Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0087  Fuel Rail / System Pressure - Too Low  P0190  Fuel Rail Pressure Sensor Circuit  P0192  Fuel Rail Pressure Sensor Circuit Low Input  P0193  Fuel Rail Pressure Sensor Circuit High Input  


DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail assembly (for bank 1) using the fuel pressure sensor, and controls the suction control valve to regulate the internal pressure so that it reaches the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip. This sensor outputs a voltage in proportion to the internal fuel pressure.

A168838E03
1.131,0.857 2.353,1.027 1.222,0.170 10 Output Voltage (V) 3.285,2.243 4.649,2.436 1.364,0.192 10 Fuel Pressure (MPa) 3.203,1.915 3.324,2.063 0.121,0.149 10 0 3.392,1.915 3.597,2.070 0.205,0.155 10 30 3.812,1.915 4.077,2.077 0.265,0.163 10 110 4.325,1.915 4.619,2.077 0.295,0.163 10 200 4.583,1.915 4.878,2.077 0.295,0.163 10 220 2.676,1.338 2.929,1.501 0.253,0.163 10 1.0 2.596,1.181 2.929,1.344 0.333,0.163 10 1.42 2.596,0.893 2.912,1.062 0.316,0.170 10 2.54 2.666,0.479 2.899,0.635 0.232,0.156 10 3.8 2.596,0.315 2.919,0.485 0.323,0.170 10 4.08 0.071,0 1.604,0.170 1.532,0.170 10 Property Output Voltage

P0087
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds Fuel pressure sensor output voltage stays at a fixed value a certain number of times (0.1 seconds or more).
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly (for bank 1))

·

Ran out of fuel

·

Fuel frozen

·

ECM



P0190
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second Fuel pressure sensor output voltage is 0.55 V or less, or 4.9 V or higher for 0.5 seconds.
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly (for bank 1))

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)



P0192
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second Fuel pressure sensor output voltage is 0.55 V or less for 0.5 seconds.
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly (for bank 1))

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)



P0193
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second Fuel pressure sensor output voltage is 4.9 V or higher for 0.5 seconds.
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly (for bank 1))

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)



Related Data List
DTC No. Data List
P0087
P0190
P0192
P0193
·

Common Rail Pressure

·

Target Common Rail Pressure



HINT:
·

Check Common Rail Pressure and compare it to Target Common Rail Pressure in the Data List by entering the following menus: Engine and ECT / Data List / Common Rail Pressure, Target Common Rail Pressure. Under stable conditions, the difference between Common Rail Pressure and Target Common Rail Pressure is 5000 kPa or less.

·

For more information on the fuel pressure sensor and common rail system, refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).

·

If DTC P0087 is stored, the following symptoms may appear:

-

Black smoke

-

Poor drivability

-

Lack of power

-

Lack of power due to accelerator restriction performed by fail-safe function


·

If DTC P0190, P0192 and/or P0193 is stored, the following symptom may appear:

-

Lack of power due to accelerator restriction performed by fail-safe function


·

If DTC P0190, P0192 and/or P0193 is stored, "Common Rail Pressure" always displays 0 kPa or 200000 kPa.



MONITOR DESCRIPTION

P0087 (Fuel pressure sensor output stays at fixed value):
·

Under normal conditions, the internal fuel pressure of the common rail assembly usually fluctuates by 1000 to 2000 kPa (10 to 20 kgf/cm2, 145 to 290 psi) even when driving conditions are constant. This DTC is stored if there is no fluctuation of the fuel pressure. The internal fuel pressure is approximately 27000 to 49000 kPa (275 to 500 kgf/cm2, 3915 to 7105 psi) when idling, and it increases to approximately 57000 to 77000 kPa (581 to 785 kgf/cm2, 8265 to 11165 psi) when running the engine at 3000 rpm.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

·

The diagram below indicates that fuel pressure rises as engine speed increases, but for the malfunction indicated by this DTC, that does not happen.

U163040E02
4.698,1.771 4.188,1.438 false 4.698,1.771 4.833,1.771 false 5.406,0.573 5.604,0.573 false 0.083,0.063 1.927,0.271 1.844,0.208 10 false P0087 Malfunction Detection 2.271,0.552 3.781,0.781 1.51,0.229 10 false Common Rail Pressure 4.844,1.677 5.51,1.875 0.667,0.198 10 false Abnormal 5.698,0.458 6.281,0.656 0.583,0.198 10 false Normal 2.292,2.167 3.24,2.375 0.948,0.208 10 false Engine Speed 5.229,3.375 5.615,3.542 0.385,0.167 10 false Time



P0190, P0192 and P0193 (Open or short in fuel pressure sensor circuit):

These DTCs are stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short malfunction of the sensor circuit.

If these DTCs are stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


WIRING DIAGRAM

A130470E09
0.563,3.292 1.958,3.49 1.396,0.198 10 false Fuel Pressure Sensor 0.563,3.125 0.875,3.323 0.313,0.198 10 false C82 1.833,1.094 2.094,1.292 0.26,0.198 10 false VC 1.833,1.833 2.083,2.01 0.25,0.177 9 false PR 1.844,2.563 2.073,2.76 0.229,0.198 10 false E2 2.167,2.833 2.333,3.063 0.167,0.229 10 false 1 5.104,2.833 5.323,3.063 0.219,0.229 10 false 95 2.167,2.083 2.333,2.313 0.167,0.229 10 false 2 5.094,2.083 5.333,2.313 0.24,0.229 10 false 72 2.167,1.333 2.333,1.563 0.167,0.229 10 false 3 5.052,1.344 5.344,1.552 0.292,0.208 10 false 118 5.427,1.115 5.844,1.313 0.417,0.198 10 false VCM 5.427,1.865 5.833,2.063 0.406,0.198 10 false PCR1 5.406,2.594 5.771,2.792 0.365,0.198 10 false E2M 5.729,3.292 6.094,3.49 0.365,0.198 10 false ECM 5.719,3.125 6.646,3.302 0.927,0.177 10 false C45*1, C46*2 3.073,3.052 3.896,3.25 0.823,0.198 10 false *1: for LHD 3.083,3.354 3.906,3.552 0.823,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:
·

If DTCs relating to different systems which share terminal E2 as their ground are stored, check this ground circuit first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
P0190, P0192 or P0193 is output A
P0087 is output B



A

2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

B

4.REPLACE COMMON RAIL ASSEMBLY (FOR BANK 1) (FUEL PRESSURE SENSOR)
2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C82-2 (PR) - C45-72 (PCR1) Always Below 1 Ω
C82-3 (VC) - C45-118 (VCM) Always Below 1 Ω
C82-1 (E2) - C45-95 (E2M) Always Below 1 Ω
C82-2 (PR) or C45-72 (PCR1) - Body ground Always 10 kΩ or higher
C82-3 (VC) or C45-118 (VCM) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C82-2 (PR) - C46-72 (PCR1) Always Below 1 Ω
C82-3 (VC) - C46-118 (VCM) Always Below 1 Ω
C82-1 (E2) - C46-95 (E2M) Always Below 1 Ω
C82-2 (PR) or C46-72 (PCR1) - Body ground Always 10 kΩ or higher
C82-3 (VC) or C46-118 (VCM) - Body ground Always 10 kΩ or higher




OK

3.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
U163035E01
1.573,1.113 1.858,1.283 0.285,0.170 10 C82 1.029,2.718 1.259,2.888 0.230,0.170 10 E2 2.199,2.718 2.485,2.888 0.285,0.170 10 VC 1.937,2.17 2.207,2.715 false 1.529,2.164 1.204,2.718 false 0.291,0.536 0.577,0.706 0.285,0.170 10 *a

a.

Disconnect the fuel pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C82-3 (VC) - C82-1 (E2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Fuel Pressure Sensor)



OK

4.REPLACE COMMON RAIL ASSEMBLY (FOR BANK 1) (FUEL PRESSURE SENSOR)

NG

7.REPLACE ECM
4.REPLACE COMMON RAIL ASSEMBLY (FOR BANK 1) (FUEL PRESSURE SENSOR)
a.

Replace the common rail assembly (for bank 1) (See page Engine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL>REMOVAL).



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM

b.

Perform PM forced regeneration (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.




NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P0190, P0192, P0193)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P0190, P0192, P0193)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.



d.

Let the engine idle for 60 seconds, and then quickly increase the engine speed to 2500 rpm repeatedly for 30 seconds.


e.

Enter the following menus: Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Result
Result Proceed to
P0087, P0190, P0192 or P0193 is output A
No DTC is output B



A

7.REPLACE ECM

B

END

7.REPLACE ECM

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Let the engine idle for 60 seconds, and then quickly increase the engine speed to 2500 rpm repeatedly for 30 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Engine and ECT / Utility / All Readiness.


ii.

Input DTC P0087, P0190, P0192 or P0193.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.




NEXT

END