Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)  P2238  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)  P2239  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)  P2240  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1)  P2241  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1)  P2242  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1)  P2252  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)  P2253  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)  P2255  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1)  P2256  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1)  


DESCRIPTION

HINT:
·

For more information on the air fuel ratio sensor and Diesel Particulate Filter (DPF), refer to the following procedures (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).

·

If P2237, P2238, P2239, P2240, P2441 or P2442 is present, refer to the DTC table for DPF system (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).

·

These DTCs are recorded when the air fuel ratio sensor has a malfunction, although the title says oxygen sensor.



The air fuel ratio sensor has the characteristic of providing output voltage which is proportional to the air-fuel ratio. The air fuel ratio sensor output voltage* is used by the ECM to control the air-fuel ratio.

The air fuel ratio sensor is located after the DPF catalytic converter. This sensor has been developed based on the structure and technology of a sensor that is used for gasoline engines. The cover portion of the sensor has been changed for use in the diesel engine with DPF in order to eliminate the influence of the sensor temperature and particulate matter (PM).

In order to reduce PM, the ECM adjusts the air-fuel ratio to a slightly rich value (but it is lean compared with the stoichiometric air-fuel ratio) based on signals from the air fuel ratio sensor. When the ECM performs PM forced regeneration using adding fuel by the exhaust fuel addition injector, the air-fuel ratio is also properly adjusted using the sensor.

*: The voltage value changes inside the ECM only.

A258975E07
5.24,1.979 5.771,2.49 true 5.021,1.792 5.688,1.979 true 5.156,1.385 5.667,1.333 true 5.385,1.271 5.708,1.094 true 5.177,1.729 5.688,1.979 true 3.208,2.25 3.854,1.906 false 3.042,2.219 2.313,1.854 true 2.583,2.604 2.813,2.802 0.229,0.198 10 false A 3.271,2.604 3.5,2.792 0.229,0.188 10 false A 1.76,1.75 2.313,1.99 0.552,0.24 10 false Element 0.677,2.073 1.552,2.292 0.875,0.219 10 false Exhaust Gas 4.875,2.635 5.719,2.875 0.844,0.24 10 false A-A Section 5.719,1.896 7.146,2.115 1.427,0.219 10 false Platinum Electrode 3.906,1.813 4.365,2.094 0.458,0.281 10 false Cover 5.802,2.427 6.094,2.625 0.292,0.198 10 false Air 5.771,0.927 6.313,1.156 0.542,0.229 10 false Heater 5.729,1.198 6.854,1.625 1.125,0.427 10 false Solid Electrolyte (Zirconia Element) 0.24,4.792 1.896,4.969 1.656,0.177 10 false AF Lambda B1S1 (B2S2) 0.229,6.104 1.969,6.313 1.74,0.208 10 false AFS Voltage B1S1 (B2S2) 2.042,4.906 2.208,5.115 0.167,0.208 10 false 1 2.031,4.396 2.198,4.604 0.167,0.208 10 false 2 2.042,6.292 2.208,6.5 0.167,0.208 10 false 1 2.042,6.813 2.208,7.021 0.167,0.208 10 false 0 2.031,5.438 2.198,5.646 0.167,0.208 10 false 0 2.042,5.771 2.208,5.979 0.167,0.208 10 false 2 2.302,5.688 2.531,5.938 0.229,0.25 10 false (V) 2.927,6.979 3.177,7.229 0.25,0.25 10 false 10 3.24,7.073 3.594,7.323 0.354,0.25 10 false 14.5 3.688,6.979 3.938,7.229 0.25,0.25 10 false 20 4.458,6.979 4.708,7.229 0.25,0.25 10 false 30 5.229,6.979 5.479,7.229 0.25,0.25 10 false 40 5.99,6.979 6.24,7.229 0.25,0.25 10 false 50 0.146,3.313 2.365,3.552 2.219,0.24 10 false Air-Fuel Ratio Displayed on Tester: 3.688,7.313 4.583,7.51 0.896,0.198 10 false Air-Fuel Ratio 3.708,4.969 6.76,5.177 3.052,0.208 10 false AF Lambda B1S1 (B2S2) = Air-Fuel Ratio / 14.5 2.604,8.281 3.021,8.469 0.417,0.188 10 false 0.060 4.833,8.281 5.25,8.469 0.417,0.188 10 false 0.508 5.406,8.281 5.823,8.469 0.417,0.188 10 false 0.787 5.958,8.281 6.375,8.469 0.417,0.188 10 false 0.978 6.51,8.281 6.927,8.469 0.417,0.188 10 false 1.373 4.281,8.281 4.698,8.469 0.417,0.188 10 false 0.336 3.729,8.281 4.146,8.469 0.417,0.188 10 false 0.268 3.167,8.281 3.583,8.469 0.417,0.188 10 false 0.170 2.188,8.281 2.375,8.469 0.188,0.188 10 false 0 2.104,8.729 2.438,8.917 0.333,0.188 10 false 14.5 6.031,8.729 6.365,8.917 0.333,0.188 10 false 30 2.688,8.74 3.021,8.927 0.333,0.188 10 false 15 4.906,8.74 5.24,8.927 0.333,0.188 10 false 20 6.615,8.729 6.948,8.917 0.333,0.188 10 false 50 3.802,8.74 4.135,8.927 0.333,0.188 10 false 17 3.229,8.74 3.563,8.927 0.333,0.188 10 false 16 0.375,8.729 1.323,8.979 0.948,0.25 10 false Air-Fuel Ratio 4.344,8.74 4.677,8.927 0.333,0.188 10 false 18 5.479,8.729 5.813,8.917 0.333,0.188 10 false 25 1.146,8.219 1.375,8.417 0.229,0.198 10 false (V) 0.313,8.146 1.188,8.51 0.875,0.365 10 false AFS Voltage B1S1 (B2S2) 0.333,7.615 1.208,8 0.875,0.385 10 false AF Lambda B1S1 (B2S2) 2.146,7.771 2.375,7.938 0.229,0.167 10 false 1.0 2.625,7.771 2.969,7.948 0.344,0.177 10 false 1.03 3.177,7.771 3.49,7.969 0.313,0.198 10 false 1.10 3.719,7.771 4.031,7.917 0.313,0.146 10 false 1.17 4.302,7.771 4.594,7.969 0.292,0.198 10 false 1.24 4.833,7.771 5.146,7.917 0.313,0.146 10 false 1.38 5.417,7.771 5.75,7.927 0.333,0.156 10 false 1.72 5.969,7.771 6.26,7.917 0.292,0.146 10 false 2.07 6.563,7.771 6.885,7.927 0.323,0.156 10 false 3.45 0.396,9.156 0.802,9.385 0.406,0.229 10 false HINT: 0.688,9.427 6.552,9.625 5.865,0.198 10 false *1: AFS Voltage B1S1 (B2S2) cannot be displayed correctly when the value is 0 V or less. 1.5,8.292 1.948,8.479 0.448,0.188 10 false -0.549 1.583,8.74 1.917,8.927 0.333,0.188 10 false 12 1.542,7.781 1.854,7.948 0.313,0.167 10 false 0.83 1.438,8.063 1.635,8.25 0.198,0.188 10 false *1 2.042,3.875 2.208,4.083 0.167,0.208 10 false 3

P2237 (Bank 1), P2240 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
·

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

·

Check that "Exhaust Temperature B1S1" displays 200°C (392°F) or higher using the GTS.


When either of the following conditions is met (1 trip detection logic):
·

Air fuel ratio sensor circuit malfunction

·

The resistance of the air fuel ratio sensor element is 250 Ω or higher for 5 seconds or more.


Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM



P2238 (Bank 1), P2241 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 7 seconds Air fuel ratio sensor (for bank 1, 2) circuit low
(1 trip detection logic)
Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM



P2239 (Bank 1), P2242 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 7 seconds Air fuel ratio sensor (for bank 1, 2) circuit high
(1 trip detection logic)
Main trouble area: Short in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM



P2252 (Bank 1), P2255 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 7 seconds Air fuel ratio sensor (for bank 1, 2) circuit low
(1 trip detection logic)
Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM



P2253 (Bank 1), P2256 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 7 seconds Air fuel ratio sensor (for bank 1, 2) circuit high
(1 trip detection logic)
Main trouble area: Short in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM



Related Data List
DTC No. Data List
P2237
P2238
P2239
P2252
P2253
·

AFS Voltage B1S1

·

Exhaust Temperature B1S1


P2240
P2241
P2242
P2255
P2256
·

AFS Voltage B2S1

·

Exhaust Temperature B2S1



MONITOR DESCRIPTION

The air fuel ratio sensor outputs a voltage in proportion to the air-fuel ratio. If impedance (alternating current resistance) or voltage output of the sensor deviates greatly from the standard range, the ECM interprets this as an open or short malfunction of the air fuel ratio sensor circuit.

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C159-3 (AF1+) - C45-102 (A1A+) Always Below 1 Ω
C159-4 (AF1-) - C45-103 (A1A-) Always Below 1 Ω
C158-3 (AF2+) - C45-125 (A2A+) Always Below 1 Ω
C158-4 (AF2-) - C45-126 (A2A-) Always Below 1 Ω
C159-3 (AF1+) or C45-102 (A1A+) - Body ground Always 10 kΩ or higher
C159-4 (AF1-) or C45-103 (A1A-) - Body ground Always 10 kΩ or higher
C158-3 (AF2+) or C45-125 (A2A+) - Body ground Always 10 kΩ or higher
C158-4 (AF2-) or C45-126 (A2A-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C159-3 (AF1+) - C46-102 (A1A+) Always Below 1 Ω
C159-4 (AF1-) - C46-103 (A1A-) Always Below 1 Ω
C158-3 (AF2+) - C46-125 (A2A+) Always Below 1 Ω
C158-4 (AF2-) - C46-126 (A2A-) Always Below 1 Ω
C159-3 (AF1+) or C46-102 (A1A+) - Body ground Always 10 kΩ or higher
C159-4 (AF1-) or C46-103 (A1A-) - Body ground Always 10 kΩ or higher
C158-3 (AF2+) or C46-125 (A2A+) - Body ground Always 10 kΩ or higher
C158-4 (AF2-) or C46-126 (A2A-) - Body ground Always 10 kΩ or higher



d.

Reconnect the air fuel ratio sensor connector.


e.

Reconnect the ECM connector.



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.REPLACE AIR FUEL RATIO SENSOR

When DTC P2237, P2238, P2239, P2252 or P2253 is output:

·

Replace the air fuel ratio sensor (for bank 1) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).


When DTC P2240, P2241, P2242, P2255 or P2256 is output:

·

Replace the air fuel ratio sensor (for bank 2) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).



NEXT

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Warm up the engine.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.



f.

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

HINT:

Make sure that the exhaust gas temperatures (Exhaust Temperature B1S1 and Exhaust Temperature B2S1) are 200°C (392°F) or higher.



g.

Confirm that the DTC is not output again.



OK

END

NG

4.REPLACE ECM
4.REPLACE ECM

NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Warm up the engine.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.



f.

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

HINT:

Make sure that the exhaust gas temperatures (Exhaust Temperature B1S1 and Exhaust Temperature B2S1) are 200°C (392°F) or higher.



g.

Confirm that the DTC is not output again.



NEXT

END