The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the ECM memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Ignition switch ON for 3 seconds | The voltage at terminal BATT drops excessively for 3 seconds and part of the stored values in the ECM are initialized.
(1 trip detection logic) |
·
Open in backup power source circuit (to BATT terminal) ·
Battery ·
Battery terminals ·
EFI MAIN fuse ·
ECM |
| DTC No. | Data List |
|---|---|
| P0560 | Battery Voltage* |
*: This is not the voltage at terminal BATT; it is the power supply voltage for the ECM.
If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
When the ignition switch is turned to ON, even though +B voltage is present, when the voltage at terminal BATT (power supply for maintaining memorized values in the ECM) drops excessively, this DTC is stored.
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-20 (BATT) - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A52-20 (BATT) - Body ground | Always | 11 to 14 V |
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector
(ECM) |
Reconnect the ECM connector.
OK
NG
Check that the battery is not depleted (See page Power Source / Network>1VD-FTV (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION).
Battery is not depleted.
OK
NG
Check that the battery terminals are not loose or corroded.
Battery terminals are not loose or corroded.
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON for 3 seconds.
Enter the following menus: Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0560 is output | A |
| No DTC is output | B |
A
B
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Recharge or replace the battery.
NEXT
Repair or replace the battery terminal.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON for 3 seconds.
Enter the following menus: Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT