code is correct for the selected cylinder is correct, and then press OK.



k.
A321642

Check that the compensation code displayed on the screen is correct, by comparing it with the 30-digit alphanumeric value on the head portion of the fuel injector.

NOTICE:

If an incorrect injector compensation code was input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.


HINT:

If a wrong compensation code was input or read, return to the input Value screen by pressing input. The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.



l.

Press Next to set the compensation code to the ECM.

HINT:
·

If the setting process fails, the compensation code may be incorrect. Check the compensation code again.

·

If the attempted compensation code is correct, a problem with the wire harness or a bad connection with the DLC3 may cause the failure. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.




m.
A321643

If you want to continue with other compensation code registrations, press Next. To finish the registration, press Cancel.


n.

Turn the GTS OFF and then turn the ignition switch OFF.


o.

Wait for at least 30 seconds.


p.

Turn the ignition switch to ON and then turn the GTS on.


q.

Clear DTC P1601 stored in the ECM using the GTS (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).


Hide 5. WHEN REPLACING ECM WITH NEW ONE, INPUT ALL INJECTOR'S COMPENSATION CODES INTO NEW ECM AS FOLLOWS:

NOTICE:
·

When an injector is replaced, the injector's compensation code must be input into the ECM. When the ECM is changed, all of the existing injector compensation codes must be input into the new ECM.

·

Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector. If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.



HINT:

The following operation is available with ECMs that can transmit the registered injector compensation codes to the GTS.


a.
A085701E06
2.552,1.729 2.729,1.729 2.729,1.729 2.771,1.354 false 0.021,0 0.865,0.219 0.844,0.219 10 false Example: 1.083,1.635 2.552,2.01 1.469,0.375 10 false Injector Compensation Code

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.


HINT:

The injector compensation code is imprinted on the head portion of each injector.



c.
A321636

Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Injector Compensation.


d.

Press Next.


e.
A321637

Press Next again to proceed.


f.
A321644

Select Read Compensation Code.


g.

Press Next.


h.
A321639

Select the number of the cylinder corresponding to the injector compensation code that you want to read.


i.

Press Next.

HINT:

The reading process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and restart this operation.



j.
A321645

Check the injector compensation code (30-digit alphanumeric value) is displayed on the GTS screen.


k.

Press Save.


l.

Check that the compensation code displayed on the GTS screen is correct.

A385043E02
0.688,0.115 3.094,0.49 2.406,0.375 10 false When no injection compensation code for the cylinder exists in the tester: 4.052,0.125 6.656,0.5 2.604,0.375 10 false When another injector compensation code for the cylinder exists in the tester:


m.

Press Save or Replace, save the injector compensation code.

HINT:
·

The existing compensation code is overwritten with the new compensation code and is deleted from the GTS.

·

The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.




n.
A321645

If you want to read and save other injector compensation codes for other cylinders, press Next to continue. To finish this operation, press Cancel.


o.

Turn the ignition switch OFF.


p.

Turn the GTS OFF.


q.

Replace the ECM.


r.
A085701E06
2.552,1.729 2.729,1.729 2.729,1.729 2.771,1.354 false 0.021,0 0.865,0.219 0.844,0.219 10 false Example: 1.083,1.635 2.552,2.01 1.469,0.375 10 false Injector Compensation Code

Connect the GTS to the DLC3.


s.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.


HINT:

The injector compensation code is imprinted on the head portion of each injector.



t.
A321636

Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Injector Compensation.


u.

Press Next.


v.
A321637

Press Next again to proceed.


w.
A321638

Select Set Compensation Code.


x.

Press Next.


y.
A321639

Select the number of the cylinder corresponding to the injector compensation code that you want to read.


z.

Press Next.


aa.
A321642

Check that the compensation code displayed on the screen is correct, by comparing it with the 30-digit alphanumeric value on the head portion of the fuel injector.

NOTICE:

If an incorrect injector compensation code was input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.


HINT:

If a wrong compensation code was input or read, return to the input Value screen by pressing input. The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.



ab.

Press Next to set the compensation code to the ECM.

HINT:
·

If the setting fails, the compensation code may be incorrect. Check the compensation code again.

·

If the attempted compensation code is correct, a problem with the wire harness or a bad connection with the DLC3 may cause the failure. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.




ac.
A321643

If you want to continue with other compensation code registrations, press Next. To finish the registration, press Cancel.


ad.

Turn the GTS OFF and then turn the ignition switch OFF.


ae.

Wait for at least 30 seconds.


af.

Turn the ignition switch to ON and then turn the GTS ON.


ag.

Clear DTC P1601 stored in the ECM using the GTS (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).