Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.

P0617
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.5 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
·

Starter relay (ST) circuit

·

Park/neutral position switch assembly

·

ECM



Related Data List
DTC No. Data List
P0617 Starter Signal

WIRING DIAGRAM

w/ Smart Entry and Start System

A375393E01
1.466,1.036 1.743,1.201 0.276,0.165 10 NE 6.111,1.036 6.533,1.201 0.422,0.165 10 NEO 5.768,1.043 6.099,1.208 0.332,0.165 10 A52 5.768,3.761 6.099,3.926 0.332,0.165 10 A52 5.424,1.568 5.756,1.733 0.332,0.165 10 C45 6.104,1.568 6.526,1.733 0.422,0.165 10 NSW 1.784,0.933 2.060,1.098 0.276,0.165 10 14 5.749,0.863 6.090,1.028 0.341,0.165 10 51*2 5.431,1.043 5.763,1.208 0.332,0.165 10 A38 5.413,0.863 5.754,1.028 0.341,0.165 10 51*1 5.41,1.4 5.751,1.565 0.341,0.165 10 49*1 5.775,1.561 6.106,1.726 0.332,0.165 10 C46 5.761,1.393 6.102,1.558 0.341,0.165 10 49*2 5.744,3.595 6.085,3.760 0.341,0.165 10 48*2 5.431,3.763 5.763,3.928 0.332,0.165 10 A38 5.408,3.597 5.749,3.762 0.341,0.165 10 48*1 1.784,1.446 2.060,1.612 0.276,0.165 10 10 1.784,1.979 2.060,2.144 0.276,0.165 10 12 1.275,1.554 1.718,1.719 0.443,0.165 10 STAR 0.528,2.628 0.971,2.793 0.443,0.165 10 E128 0.574,4.104 1.017,4.269 0.443,0.165 10 ST 3.269,4.608 3.712,4.773 0.443,0.165 10 ST 1.027,5.903 1.350,6.068 0.323,0.165 10 D13 0.71,6.795 1.412,6.960 0.702,0.165 10 Battery 1.593,6.664 2.295,6.829 0.702,0.165 10 Starter 1.742,5.674 2.065,5.839 0.323,0.165 10 D12 3.675,2.413 4.044,2.578 0.369,0.165 10 C24 0.528,2.824 1.660,2.989 1.133,0.165 10 Certification ECU 3.666,2.572 5.507,2.746 1.841,0.174 10 Park/Neutral Position Switch 1.387,2.086 1.737,2.251 0.350,0.165 10 STA 6.102,3.672 6.452,3.837 0.350,0.165 10 STA 4.544,1.988 4.820,2.153 0.276,0.165 10 4 3.545,1.988 3.765,2.153 0.221,0.165 10 5 2.55,4.136 2.771,4.302 0.221,0.165 10 5 2.55,5.01 2.771,5.175 0.221,0.165 10 3 2.998,5.01 3.219,5.175 0.221,0.165 10 1 2.998,4.136 3.219,4.302 0.221,0.165 10 2 3.727,1.988 3.947,2.153 0.221,0.165 10 L 4.334,1.988 4.555,2.153 0.221,0.165 10 B 3.932,5.922 5.924,6.120 1.992,0.198 10 *1: for LHD 3.932,6.223 5.924,6.421 1.992,0.198 10 *2: for RHD 6.347,4.905 6.886,5.259 0.539,0.354 10 ECM 1.891,5.493 2.112,5.658 0.221,0.165 10 1 1.107,5.731 1.328,5.896 0.221,0.165 10 1

w/o Smart Entry and Start System

A375780E02
0.438,1.479 0.833,1.677 0.396,0.198 10 false AM1 0.438,2.26 1.281,2.458 0.844,0.198 10 false J/B LH-AM 0.438,3.052 1.281,3.25 0.844,0.198 10 false ALT 2.885,4.208 3.146,4.406 0.26,0.198 10 false ST 0.729,0.365 1.125,0.563 0.396,0.198 10 false AM1 0.531,0.344 0.729,0.542 0.198,0.198 10 false 4 1.823,0.344 2.021,0.542 0.198,0.198 10 false 7 1.469,0.365 1.865,0.563 0.396,0.198 10 false ST2 5.417,0.49 5.813,0.688 0.396,0.198 10 false C45 5.406,0.302 5.802,0.5 0.396,0.198 10 false 49*1 5.792,0.49 6.188,0.688 0.396,0.198 10 false C46 2.958,1.813 3.156,2.01 0.198,0.198 10 false 4 4.031,1.781 4.229,1.979 0.198,0.198 10 false 5 5.771,0.302 6.167,0.5 0.396,0.198 10 false 49*2 5.427,3.656 5.823,3.854 0.396,0.198 10 false A38 6.167,3.646 6.563,3.844 0.396,0.198 10 false STA 5.417,3.448 5.813,3.646 0.396,0.198 10 false 48*1 5.802,3.656 6.198,3.854 0.396,0.198 10 false A52 5.771,3.448 6.167,3.646 0.396,0.198 10 false 48*2 6.167,0.479 6.625,0.677 0.458,0.198 10 false NSW 1.063,3.813 1.323,4.01 0.26,0.198 10 false ST 1.854,5.938 2.417,6.135 0.563,0.198 10 false Starter 0.531,5.875 1.094,6.073 0.563,0.198 10 false Battery 1.948,5.01 2.344,5.208 0.396,0.198 10 false D12 1.365,5.479 1.76,5.677 0.396,0.198 10 false D13 1.427,5.26 1.625,5.458 0.198,0.198 10 false 1 2.115,4.792 2.313,4.99 0.198,0.198 10 false 1 2.667,4.583 2.865,4.781 0.198,0.198 10 false 1 2.677,3.781 2.875,3.979 0.198,0.198 10 false 2 2.115,3.792 2.313,3.99 0.198,0.198 10 false 5 2.125,4.583 2.323,4.781 0.198,0.198 10 false 3 0.667,1.063 2.313,1.26 1.646,0.198 10 false Ignition Switch Assembly 2.219,2.354 4.688,2.583 2.469,0.229 10 false Park/Neutral Position Switch Assembly 2.229,2.188 2.552,2.385 0.323,0.198 10 false C24 0.656,0.896 1,1.094 0.344,0.198 10 false E93 3.25,4.854 5.24,5.052 1.99,0.198 10 false *1: for LHD 6.354,4.813 6.792,5.021 0.438,0.208 10 false ECM 3.25,5.156 5.24,5.354 1.99,0.198 10 false *2: for RHD 3.146,1.813 3.344,2.01 0.198,0.198 10 false B 3.844,1.792 4.042,1.99 0.198,0.198 10 false L

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).



HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Data List / Starter Signal.

Result:
Result Proceed to
Driving at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more OFF A
ON w/ Smart Entry and Start System B
w/o Smart Entry and Start System C




A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

3.REPAIR OR REPLACE HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

NG

3.REPAIR OR REPLACE HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (park/neutral position switch assembly - ST relay - ECM - main body ECU).



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.


Result:
Result Proceed to
DTC P0617 is output A
DTCs are not output B


A

5.CHECK SMART ENTRY AND START SYSTEM (START FANCTION)

B

END

5.CHECK SMART ENTRY AND START SYSTEM (START FANCTION)

OK

NG

REPAIR SMART ENTRY AND START SYSTEM

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

7.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

7.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>1VD-FTV (STARTING)>IGNITION SWITCH>INSPECTION).



OK

8.REPAIR OR REPLACE HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

NG

9.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
8.REPAIR OR REPLACE HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circuit).



NEXT

10.CONFIRM WHETHER DTC OUTPUT RECURS
9.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
a.

Replace the ignition switch assembly (See page Engine / Hybrid System>1VD-FTV (STARTING)>IGNITION SWITCH>REMOVAL).



NEXT

10.CONFIRM WHETHER DTC OUTPUT RECURS
10.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.



NEXT

END