Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



P0504
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Depress and release brake pedal with engine switch on (IG) Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Engine switch on (IG).
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off, or the STP signal is on when the ST1- signal is on.
·

Open or short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch

·

ECM



Related Data List
DTC No. Data List
P0504 Stop Light Switch

WIRING DIAGRAM

A160611E24
1.167,0.885 2.24,1.094 1.073,0.208 10 false from IG2 Relay 1.354,1.865 2.24,2.073 0.885,0.208 10 false from Battery 2.792,0.708 3.104,0.865 0.313,0.156 10 false IGN 2.76,1.042 2.896,1.198 0.135,0.156 10 false 1 3.01,1.042 3.146,1.198 0.135,0.156 10 false 2 2.76,2.021 2.896,2.177 0.135,0.156 10 false 1 4.563,1.802 4.698,1.958 0.135,0.156 10 false 1 5.719,3.125 6.104,3.281 0.385,0.156 10 false ECM 3.01,2.021 3.146,2.177 0.135,0.156 10 false 2 3.438,1.802 3.573,1.958 0.135,0.156 10 false 2 4.563,0.813 4.698,0.969 0.135,0.156 10 false 3 5.313,0.802 5.531,0.958 0.219,0.156 10 false 35 5.292,1.781 5.51,1.948 0.219,0.167 10 false 13 5.615,0.813 5.958,0.969 0.344,0.156 10 false ST1- 5.615,1.792 5.958,1.948 0.344,0.156 10 false STP 3.438,0.813 3.573,0.969 0.135,0.156 10 false 4 2.74,1.708 3.146,1.865 0.406,0.156 10 false STOP 3.458,2.375 4.594,2.563 1.135,0.188 10 false Stop Light Switch 5.719,2.958 6.792,3.135 1.073,0.177 10 false A38*1, A52*2 3.469,2.208 3.792,2.406 0.323,0.198 10 false A30 0.573,2.802 1.323,2.99 0.75,0.188 10 false *1: for LHD 0.573,3.135 1.323,3.323 0.75,0.188 10 false *2: for RHD

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the engine switch on (IG).

(c)

Turn the GTS on.

(d)

Enter the following menus: Engine and ECT / Data List / Stop Light Switch.

(e)

Check Stop Light Switch when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed ON
Released OFF

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
a.
U163298E01
0.146,0.064 0.344,0.252 0.198,0.188 10 *a 0.642,0.728 0.938,0.894 0.296,0.166 10 A30

Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A30-2 - Body ground Always 11 to 14 V
A30-4 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch)


c.

Reconnect the stop light switch connector.



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

4.REPLACE STOP LIGHT SWITCH ASSEMBLY
3.CHECK ECM (STP AND ST1- VOLTAGE)
U163701E02
1.771,3.667 2.146,4.292 false 1.771,3.354 2.521,2.708 false 0.521,0.333 0.719,0.531 0.198,0.198 10 false *a 2.208,0.333 2.406,0.531 0.198,0.198 10 false *b 1.573,2.229 1.771,2.427 0.198,0.198 10 false *c 0.24,3.063 0.594,3.24 0.354,0.177 10 false A38 2.563,2.594 3.208,2.771 0.646,0.177 10 false 13 (STP) 2.125,4.302 2.802,4.479 0.677,0.177 10 false 35 (ST1-) 0.24,3.813 0.573,3.99 0.333,0.177 10 false A52 0.323,3.323 0.521,3.521 0.198,0.198 10 false *A 0.344,4.104 0.542,4.302 0.198,0.198 10 false *B

a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Brake Pedal Condition Specified Condition
A38-35 (ST1-) - Body ground Released 11 to 14 V
Depressed 0 to 3 V
A38-13 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V


Standard Voltage:
for RHD
Tester Connection Brake Pedal Condition Specified Condition
A52-35 (ST1-) - Body ground Released 11 to 14 V
Depressed 0 to 3 V
A52-13 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V


Text in Illustration
*A for LHD
*B for RHD
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(ECM)


d.

Reconnect the ECM connector.



OK

5.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE STOP LIGHT SWITCH ASSEMBLY
a.

Replace the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Depress and release the brake pedal.


f.

Enter the following menus: Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.



NEXT

END