Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.

P0617
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.5 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
·

Starter relay (ST) circuit

·

Park/neutral position switch assembly

·

ECM



Related Data List
DTC No. Data List
P0617 Starter Signal

WIRING DIAGRAM

U163171E02
5.948,6.573 6.281,6.729 0.333,0.156 10 false ECM 5.677,2.479 6.219,2.646 0.542,0.167 10 false STSW 5.677,2.802 6.219,2.958 0.542,0.156 10 false ACCR 5.333,2.479 5.615,2.635 0.281,0.156 10 false A52 5.333,2.823 5.646,3.01 0.313,0.188 10 false A52 2.75,5.604 4.625,5.792 1.875,0.188 10 false Park/Neutral Position Switch 2.75,5.458 3.063,5.625 0.313,0.167 10 false C24 3.458,6.875 3.677,7.063 0.219,0.188 10 false ST 1.615,0.75 1.885,0.896 0.271,0.146 10 false 1C 1.979,0.865 2.698,1.031 0.719,0.167 10 false IG2 MAIN 2.938,0.281 3.271,0.448 0.333,0.167 10 false IG2 1.667,0.542 1.813,0.698 0.146,0.156 10 false 1 1.115,8.021 1.573,8.208 0.458,0.188 10 false Battery 4.75,7.542 5.229,7.698 0.479,0.156 10 false Starter 4.01,7.385 4.302,7.563 0.292,0.177 10 false D13 4.323,7.188 4.667,7.344 0.344,0.156 10 false D12 4.479,7 4.615,7.156 0.135,0.156 10 false 1 4.083,7.198 4.219,7.354 0.135,0.156 10 false 1 3.896,5.146 4.01,5.302 0.115,0.156 10 false 4 3.104,5.146 3.219,5.323 0.115,0.177 10 false 5 4.771,1.615 5.167,1.792 0.396,0.177 10 false IGN 4.552,1.396 4.667,1.573 0.115,0.177 10 false 1 4.552,1.771 4.667,1.948 0.115,0.177 10 false 2 4.427,3.677 4.604,3.823 0.177,0.146 10 false 5 4.75,4.49 4.896,4.667 0.146,0.177 10 false 1 4.427,4.49 4.594,4.688 0.167,0.198 10 false 3 4.75,3.677 4.917,3.833 0.167,0.156 10 false 2 1.615,1.083 1.906,1.25 0.292,0.167 10 false 1B 1.667,0.906 1.813,1.063 0.146,0.156 10 false 7 3.615,0.75 3.896,0.896 0.281,0.146 10 false 1B 3.667,0.552 3.813,0.708 0.146,0.156 10 false 8 3.615,1.083 3.885,1.229 0.271,0.146 10 false 1B 3.677,0.917 3.823,1.073 0.146,0.156 10 false 6 2.135,1.51 3.323,1.708 1.188,0.198 10 false Integration Relay 2.052,3.885 3.177,4.094 1.125,0.208 10 false Main Body ECU 2.552,2.104 2.958,2.271 0.406,0.167 10 false IG2D 2.49,2.458 2.958,2.615 0.469,0.156 10 false STSW 2.49,2.802 2.948,2.969 0.458,0.167 10 false ACCR 2.51,3.125 2.979,3.281 0.469,0.156 10 false STR2 2.594,3.469 3.031,3.625 0.438,0.156 10 false STR 3.021,2.146 3.292,2.313 0.271,0.167 10 false E2 3.01,2.49 3.302,2.646 0.292,0.156 10 false E4 3.021,2.823 3.313,2.99 0.292,0.167 10 false E2 3.021,3.156 3.313,3.313 0.292,0.156 10 false E4 3.021,3.5 3.281,3.656 0.26,0.156 10 false E1 3.042,1.948 3.313,2.115 0.271,0.167 10 false 11 3.083,2.313 3.375,2.469 0.292,0.156 10 false 4 3.083,2.656 3.375,2.823 0.292,0.167 10 false 3 3.083,2.99 3.375,3.146 0.292,0.156 10 false 6 3.083,3.323 3.344,3.479 0.26,0.156 10 false 8 5.677,3.156 6.219,3.313 0.542,0.156 10 false STAR 5.323,3.156 5.688,3.313 0.365,0.156 10 false C46 5.677,5.25 6.156,5.417 0.479,0.167 10 false NSW 5.698,5.813 6.188,5.969 0.49,0.156 10 false STA 5.323,5.26 5.656,5.417 0.333,0.156 10 false C46 5.333,5.833 5.615,5.99 0.281,0.156 10 false A52 4.979,2.479 5.281,2.656 0.302,0.177 10 false A38 4.99,2.823 5.271,2.979 0.281,0.156 10 false A38 4.958,2.656 5.323,2.823 0.365,0.167 10 false 22*1 4.948,2.292 5.302,2.469 0.354,0.177 10 false 47*1 4.979,3.156 5.344,3.313 0.365,0.156 10 false C45 4.948,2.99 5.302,3.156 0.354,0.167 10 false 52*1 4.969,5.26 5.302,5.417 0.333,0.156 10 false C45 4.969,5.823 5.271,5.979 0.302,0.156 10 false A38 4.948,5.073 5.292,5.24 0.344,0.167 10 false 49*1 4.938,5.656 5.281,5.813 0.344,0.156 10 false 48*1 5.323,2.656 5.677,2.823 0.354,0.167 10 false 22*2 5.302,2.292 5.656,2.458 0.354,0.167 10 false 47*2 5.323,2.99 5.656,3.135 0.333,0.146 10 false 52*2 5.302,5.073 5.646,5.24 0.344,0.167 10 false 49*2 5.323,5.656 5.667,5.813 0.344,0.156 10 false 48*2 1.646,4.5 1.865,4.688 0.219,0.188 10 false ST 1.375,4.323 1.531,4.51 0.156,0.188 10 false 1 1.385,4.719 1.542,4.906 0.156,0.188 10 false 2 3.115,6.448 3.292,6.594 0.177,0.146 10 false 5 3.906,6.135 4.052,6.313 0.146,0.177 10 false 1 3.906,6.448 4.052,6.625 0.146,0.177 10 false 3 3.115,6.135 3.281,6.292 0.167,0.156 10 false 2 4.938,4.042 5.542,4.229 0.604,0.188 10 false ST CUT 3.292,5.156 3.406,5.333 0.115,0.177 10 false L 3.698,5.146 3.813,5.323 0.115,0.177 10 false B 5.667,7.469 6.427,7.615 0.76,0.146 10 false *1: for LHD 5.667,7.792 6.427,7.938 0.76,0.146 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).



HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Data List / Starter Signal.


d.

Read the value displayed on the GTS when the engine switch is turned on (IG) and when the engine is started.

OK:
Condition Starter Signal
Engine switch turned on (IG) Close
Engine started Open




NG

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

7.CONFIRM WHETHER DTC OUTPUT RECURS
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITIONSWITCH - ECM)

NG

5.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITIONSWITCH - ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C45-49 (NSW) - A38-48 (STA) Always 10 kΩ or higher
C45-49 (NSW) or A38-48 (STA) - Body ground and other terminals Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C46-49 (NSW) - A52-48 (STA) Always 10 kΩ or higher
C46-49 (NSW) or A52-48 (STA) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the park/neutral position switch assembly connector.


e.

Reconnect the ECM connector.



OK

4.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

NEXT

7.CONFIRM WHETHER DTC OUTPUT RECURS
5.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Replace the park/neutral position switch assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL).



NEXT

7.CONFIRM WHETHER DTC OUTPUT RECURS
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

7.CONFIRM WHETHER DTC OUTPUT RECURS
7.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off.


d.

Turn the engine switch on (IG).


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.


f.

Confirm that the DTC is not output again.



NEXT

END