Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0107  Manifold Absolute Pressure / Barometric Pressure Circuit Low Input  P0108  Manifold Absolute Pressure / Barometric Pressure Circuit High Input  


DESCRIPTION

A208461E01
0.417,0.406 0.74,0.646 0.323,0.24 10 false V 0.156,0.813 0.594,1.042 0.438,0.229 10 false 3.586 0.167,1.917 0.615,2.135 0.448,0.219 10 false 0.386 1.021,2.323 1.198,2.469 0.177,0.146 10 false 40 2.333,2.323 2.604,2.469 0.271,0.146 10 false 320 0.979,2.656 1.25,2.802 0.271,0.146 10 false 300 0.938,2.802 1.323,3.042 0.385,0.24 10 false (11.8) 2.24,2.792 2.625,3.083 0.385,0.292 10 false (94.5) 2.854,2.771 3.302,3.083 0.448,0.313 10 false (in.Hg) 2.854,2.542 3.302,2.813 0.448,0.271 10 false mmHg 2.833,2.115 3.198,2.313 0.365,0.198 10 false kPa 2.854,2.26 3.24,2.5 0.385,0.24 10 false (abs) 2.24,2.646 2.573,2.792 0.333,0.146 10 false 2400 1.323,3.042 2.25,3.313 0.927,0.271 10 false Air Pressure

The manifold absolute pressure sensor detects the intake manifold pressure. The ECM determines the basic injection volume and injection advance timing based on the voltage output by the manifold absolute pressure sensor.

The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa [0 mmHg, 0 in.Hg]). As a result, the ECM controls the air-fuel ratio so that it reaches the proper level under any driving conditions.

P0107
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 0.1 V or less.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM



P0108
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 4.8 V or higher.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM



Related Data List
DTC No. Data List
P0107
P0108
·

MAP

·

Atmosphere Pressure



HINT:
·

If DTC P0107 and/or P0108 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power


·

When DTC P0107 or P0108 is stored, check the intake manifold pressure by entering the following menus: Engine and ECT / Data List / MAP.

Reference
Intake Manifold Pressure Malfunction
Approximately 0 kPa
·

Open in VC circuit

·

Short in PIM circuit


250 kPa (1875 mmHg, 73.8 in.Hg) or higher
·

Open in PIM circuit

·

Open in E circuit





WIRING DIAGRAM

A165731E79
5.781,2.208 6.146,2.406 0.365,0.198 10 false ECM 5.719,0.417 6.156,0.615 0.438,0.198 10 false VCPM 5.719,0.99 6.188,1.188 0.469,0.198 10 false PIM 5.719,1.531 6.188,1.729 0.469,0.198 10 false E2 1.469,0.469 1.75,0.646 0.281,0.177 10 false VC 0.323,2.188 2.938,2.5 2.615,0.313 10 false Manifold Absolute Pressure Sensor 1.406,1.031 1.771,1.24 0.365,0.208 10 false PIM 1.573,1.573 1.75,1.76 0.177,0.188 10 false E 1.854,1.156 2.01,1.313 0.156,0.156 10 false 2 1.833,0.583 1.969,0.75 0.135,0.167 10 false 3 1.844,1.688 1.948,1.875 0.104,0.188 10 false 1 0.323,2.031 0.635,2.188 0.313,0.156 10 false C80 5.781,2.042 6.708,2.229 0.927,0.188 10 false C45*1, C46*2 5.375,0.594 5.563,0.75 0.188,0.156 10 false 66 5.385,1.156 5.604,1.323 0.219,0.167 10 false 67 5.375,1.677 5.604,1.865 0.229,0.188 10 false 92 3.448,2.052 4.375,2.24 0.927,0.188 10 false *1: for LHD 3.448,2.354 4.375,2.542 0.927,0.188 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Data List / MAP.


d.

Read the value.

OK:

Same as the actual atmospheric pressure.


HINT:
·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather (high atmospheric pressure, low atmospheric pressure).

·

Also, check "Atmosphere Pressure" in the Data List.





OK

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C80-2 (PIM) - C45-67 (PIM) Always Below 1 Ω
C80-3 (VC) - C45-66 (VCPM) Always Below 1 Ω
C80-1 (E) - C45-92 (E2) Always Below 1 Ω
C80-2 (PIM) or C45-67 (PIM) - Body ground Always 10 kΩ or higher
C80-3 (VC) or C45-66 (VCPM) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C80-2 (PIM) - C46-67 (PIM) Always Below 1 Ω
C80-3 (VC) - C46-66 (VCPM) Always Below 1 Ω
C80-1 (E) - C46-92 (E2) Always Below 1 Ω
C80-2 (PIM) or C46-67 (PIM) - Body ground Always 10 kΩ or higher
C80-3 (VC) or C46-66 (VCPM) - Body ground Always 10 kΩ or higher




OK

3.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
a.
U163295E01
1.096,1.73 1.211,1.885 0.115,0.154 10 E 2.206,1.697 2.479,1.852 0.273,0.154 10 VC 0.241,0.222 0.425,0.391 0.184,0.170 10 *a 1.485,1.286 1.199,1.702 false 1.945,1.286 2.187,1.688 false 0.622,1.089 0.902,1.231 0.281,0.142 10 C80

Disconnect the manifold absolute pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C80-3 (VC) - C80-1 (E) Ignition switch ON 4.75 to 5.25 V


Text in Illustration
*a Front view of wire harness connector
(to Absolute Pressure Sensor)



OK

4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

6.REPLACE ECM
4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the GTS off.


e.

Start the engine.


f.

After the engine is started for 2 seconds, race the engine for 1 second.


g.

Turn the GTS on.


h.

Confirm that the DTC is not output again.


i.

Enter the following menus: Engine and ECT / Utility / All Readiness.


j.

Input DTC P0107 or P0108.


k.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL A
NORMAL B

HINT:

If STATUS is INCOMPLETE or N/A, race the engine for 1 minute, and then idle the engine for 5 minutes.




A

6.REPLACE ECM

B

END

6.REPLACE ECM

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the GTS off.


e.

Turn the ignition switch to ON for 3 seconds and turn the GTS on.


f.

After the engine is started for 2 seconds, race the engine for 1 second.


g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Engine and ECT / Utility / All Readiness.


ii.

Input DTC P0107 or P0108.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine for 1 minute, and then idle the engine for 5 minutes.




NEXT

END