Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

The intake air temperature sensor is built into the mass air flow meter and detects the intake air temperature.

A thermistor built into the sensor changes its resistance value according to the intake air temperature.

The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The intake air temperature sensor is connected to the ECM.

The 5 V power source voltage from the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with the intake air temperature, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability with a cold engine.

A208462E01
1.469,2 1.625,1.76 1.625,1.76 1.771,1.76 false 0.208,0.146 0.906,0.49 0.698,0.344 10 false (Fig. 1) 0.208,0.542 1.313,0.823 1.104,0.281 10 false Resistance kΩ 1.823,1.688 2.656,2.031 0.833,0.344 10 false Acceptable 1.208,4.073 2.521,4.385 1.313,0.313 10 false Temperature °C (°F)

P0112
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Short in the intake air temperature sensor for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM



P0113
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open in the intake air temperature sensor for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM



Related Data List
DTC No. Data List
P0112
P0113
Intake Air

HINT:
·

If DTC P0112 and/or P0113 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power


·

When DTC P0112 or P0113 is stored, check the intake air temperature by entering the following menus: Engine and ECT / Data List / Intake Air.

Reference
Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit



WIRING DIAGRAM

A165735E15
0.58,2.469 0.875,2.625 0.295,0.156 10 C50 0.58,2.628 2.592,2.983 2.012,0.355 10 Intake Air Temperature Sensor (Built into Mass Air Flow Meter) 5.684,2.693 6.581,2.849 0.897,0.156 10 C45*1, C46*2 5.684,2.852 6.039,3.026 0.355,0.174 10 ECM 2.182,1.666 2.415,1.840 0.233,0.174 10 E2 2.457,1.857 2.581,2.032 0.123,0.174 10 5 2.074,1.054 2.414,1.228 0.339,0.174 10 THA 5.54,1.666 5.772,1.840 0.233,0.174 10 E2 5.54,1.054 5.879,1.228 0.339,0.174 10 THA 2.457,1.245 2.581,1.420 0.123,0.174 10 4 5.264,1.857 5.458,2.032 0.194,0.174 10 92 5.217,1.245 5.596,1.420 0.379,0.174 10 115 6.161,0.937 6.287,1.091 0.126,0.154 10 R 6.254,0.652 6.517,0.817 0.262,0.165 10 5 V 3.716,3.085 4.613,3.241 0.897,0.156 10 *1: for LHD 3.716,3.366 4.613,3.522 0.897,0.156 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Data List / Intake Air.


d.

Read the value.

OK:

Same as actual intake air temperature


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (same as actual intake air temperature) C

HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
U162831E01
1.851,3.444 1.646,4.003 false 2.338,4.003 2.563,4.205 0.225,0.202 10 E2 2.46,0.967 2.790,1.169 0.329,0.202 10 THA 1.486,4.003 1.822,4.205 0.337,0.202 10 THA 2.472,1.444 2.860,1.604 0.388,0.160 10 E2 2.102,3.459 2.349,3.992 false 0.795,0.151 1.085,0.414 0.290,0.262 10 *1 2.65,0.151 2.917,0.376 0.267,0.225 10 *2 0.134,2.187 0.436,2.436 0.301,0.248 10 *a 0.318,3.316 0.599,3.479 0.281,0.163 10 C50

Disconnect the mass air flow meter connector.


b.

Connect terminals 4 (THA) and 5 (E2) of the mass air flow meter wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Engine and ECT / Data List / Intake Air.


f.

Read the value.

OK:

140°C (284°F) or higher


Text in Illustration
*1 Mass air flow meter
*2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter)



OK

7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER.

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C50-4 (THA) - C45-115 (THA) Always Below 1 Ω
C50-5 (E2) - C45-92 (E2) Always Below 1 Ω


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C50-4 (THA) - C46-115 (THA) Always Below 1 Ω
C50-5 (E2) - C46-92 (E2) Always Below 1 Ω




OK

9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A378876E04
0.708,0.24 1.021,0.438 0.313,0.198 10 false *1 2.583,0.198 2.896,0.396 0.313,0.198 10 false *2 2.542,1.021 2.938,1.229 0.396,0.208 10 false THA 2.531,1.49 3.01,1.688 0.479,0.198 10 false E2

Disconnect the mass air flow meter connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Engine and ECT / Data List / Intake Air.


e.

Read the value.

OK:

-40°C (-40°F)


Text in Illustration
*1 Mass Air Flow Meter
*2 ECM



OK

10.REPLACE MASS AIR FLOW METER

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C50-4 (THA) or C45-115 (THA) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C50-4 (THA) or C46-115 (THA) - Body ground Always 10 kΩ or higher




OK

6.REPLACE ECM

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER.

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE MASS AIR FLOW METER

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch to ON for 1 second.


d.

Enter the following menus: Engine and ECT / Trouble Codes.


e.

Confirm that the DTC is not output again.



NEXT

END