Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0405  Exhaust Gas Recirculation Sensor "A" Circuit Low  P0406  Exhaust Gas Recirculation Sensor "A" Circuit High  P0407  Exhaust Gas Recirculation Sensor "B" Circuit Low  P0408  Exhaust Gas Recirculation Sensor "B" Circuit High  


DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback. The ECM then regulates the lift amount of the valve in accordance with engine running conditions.

P0405 (No. 1), P0407 (No. 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 5 seconds EGR valve position sensor output voltage is less than 0.1 V for 5 seconds.
(1 trip detection logic)
·

Open in EGR valve position sensor circuit

·

EGR valve assembly (EGR valve position sensor)

·

ECM



P0406 (No. 1), P0408 (No. 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 5 seconds EGR valve position sensor output voltage is more than 4.9 V for 5 seconds.
(1 trip detection logic)
·

Short in EGR valve position sensor circuit

·

EGR valve assembly (EGR valve position sensor)

·

ECM



MONITOR DESCRIPTION

When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit, and illuminates the MIL.

WIRING DIAGRAM

A182885E02
0.092,2.546 1.444,2.722 1.352,0.177 10 from EFI NO. 2 Fuse 3.435,0.754 3.674,0.914 0.239,0.160 10 VC 3.723,0.954 3.865,1.103 0.142,0.149 10 3 3.447,1.952 3.686,2.112 0.239,0.160 10 E2 3.723,2.152 3.865,2.301 0.142,0.149 10 2 3.336,2.431 3.673,2.591 0.337,0.160 10 EGR 2.023,2.431 2.262,2.591 0.239,0.160 10 +B 3.723,2.663 3.865,2.811 0.142,0.149 10 5 1.878,2.663 2.020,2.811 0.142,0.149 10 1 3.266,1.244 3.673,1.404 0.407,0.160 10 EGLS 5.669,0.754 6.158,0.914 0.489,0.160 10 VC 5.669,1.952 6.137,2.112 0.468,0.160 10 E2 5.669,2.447 6.110,2.607 0.442,0.160 10 EGRS 5.669,1.244 6.076,1.404 0.407,0.160 10 EGLS 3.723,1.443 3.865,1.592 0.142,0.149 10 4 5.375,0.954 5.566,1.103 0.191,0.149 10 91 5.382,2.152 5.566,2.301 0.184,0.149 10 92 5.382,2.631 5.573,2.780 0.191,0.149 10 82 5.669,4.912 6.137,5.072 0.468,0.160 10 EGS2 5.669,6.118 6.110,6.278 0.442,0.160 10 ERS2 5.382,5.112 5.566,5.261 0.184,0.149 10 89 5.368,6.306 5.546,6.455 0.178,0.149 10 42 5.905,6.84 6.822,6.989 0.917,0.149 10 C45*1, C46*2 5.905,6.991 6.265,7.140 0.360,0.149 10 ECM 5.382,1.443 5.566,1.592 0.184,0.149 10 88 2.376,3.033 2.678,3.203 0.302,0.170 10 C87 2.376,3.215 3.479,3.385 1.103,0.170 10 No. 1 EGR Valve 0.06,6.216 1.376,6.393 1.316,0.177 10 from EFI NO. 3 Fuse 3.435,4.425 3.674,4.585 0.239,0.160 10 VC 3.731,4.624 3.873,4.773 0.142,0.149 10 3 3.455,5.623 3.694,5.783 0.239,0.160 10 E2 3.731,5.822 3.873,5.971 0.142,0.149 10 2 3.336,6.13 3.673,6.290 0.337,0.160 10 EGR 2.031,6.13 2.270,6.290 0.239,0.160 10 +B 3.731,6.301 3.873,6.450 0.142,0.149 10 5 1.878,6.301 2.020,6.450 0.142,0.149 10 1 3.266,4.914 3.673,5.074 0.407,0.160 10 EGS2 3.731,5.114 3.873,5.263 0.142,0.149 10 4 2.376,6.704 2.678,6.874 0.302,0.170 10 C88 2.376,6.886 3.502,7.056 1.126,0.170 10 No. 2 EGR Valve 0.877,7.113 1.668,7.283 0.791,0.170 10 *1: for LHD 0.877,7.421 1.668,7.591 0.791,0.170 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
a.

Disconnect the No. 1 or No. 2 EGR valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
No. 1 (LHD)
Tester Connection Condition Specified Condition
C87-3 (VC) - C45-91 (VC) Always Below 1 Ω
C87-4 (EGLS) - C45-88 (EGLS) Always Below 1 Ω
C87-2 (E2) - C45-92 (E2) Always Below 1 Ω
C87-3 (VC) or C45-91 (VC) - Body ground Always 10 kΩ or higher
C87-4 (EGLS) or C45-88 (EGLS) - Body ground Always 10 kΩ or higher

No. 2 (LHD)
Tester Connection Condition Specified Condition
C88-3 (VC) - C45-91 (VC) Always Below 1 Ω
C88-4 (EGS2) - C45-89 (EGS2) Always Below 1 Ω
C88-2 (E2) - C45-92 (E2) Always Below 1 Ω
C88-3 (VC) or C45-91 (VC) - Body ground Always 10 kΩ or higher
C88-4 (EGS2) or C45-89 (EGS2) - Body ground Always 10 kΩ or higher

No. 1 (RHD)
Tester Connection Condition Specified Condition
C87-3 (VC) - C46-91 (VC) Always Below 1 Ω
C87-4 (EGLS) - C46-88 (EGLS) Always Below 1 Ω
C87-2 (E2) - C46-92 (E2) Always Below 1 Ω
C87-3 (VC) or C46-91 (VC) - Body ground Always 10 kΩ or higher
C87-4 (EGLS) or C46-88 (EGLS) - Body ground Always 10 kΩ or higher

No. 2 (RHD)
Tester Connection Condition Specified Condition
C88-3 (VC) - C46-91 (VC) Always Below 1 Ω
C88-4 (EGS2) - C46-89 (EGS2) Always Below 1 Ω
C88-2 (E2) - C46-92 (E2) Always Below 1 Ω
C88-3 (VC) or C46-91 (VC) - Body ground Always 10 kΩ or higher
C88-4 (EGS2) or C46-89 (EGS2) - Body ground Always 10 kΩ or higher




OK

2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
a.
U162939E01
0.142,0.001 0.345,0.200 0.203,0.199 10 *a 1.276,2.602 1.522,2.800 0.246,0.198 10 E2 1.882,2.602 2.128,2.800 0.246,0.198 10 VC 1.391,0.911 1.575,1.088 0.184,0.177 10 *A 2.487,0.911 2.671,1.088 0.184,0.177 10 *B 1.486,2.173 1.395,2.602 false 1.775,2.182 1.955,2.589 false 0.948,0.98 1.257,1.157 0.309,0.177 10 C87 2.031,0.98 2.340,1.157 0.309,0.177 10 C88

Disconnect the No. 1 or No. 2 EGR valve assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
No. 1
Tester Connection Switch Condition Specified Condition
C87-3 (VC) - C87-2 (E2) Ignition switch ON 4.5 to 5.5 V

No. 2
Tester Connection Switch Condition Specified Condition
C88-3 (VC) - C88-2 (E2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*A No. 1
*B No. 2
*a Front view of wire harness connector
(to EGR valve assembly)



OK

3.REPLACE EGR VALVE ASSEMBLY

NG

4.REPLACE ECM
3.REPLACE EGR VALVE ASSEMBLY

When DTC P0405 or P0406 is output:

·

Replace the No. 1 EGR valve assembly (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL).


When DTC P0407 or P0408 is output:

·

Replace the No. 2 EGR valve assembly (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL).



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE ECM

NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 5 seconds.


e.

Enter the following menus: Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END