Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) U

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  TERMINALS OF ECM  


U163199E01
2.325,0.568 2.480,0.722 0.155,0.153 10 *1 3.1,0.568 3.256,0.722 0.155,0.153 10 *2 0.216,3.035 1.011,3.210 0.795,0.174 10 *1: for LHD 0.216,3.381 1.011,3.555 0.795,0.174 10 *2: for RHD 2.728,0.699 3.019,0.851 0.290,0.152 10 C46 1.966,0.699 2.257,0.851 0.290,0.152 10 C45 5.52,0.568 5.675,0.722 0.155,0.153 10 *1 6.295,0.568 6.450,0.722 0.155,0.153 10 *2 5.923,0.699 6.213,0.851 0.290,0.152 10 A52 5.16,0.699 5.451,0.851 0.290,0.152 10 A38

Measure the voltage according to the value(s) in the table below.

HINT:

The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated.

The result of the checks should be compared with the standard normal voltage for that pair of terminals, which is displayed in the Specified Condition column.

The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38*1-20 (BATT) - C45*1-81 (E1)
A52*2-20 (BATT) - C46*2-81 (E1)
L - BR Battery (for measuring the battery voltage and for the ECM memory) Always 11 to 14 V
A38*1-28 (IGSW) - C45*1-81 (E1)
A52*2-28 (IGSW) - C46*2-81 (E1)
B - BR Engine switch Engine switch on (IG) 11 to 14 V
A38*1-2 (+B) - C45*1-81 (E1)
A52*2-2 (+B) - C46*2-81 (E1)
B - BR Power source of ECM Engine switch on (IG) 11 to 14 V
A38*1-1 (+B2) - C45*1-81 (E1)
A52*2-1 (+B2) - C46*2-81 (E1)
B - BR Power source of ECM Engine switch on (IG) 11 to 14 V
A38*1-44 (MREL) - C45*1-81 (E1)
A52*2-44 (MREL) - C46*2-81 (E1)
W - BR EFI relay Engine switch on (IG) 11 to 14 V
10 seconds elapsed after engine switch turned off 0 to 1.5 V
C45*1-66 (VCPM) - C45*1-92 (E2)
C46*2-66 (VCPM) - C46*2-92 (E2)
L-B - BR Power source of manifold absolute pressure sensor (for PIM) Engine switch on (IG) 4.5 to 5.5 V
C45*1-118 (VCM) - C45*1-95 (E2M)
C46*2-118 (VCM) - C46*2-95 (E2M)
L-R - BR Power source of fuel pressure sensor (for PCR1) Engine switch on (IG) 4.5 to 5.5 V
C45*1-91 (VC) - C45*1-92 (E2)
C46*2-91 (VC) - C46*2-92 (E2)
B - BR Power source of EGR valve position sensor and differential pressure sensor Engine switch on (IG) 4.5 to 5.5 V
C45*1-110 (VCVL) - C45*1-87 (EVLU)
C46*2-110 (VCVL) - C46*2-87 (EVLU)
L-R - BR Power source of throttle position sensor Engine switch on (IG) 4.5 to 5.5 V
C45*1-71 (VG) - C45*1-94 (EVG)
C46*2-71 (VG) - C46*2-94 (EVG)
L-Y - G-W Mass air flow meter Idling Pulse generation
C45*1-115 (THA) - C45*1-92 (E2)
C46*2-115 (THA) - C46*2-92 (E2)
Y - BR Intake air temperature sensor (built into mass air flow meter) Engine warmed up and idling, intake air temperature at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
A38*1-53 (VPA) - A38*1-57 (EPA)
A52*2-53 (VPA) - A52*2-57 (EPA)
R - W Accelerator pedal position sensor (for engine control) Engine switch on (IG), accelerator pedal fully released 0.6 to 1.0 V
Engine switch on (IG), accelerator pedal fully depressed 3.0 to 4.6 V
A38*1-54 (VPA2) - A38*1-58 (EPA2)
A52*2-54 (VPA2) - A52*2-58 (EPA2)
GR - BE Accelerator pedal position sensor (for sensor malfunction detection) Engine switch on (IG), accelerator pedal fully released 1.4 to 1.8 V
Engine switch on (IG), accelerator pedal fully depressed 3.7 to 5.0 V
A38*1-55 (VCPA) - A38*1-57 (EPA)
A52*2-55 (VCPA) - A52*2-57 (EPA)
L - W Power source of accelerator pedal position sensor (for VPA) Engine switch on (IG) 4.5 to 5.5 V
A38*1-56 (VCP2) - A38*1-58 (EPA2)
A52*2-56 (VCP2) - A52*2-58 (EPA2)
V - BE Power source of accelerator pedal position sensor (for VPA2) Engine switch on (IG) 4.5 to 5.5 V
C45*1-90 (THIA) - C45*1-92 (E2)
C46*2-90 (THIA) - C46*2-92 (E2)
W-G - BR Intake air temperature sensor (turbo) Engine warmed up and idling, intake air temperature sensor (after turbocharged) at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C45*1-93 (THW) - C45*1-92 (E2)
C46*2-93 (THW) - C46*2-92 (E2)
G-B - BR Engine coolant temperature sensor Engine warmed up and idling, engine coolant temperature at 60 to 120°C (140 to 248°F) 0.2 to 1.2 V
C45*1-40 (#1) - C45*1-81 (E1)
C46*2-40 (#1) - C46*2-81 (E1)
Y - BR Injector assembly Idling Pulse generation
(see waveform 1)
C45*1-39 (#2) - C45*1-81 (E1)
C46*2-39 (#2) - C46*2-81 (E1)
B - BR
C45*1-38 (#3) - C45*1-81 (E1)
C46*2-38 (#3) - C46*2-81 (E1)
L - BR
C45*1-37 (#4) - C45*1-81 (E1)
C46*2-37 (#4) - C46*2-81 (E1)
R - BR
C45*1-36 (#5) - C45*1-81 (E1)
C46*2-36 (#5) - C46*2-81 (E1)
G - BR
C45*1-35 (#6) - C45*1-81 (E1)
C46*2-35 (#6) - C46*2-81 (E1)
V - BR
C45*1-34 (#7) - C45*1-81 (E1)
C46*2-34 (#7) - C46*2-81 (E1)
W - BR
C45*1-33 (#8) - C45*1-81 (E1)
C46*2-33 (#8) - C46*2-81 (E1)
P - BR
C45*1-80 (G+) - C45*1-79 (G-)
C46*2-80 (G+) - C46*2-79 (G-)
W - B Camshaft position sensor Idling Pulse generation
C45*1-78 (NE+) - C45*1-77 (NE-)
C46*2-78 (NE+) - C46*2-77 (NE-)
B - W Crankshaft position sensor Idling Pulse generation
C45*1-67 (PIM) - C45*1-92 (E2)
C46*2-67 (PIM) - C46*2-92 (E2)
P-L - BR Manifold absolute pressure sensor Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied 0.1 to 0.7 V
Same as atmospheric pressure 0.8 to 1.4 V
Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied 1.6 to 2.2 V
A38*1-45 (IREL) - C45*1-81 (E1)
A52*2-45 (IREL) - C46*2-81 (E1)
LG - BR EDU relay (EDU 1) Engine switch off 11 to 14 V
Idling 0 to 1.5 V
A38*1-46 (IRL2) - C45*1-81 (E1)
A52*2-46 (IRL2) - C46*2-81 (E1)
V - BR EDU relay (EDU 2) Engine switch off 11 to 14 V
Idling 0 to 1.5 V
C45*1-72 (PCR1) - C45*1-95 (E2M)
C46*2-72 (PCR1) - C46*2-95 (E2M)
B - BR Fuel pressure sensor Idling (Approximately 35 MPa (357 kgf/cm2, 5078 psi)) 1.3 to 1.8 V
A38*1-12 (GREL) - C45*1-81 (E1)
A52*2-12 (GREL) - C46*2-81 (E1)
V - BR No. 1 glow relay Cranking 11 to 14 V
Idling 0 to 1.5 V
A38*1-23 (GRL2) - C45*1-81 (E1)
A52*2-23 (GRL2) - C46*2-81 (E1)
LG - BR No. 2 glow relay Cranking 11 to 14 V
Idling 0 to 1.5 V
C45*1-116 (THF) - C45*1-92 (E2)
C46*2-116 (THF) - C46*2-92 (E2)
G-R - BR Fuel temperature sensor Engine switch on (IG) 0.5 to 3.4 V
C45*1-104 (PCV+) - C45*1-105 (PCV-)
C46*2-104 (PCV+) - C46*2-105 (PCV-)
W - BR Suction control valve Idling Pulse generation
(see waveform 2)
C45*1-60 (INJ1) - C45*1-81 (E1)
C46*2-60 (INJ1) - C46*2-81 (E1)
G - BR No. 1 injector driver Idling Pulse generation
(see waveform 3)
C45*1-61 (INJ2) - C45*1-81 (E1)
C46*2-61 (INJ2) - C46*2-81 (E1)
W - BR No. 2 injector driver Idling Pulse generation
(see waveform 3)
C45*1-64 (VLU) - C45*1-87 (EVLU)
C46*2-64 (VLU) - C46*2-87 (EVLU)
L-W - BR Throttle position sensor (for Bank 1) Engine switch on (IG)
(throttle valve fully opened)
2.8 to 3.8 V
Idling
(throttle valve fully closed)
0.4 to 1.0 V
C45*1-65 (VLU2) - C45*1-87 (EVLU)
C46*2-65 (VLU2) - C46*2-87 (EVLU)
L-W - BR Throttle position sensor (for Bank 2) Engine switch on (IG)
(throttle valve fully opened)
2.8 to 3.8 V
Idling
(throttle valve fully closed)
0.4 to 1.0 V
C45*1-57 (LUSL) - C45*1-81 (E1)
C46*2-57 (LUSL) - C46*2-81 (E1)
B - BR Diesel throttle duty signal (for Bank 1) Engine warmed up, racing engine Pulse generation
(see waveform 4)
C45*1-56 (LUS2) - C45*1-81 (E1)
C46*2-56 (LUS2) - C46*2-81 (E1)
B - BR Diesel throttle duty signal (for Bank 2) Engine warmed up, racing engine Pulse generation
(see waveform 4)
C45*1-88 (EGLS) - C45*1-92 (E2)
C46*2-88 (EGLS) - C46*2-92 (E2)
R-W - BR No. 1 EGR valve position sensor Engine switch on (IG) 3.0 to 4.6 V
C45*1-89 (EGS2) - C45*1-92 (E2)
C46*2-89 (EGS2) - C46*2-92 (E2)
R-B - BR No. 2 EGR valve position sensor Engine switch on (IG) 3.0 to 4.6 V
C45*1-82 (EGRS) - C45*1-81 (E1)
C46*2-82 (EGRS) - C46*2-81 (E1)
R - BR No. 1 EGR valve assembly Engine warmed up and idling Pulse generation
(see waveform 5)
C45*1-42 (ERS2) - C45*1-81 (E1)
C46*2-42 (ERS2) - C46*2-81 (E1)
R-W - BR No. 2 EGR valve assembly Engine warmed up and idling Pulse generation
(see waveform 5)
C45*1-86 (M+) - C45*1-81 (E1)
C46*2-86 (M+) - C46*2-81 (E1)
G - BR DC motor (turbocharger sub-assembly for Bank 1) Idling Pulse generation
(see waveform 6)
C45*1-18 (VN2+) - C45*1-81 (E1)
C46*2-18 (VN2+) - C46*2-81 (E1)
W - BR DC motor (turbocharger sub-assembly for Bank 2) Idling Pulse generation
(see waveform 6)
C45*1-85 (M-) - C45*1-81 (E1)
C46*2-85 (M-) - C46*2-81 (E1)
B - BR DC motor (turbocharger sub-assembly for Bank 1) Idling Pulse generation
(see waveform 7)
C45*1-41 (VN2-) - C45*1-81 (E1)
C46*2-41 (VN2-) - C46*2-81 (E1)
B - BR DC motor (turbocharger sub-assembly for Bank 2) Idling Pulse generation
(see waveform 7)
A38*1-13 (STP) - C45*1-81 (E1)
A52*2-13 (STP) - C46*2-81 (E1)
R - BR Stop light switch Engine switch on (IG), brake pedal depressed 7.5 to 14 V
Engine switch on (IG), brake pedal released 0 to 1.5 V
A38*1-35 (ST1-) - C45*1-81 (E1)
A52*2-35 (ST1-) - C46*2-81 (E1)
P - BR Stop light switch
(opposite to STP)
Engine switch on (IG), brake pedal depressed 0 to 1.5 V
Engine switch on (IG), brake pedal released 7.5 to 14 V
A38*1-15 (TACH) - C45*1-81 (E1)
A52*2-15 (TACH) - C46*2-81 (E1)
W - BR Engine speed Idling Pulse generation
(see waveform 8)
A38*1-8 (SPD) - C45*1-81 (E1)
A52*2-8 (SPD) - C46*2-81 (E1)
V - BR Speed signal from combination meter Engine switch on (IG), wheel rotated slowly Pulse generation
(see waveform 9)
A38*1-48 (STA) - C45*1-81 (E1)
A52*2-48 (STA) - C46*2-81 (E1)
R - BR Starter signal Cranking 6.0 V or more
C45*1-53 (ALT) - C45*1-81 (E1)
C46*2-53 (ALT) - C46*2-81 (E1)
R - BR Generator duty ratio Idling Pulse generation
A38*1-27 (TC) - C45*1-81 (E1)
A52*2-27 (TC) - C46*2-81 (E1)
V - BR Terminal TC of DLC3 Engine switch on (IG) 11 to 14 V
A38*1-24 (W) - C45*1-81 (E1)
A52*2-24 (W) - C46*2-81 (E1)
R - BR MIL MIL illuminated 0 to 3 V
MIL not illuminated 11 to 14 V
A38*1-30 (AC1) - C45*1-81 (E1)
A52*2-30 (AC1) - C46*2-81 (E1)
L - BR A/C signal A/C switch on 0 to 1.5 V
A/C switch off 11 to 14 V
A38*1-18 (ACT) - C45*1-81 (E1)
A52*2-18 (ACT) - C46*2-81 (E1)
G - BR A/C signal Engine switch on (IG) 11 to 14 V
A/C cut control on 0 to 3 V
C45*1-55 (PSW) - C45*1-81 (E1)
C46*2-55 (PSW) - C46*2-81 (E1)
P - BR Power steering oil pressure switch Steering wheel turned 0 to 3 V
Steering wheel not turned 11 to 14 V
A38*1-52 (ACM) - C45*1-81 (E1)
A52*2-52 (ACM) - C46*2-81 (E1)
L - BR VSV (for engine mounting) Idling 0 to 1.5 V
C45*1-49 (NSW) - C45*1-81 (E1)
C46*2-49 (NSW) - C46*2-81 (E1)
L - BR Park/neutral position switch Engine switch on (IG), shift lever in P or N Below 3 V
Engine switch on (IG), shift lever not in P and N 11 to 14 V
A38*1-41 (CANH) - C45*1-81 (E1)
A52*2-41 (CANH) - C46*2-81 (E1)
P - BR CAN communication line Engine switch on (IG) Pulse generation
(see waveform 10)
A38*1-49 (CANL) - C45*1-81 (E1)
A52*2-49 (CANL) - C46*2-81 (E1)
B - BR CAN communication line Engine switch on (IG) Pulse generation
(see waveform 11)
A38*1-47 (STSW) - C45*1-81 (E1)
A52*2-47 (STSW) - C46*2-81 (E1)
R - BR Engine switch signal Shift lever in P or N, engine switch pushed 6.0 V or more
A38*1-22 (ACCR) - C45*1-81 (E1)
A52*1-22 (ACCR) - C45*1-81 (E1)
L-Y - BR ACC (Accessory) relay control signal Cranking Below 1.5 V
C45*1-52 (STAR) - C45*1-81 (E1)
C46*2-52 (STAR) - C46*2-81 (E1)
L - BR Starter relay control Engine switch on (IG) Below 1.5 V
Cranking 6.0 V or more
C45*1-54 (PRD) - C45*1-81 (E1)
C46*2-54 (PRD) - C46*2-81 (E1)
Y - BR Pressure discharge valve drive signal Engine warmed up, engine racing Pulse generation (See waveform 12)
C45*1-32 (RLFF) - C45*1-81 (E1)
C46*2-32 (RLFF) - C46*2-81 (E1)
R - BR Pressure discharge valve confirmation signal Engine warmed up, engine racing Pulse generation (See waveform 12)
C45*1-120 (VNVC) - C45*1-97 (VNE2)
C46*2-120 (VNVC) - C46*2-97 (VNE2)
W - R Power source of nozzle vane position sensor Engine switch on (IG) 4.5 to 5.5 V
C45*1-74 (VNA) - C45*1-97 (VNE2)
C46*2-74 (VNA) - C46*2-97 (VNE2)
BR - R Nozzle vane position sensor (for bank 1) Engine switch on (IG) 2.3 to 2.7 V
C45*1-117 (VNA2) - C45*1-97 (VNE2)
C46*2-117 (VNA2) - C46*2-97 (VNE2)
B - R Nozzle vane position sensor (for bank 2) Engine switch on (IG) 2.3 to 2.7 V
C45*1-122 (THCF) - C45*1-99 (ETCF)
C46*2-122 (THCF) - C46*2-99 (ETCF)
L - BR Exhaust gas temperature sensor (B1S1) Engine warmed up, idling 4.6 to 4.9 V
C45*1-121 (THCI) - C45*1-99 (ETCF)
C46*2-121 (THCI) - C46*2-99 (ETCF)
G-Y - BR No. 2 Exhaust gas temperature sensor (B1S2) Engine warmed up, idling 4.6 to 4.9 V
C45*1-123 (THCO) - C45*1-99 (ETCF)
C46*2-123 (THCO) - C46*2-99 (ETCF)
W - BR No. 4 Exhaust gas temperature sensor (B1S3) Engine warmed up, idling 4.6 to 4.9 V
C45*1-68 (TCF2) - C45*1-99 (ETCF)
C46*2-68 (TCF2) - C46*2-99 (ETCF)
G-B - BR Exhaust gas temperature sensor (B2S1) Engine warmed up, idling 4.6 to 4.9 V
C45*1-98 (TCI2) - C45*1-99 (ETCF)
C46*2-98 (TCI2) - C46*2-99 (ETCF)
P-L - BR No. 3 Exhaust gas temperature sensor (B2S2) Engine warmed up, idling 4.6 to 4.9 V
C45*1-124 (TCO2) - C45*1-99 (ETCF)
C46*2-124 (TCO2) - C46*2-99 (ETCF)
P-L - BR No. 4 Exhaust gas temperature sensor (B2S3) Engine warmed up, idling 4.6 to 4.9 V
C45*1-83 (FIV) - C45*1-81 (E1)
C46*2-83 (FIV) - C46*2-81 (E1)
W - BR Exhaust fuel addition injector assembly (for bank 1) Exhaust fuel addition injector assembly (for bank 1) operating Pulse generation
C45*1-84 (FIV2) - C45*1-81 (E1)
C46*2-84 (FIV2) - C46*2-81 (E1)
G - BR Exhaust fuel addition injector assembly (for bank 2) Exhaust fuel addition injector assembly (for bank 2) operating Pulse generation
C45*1-45 (HA1A) - C45*1-44 (E04)
C46*2-45 (HA1A) - C46*2-44 (E04)
L - BR Air fuel ratio sensor heater (for bank 1) Engine switch on (IG) Pulse generation
C45*1-102 (A1A+) - C45*1-44 (E04)
C46*2-102 (A1A+) - C46*2-44 (E04)
G - BR Air fuel ratio sensor (for bank 1) Engine switch on (IG) 2.0 to 2.5 V
C45*1-103 (A1A-) - C45*1-44 (E04)
C46*2-103 (A1A-) - C46*2-44 (E04)
R - BR Air fuel ratio sensor (for bank 1) Engine switch on (IG) 2.0 to 2.5 V
C45*1-46 (HA2A) - C45*1-23 (E05)
C46*2-46 (HA2A) - C46*2-23 (E05)
L - W-B Air fuel ratio sensor heater (for bank 2) Engine switch on (IG) Pulse generation
C45*1-125 (A2A+) - C45*1-23 (E05)
C46*2-125 (A2A+) - C46*2-23 (E05)
G - W-B Air fuel ratio sensor (for bank 2) Engine switch on (IG) 2.0 to 2.5 V
C45*1-126 (A2A-) - C45*1-23 (E05)
C46*2-126 (A2A-) - C46*2-23 (E05)
R - W-B Air fuel ratio sensor (for bank 2) Engine switch on (IG) 2.0 to 2.5 V
C45*1-69 (PEX) - C45*1-92 (E2)
C46*2-69 (PEX) - C46*2-92 (E2)
R - BR Differential pressure sensor (for bank 1) Engine switch on (IG) 0.4 to 4.8 V
C45*1-70 (PEX2) - C45*1-92 (E2)
C46*2-70 (PEX2) - C46*2-92 (E2)
R - BR Differential pressure sensor (for bank 2) Engine switch on (IG) 0.4 to 4.8 V

HINT:
·

*1: for LHD

·

*2: for RHD



WAVEFORM 1


A009438E24
0.396,0.427 0.604,0.625 0.208,0.198 10 false #1 0.396,0.781 0.635,0.99 0.24,0.208 10 false #2 0.417,1.135 0.646,1.344 0.229,0.208 10 false #7 0.406,1.5 0.625,1.708 0.219,0.208 10 false #3 2.75,0.896 3.302,1.094 0.552,0.198 10 false 5 V/DIV. 1.167,1.979 2.198,2.156 1.031,0.177 10 false 20 msec./DIV.

Injector Assembly No. 1 (to No. 8) Injection Signal
ECM Terminal Name From #1 to #8 and E1
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the injector injection.



WAVEFORM 2


A097624E21
0.229,1.177 0.698,1.375 0.469,0.198 10 false PCV+ 2.781,0.948 3.406,1.146 0.625,0.198 10 false 10 V/DIV. 1.823,1.938 2.802,2.115 0.979,0.177 10 false 5 msec./DIV.

Suction Control Valve Signal
ECM Terminal Name PCV+ and PCV-
Tester Range 10 V/DIV., 5 msec./DIV.
Condition Idling or cranking with warm engine

HINT:

The waveform varies depending on the suction control valve operation.



WAVEFORM 3


A009437E13
0.406,0.865 0.813,1.063 0.406,0.198 10 false INJF 2.74,0.938 3.375,1.146 0.635,0.208 10 false 2 V/DIV. 1.448,1.938 3.427,2.177 1.979,0.24 10 true 20 msec./DIV.

Injector Injection Confirmation Signal
ECM Terminal Name INJ1 and E1
INJ2 and E1
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the injector injection.



WAVEFORM 4


A091225E20
0.313,1.052 0.792,1.25 0.479,0.198 10 false LUSL 2.688,1.021 3.292,1.219 0.604,0.198 10 false 1 V/DIV. 1.552,1.938 2.469,2.104 0.917,0.167 10 false 2 msec./DIV.

Diesel Throttle Motor Signal
ECM Terminal Name LUSL and E1
LUS2 and E1
Tester Range 1 V/DIV., 2 msec./DIV.
Condition Racing with warm engine

HINT:

The waveform varies depending on the throttle valve operation.



WAVEFORM 5


A384421E01
0.302,1.052 0.792,1.229 0.49,0.177 10 false EGRS 2.917,1.042 3.333,1.229 0.417,0.188 10 false GND 2.698,0.354 3.354,0.521 0.656,0.167 10 false 5 V/DIV. 1.479,1.917 2.448,2.083 0.969,0.167 10 false 5 msec./DIV.

EGR Position Sensor Signal
ECM Terminal Name EGRS and E1
ERS2 and E1
Tester Range 5 V/DIV., 5 msec./DIV.
Condition Idling

HINT:

The waveform varies depending on the throttle valve operation.



WAVEFORM 6


A148022E03
2.698,0.205 3.280,0.373 0.582,0.169 10 5 V/DIV. 1.181,1.841 2.078,2.010 0.897,0.169 10 20 msec./DIV.

DC Motor Positive Terminal Signal
ECM Terminal Name M+ and E1
VN2+ and E1
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the turbocharger operation.



WAVEFORM 7


A148021E04
2.683,0.251 3.221,0.398 0.538,0.147 10 5 V/DIV. 1.224,1.873 2.153,2.020 0.929,0.147 10 50 msec./ DIV.

DC Motor Negative Terminal Signal
ECM Terminal Name M- and E1
VN2- and E1
Tester Range 5 V/DIV., 50 msec./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the turbocharger status.



WAVEFORM 8


U162818E02
0.302,0.146 0.885,0.344 0.583,0.198 10 false 5 V/DIV. 0.448,1.167 0.823,1.365 0.375,0.198 10 false GND 2.125,1.875 3.073,2.073 0.948,0.198 10 false 10 msec./DIV.

Engine Speed Signal
ECM Terminal Names TACH and E1
Tester Range 5 V/DIV., 10 msec./DIV.
Conditions Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 9


G037487E23
0.073,1.219 0.469,1.417 0.396,0.198 10 false SPD 2.75,0.365 3.406,0.563 0.656,0.198 10 false 5 V/DIV. 2.885,1.208 3.292,1.406 0.406,0.198 10 false GND 1.313,1.948 2.469,2.146 1.156,0.198 10 false 10 msec./DIV.

Vehicle Speed Signal
ECM Terminal Name SPD and E1
Tester Range 5 V/DIV., 10 msec./DIV.
Condition Driving at vehicle speed of 40 km/h (25 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 10


G036660E25
2.365,0.281 3.01,0.479 0.646,0.198 10 false 1 V/DIV. 2.625,1.375 3.042,1.573 0.417,0.198 10 false GND 1.146,1.885 2.115,2.094 0.969,0.208 10 false 10 msec./DIV

CAN Communication Signal
ECM Terminal Name CAN+ and E1
Tester Range 1 V/DIV., 10 msec./DIV.
Condition Engine stopped, engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 11


G036661E25
2.354,0.229 2.979,0.427 0.625,0.198 10 false 1 V/DIV. 2.594,1.333 3,1.531 0.406,0.198 10 false GND 1.167,1.844 2.094,2.031 0.927,0.188 10 false 10 msec./DIV.

CAN Communication Signal
ECM Terminal Name CAN- and E1
Tester Range 1 V/DIV., 10 msec./DIV.
Condition Engine stopped, engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 12


A243948E09
0.24,0.927 0.833,1.167 0.594,0.24 10 false (b) RLFF 0.26,2.167 0.781,2.406 0.521,0.24 10 false (a) PRD 1.573,2.719 2.427,2.958 0.854,0.24 10 false 1 msec./DIV. 2.729,0.344 3.281,0.583 0.552,0.24 10 false 2 V/DIV.

Pressure Discharge Valve Drive Signal and Pressure Discharge Confirmation Signal
ECM Terminal Name (a) PRD and E1
(b) RLFF and E1
Tester Range 2 V/DIV., 1 msec./DIV.
Condition Engine warmed up, engine racing

HINT:

The wavelength becomes shorter as the engine speed increases.