Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  P0222  Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input  P0223  Throttle / Pedal Position Sensor / Switch "B" Circuit High Input  


DESCRIPTION

The throttle position sensor is mounted on the diesel throttle body assembly and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.

When the throttle valve is fully closed, a voltage of approximately 0.7 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.5 to 4.0 V when the throttle valve is fully opened.

The ECM determines the vehicle driving conditions from the signals input to its VLU terminal. The data is one of the pieces of information used for EGR control, etc.

A261223E07
2.521,2.094 2.854,3.094 false 2.417,2.604 2.219,3.094 false 2.198,0.781 2.396,1.271 false 1.698,0.25 3.271,0.531 1.573,0.281 10 false Throttle Position Sensor 2.906,3.031 3.448,3.229 0.542,0.198 10 false Hall IC 4.375,0.625 4.781,0.833 0.406,0.208 10 false ECM 4.385,1.083 4.677,1.281 0.292,0.198 10 false 5 V 3.438,1.146 3.906,1.323 0.469,0.177 10 false VCVL 3.563,1.781 3.927,1.969 0.365,0.188 10 false VLU 3.458,2.365 3.906,2.573 0.448,0.208 10 false EVLU 3.146,1.146 3.438,1.333 0.292,0.188 10 false VC 3.156,2.365 3.406,2.583 0.25,0.219 10 false E 3.146,1.771 3.51,1.969 0.365,0.198 10 false VTA 1.719,3.021 2.313,3.229 0.594,0.208 10 false Magnet 1.688,0.688 2.271,0.927 0.583,0.24 10 false Magnet

P0122 (Bank 1), P0222 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 3 seconds Throttle position sensor output (VLU, VLU2) is below 0.2 V for 3 seconds.
(1 trip detection logic)
·

Throttle position sensor

·

Open or short in VLU, VLU2 circuit

·

Open in VC circuit

·

ECM



P0123 (Bank 1), P0223 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 3 seconds Throttle position sensor output (VLU, VLU2) is higher than 4.8 V for 3 seconds.
(1 trip detection logic)
·

Throttle position sensor

·

Open in E2 circuit

·

VC and VLU, VLU2 circuits are short-circuited

·

ECM



HINT:

If DTC P0122, P0123, P0222 and/or P0223 is stored, the following symptoms may appear:


- Intake booming noise

- Black smoke

- Lack of power

- Vibration at engine stop

- Turbo overspeed, turbo damage


MONITOR DESCRIPTION

When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

C129051E10
2.302,1.063 1.99,1.229 false 2.302,2.656 1.99,2.823 false 4.917,0.5 4.615,1.031 false 4.615,2.688 4.917,3.219 false 0.094,0.073 2.896,0.271 2.802,0.198 10 false Throttle Position Sensor Output Voltage (V) 2.063,0.552 2.635,0.75 0.573,0.198 10 false Closed 4.979,0.406 6.469,0.604 1.49,0.198 10 false Store P0123 or P0223 4.01,0.552 4.469,0.75 0.458,0.198 10 false Open 2.646,2.729 4.125,2.927 1.479,0.198 10 false Range of Operation 4.979,3.125 6.458,3.323 1.479,0.198 10 false Store P0122 or P0222 2.323,3.406 4.229,3.635 1.906,0.229 10 false Throttle Valve Opening Angle 4.083,3.198 4.313,3.396 0.229,0.198 10 false 70 2.26,3.198 2.396,3.396 0.135,0.198 10 false 0 1.677,2.771 2.031,2.969 0.354,0.198 10 false 0.20 1.969,2.406 2.354,2.604 0.385,0.198 10 false 0.69 1.969,1.375 2.323,1.573 0.354,0.198 10 false 3.49 1.677,1.115 2.042,1.313 0.365,0.198 10 false 4.80 1.969,0.927 2.323,1.125 0.354,0.198 10 false 5.00

WIRING DIAGRAM

A165736E13
2.01,1.135 2.281,1.344 0.271,0.208 10 false VC 1.938,1.469 2.292,1.677 0.354,0.208 10 false VTA 2.031,1.823 2.313,2 0.281,0.177 10 false E2 5.26,1.146 5.688,1.344 0.427,0.198 10 false VCVL 5.26,1.458 5.563,1.656 0.302,0.198 10 false VLU 5.26,1.823 5.74,2.021 0.479,0.198 10 false EVLU 2.385,1.229 2.573,1.417 0.188,0.188 10 false 1 2.385,1.573 2.573,1.76 0.188,0.188 10 false 3 2.385,1.917 2.573,2.104 0.188,0.188 10 false 2 4.875,1.229 5.167,1.417 0.292,0.188 10 false 110 4.958,1.563 5.156,1.74 0.198,0.177 10 false 64 5.26,3.635 5.719,3.833 0.458,0.198 10 false VLU2 4.896,3.719 5.188,3.906 0.292,0.188 10 false 65 4.948,1.917 5.146,2.104 0.198,0.188 10 false 87 1.073,2.135 1.427,2.323 0.354,0.188 10 false C83 1.073,2.323 3.458,2.5 2.385,0.177 10 false Throttle Position Sensor (for Bank 1) 2.01,3.26 2.281,3.458 0.271,0.198 10 false VC 1.865,3.594 2.281,3.792 0.417,0.198 10 false VTA2 2.052,3.958 2.281,4.156 0.229,0.198 10 false E2 2.385,3.375 2.573,3.563 0.188,0.188 10 false 1 2.385,3.719 2.573,3.906 0.188,0.188 10 false 3 2.385,4.063 2.573,4.25 0.188,0.188 10 false 2 1.073,4.302 1.344,4.479 0.271,0.177 10 false C84 1.073,4.49 3.448,4.667 2.375,0.177 10 false Throttle Position Sensor (for Bank 2) 5.552,4.646 6.552,4.875 1,0.229 10 false C45*1, C46*2 5.563,4.823 5.927,5 0.365,0.177 10 false ECM 0.833,4.948 1.833,5.177 1,0.229 10 false *1: for LHD 0.833,5.271 1.833,5.5 1,0.229 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C83-1 (VC) - C45-110 (VCVL) Always Below 1 Ω
C83-3 (VTA) - C45-64 (VLU) Always Below 1 Ω
C83-2 (E2) - C45-87 (EVLU) Always Below 1 Ω
C84-1 (VC) - C45-110 (VCVL) Always Below 1 Ω
C84-3 (VTA2) - C45-65 (VLU2) Always Below 1 Ω
C84-2 (E2) - C45-87 (EVLU) Always Below 1 Ω
C83-1 (VC) or C45-110 (VCVL) - Body ground Always 10 kΩ or higher
C83-3 (VTA) or C45-64 (VLU) - Body ground Always 10 kΩ or higher
C84-1 (VC) or C45-110 (VCVL) - Body ground Always 10 kΩ or higher
C84-3 (VTA2) or C45-65 (VLU2) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C83-1 (VC) - C46-110 (VCVL) Always Below 1 Ω
C83-3 (VTA) - C46-64 (VLU) Always Below 1 Ω
C83-2 (E2) - C46-87 (EVLU) Always Below 1 Ω
C84-1 (VC) - C46-110 (VCVL) Always Below 1 Ω
C84-3 (VTA2) - C46-65 (VLU2) Always Below 1 Ω
C84-2 (E2) - C46-87 (EVLU) Always Below 1 Ω
C83-1 (VC) or C46-110 (VCVL) - Body ground Always 10 kΩ or higher
C83-3 (VTA) or C46-64 (VLU) - Body ground Always 10 kΩ or higher
C84-1 (VC) or C46-110 (VCVL) - Body ground Always 10 kΩ or higher
C84-3 (VTA2) or C46-65 (VLU2) - Body ground Always 10 kΩ or higher



d.

Reconnect the throttle position sensor connector.


e.

Reconnect the ECM connector.



OK

2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
a.
U164484E01
0.346,0.808 0.623,0.985 0.278,0.177 10 C83 1.098,1.57 1.335,1.724 0.237,0.154 10 VC 0.093,0.058 0.311,0.213 0.218,0.154 10 *a 2.036,1.587 2.264,1.741 0.228,0.154 10 E2 1.772,1.241 2.043,1.57 false 0.346,1.255 0.623,1.431 0.278,0.177 10 C84 0.793,0.802 1.011,0.956 0.218,0.154 10 *A 0.793,1.279 1.011,1.433 0.218,0.154 10 *B

Disconnect the throttle position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C83-1 (VC) - C83-2 (E2) Engine switch on (IG) 4.5 to 5.5 V
C84-1 (VC) - C84-2 (E2) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*A for Bank 1
*B for Bank 2
*a Front view of wire harness connector
(to Throttle Position Sensor)


c.

Reconnect the throttle position sensor connector.



OK

3.REPLACE DIESEL THROTTLE BODY ASSEMBLY

NG

5.REPLACE ECM
3.REPLACE DIESEL THROTTLE BODY ASSEMBLY

When DTC P0122 or P0123 is output:

·

Replace the diesel throttle body assembly (for bank 1) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL).


When DTC P0222 or P0223 is output:

·

Replace the diesel throttle body assembly (for bank 2) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL).



NEXT

4.READ VALUE USING GTS
4.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Enter the following menus: Engine and ECT / Data List / Actual Throttle position, Actual Throttle position #2.


e.

Check the movement of the throttle valve when idling the engine after starting it from engine switch on (IG).

OK:
Condition GTS Display
Engine switch on (IG) 95 to 105%
Idling 5 to 15%




OK

END

NG

5.REPLACE ECM
5.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off.


d.

Turn the engine switch on (IG) for 3 seconds.


e.

Enter the following menus: Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END