The ECM opens and closes the throttle valve using a rotary solenoid type actuator. Due to the opening and closing of the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state. | Target and actual opening angle of the throttle valve differs for approximately 20 seconds.
(1 trip detection logic) |
·
Throttle valve stuck ·
Throttle valve does not move smoothly ·
Open or short in throttle control motor circuit ·
ECM |
| The throttle motor activation duty exceeds the threshold for 0.5 seconds a certain number of times (40 seconds or more).
(1 trip detection logic) |
| DTC No. | Data List |
|---|---|
| P0488 | ·
Throttle Motor Duty ·
Actual Throttle Position |
| P213B | ·
Throttle Motor Duty #2 ·
Actual Throttle Position #2 |
| Condition | Throttle Valve Position |
|---|---|
| Moment when accelerator pedal is depressed further or released at 3000 rpm | Throttle valve opening angle varies smoothly |
The ECM opens and closes the throttle valve by adjusting the current flowing to the rotary solenoid with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and illuminate the MIL.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
Although the DTC titles say "exhaust gas recirculation throttle position control range / performance", these DTCs relate to the throttle valve
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Engine and ECT / Active Test / Diesel Throttle Target Angle or Diesel Throttle Target Angle #2.
While continuously changing the Active Test value to 0, 30, 60, 90, 60, 30 and 0%, check that "Actual Throttle Position" or "Actual Throttle Position #2" smoothly changes to the set opening amount.
Value smoothly changes to set opening amount.
OK
NG
Disconnect the throttle control motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C85-2 (VCR) - Body ground | Engine switch on (IG) | 11 to 14 V |
| C86-2 (VCR) - Body ground | Engine switch on (IG) | 11 to 14 V |
| *A | for Bank 1 |
| *B | for Bank 2 |
| *a | Front view of wire harness connector
(to Throttle Control Motor) |
Reconnect the throttle control motor connector.
OK
NG
Disconnect the throttle control motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C85-3 (E2R) - Body ground | Always | Below 1 Ω |
| C86-3 (E2R) - Body ground | Always | Below 1 Ω |
Reconnect the throttle control motor connector.
OK
NG
Disconnect the throttle control motor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C85-1 (VTAR) - C45-57 (LUSL) | Always | Below 1 Ω |
| C86-1 (VTAR) - C45-56 (LUS2) | Always | Below 1 Ω |
| C85-1 (VTAR) or C45-57 (LUSL) - Body ground | Always | 10 kΩ or higher |
| C86-1 (VTAR) or C45-56 (LUS2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C85-1 (VTAR) - C46-57 (LUSL) | Always | Below 1 Ω |
| C86-1 (VTAR) - C46-56 (LUS2) | Always | Below 1 Ω |
| C85-1 (VTAR) or C46-57 (LUSL) - Body ground | Always | 10 kΩ or higher |
| C86-1 (VTAR) or C46-56 (LUS2) - Body ground | Always | 10 kΩ or higher |
Reconnect the throttle control motor connector.
Reconnect the ECM connector.
OK
NG
Visually check for deposits in the diesel throttle body assembly. If there are deposits, clean the diesel throttle body assembly.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Engine and ECT / Active Test / Diesel Throttle Target Angle or Diesel Throttle Target Angle #2.
While continuously changing the Active Test value to 0, 30, 60, 90, 60, 30 and 0%, check that "Actual Throttle Position" or "Actual Throttle Position #2" smoothly changes to the set opening amount.
Value smoothly changes to set opening amount.
OK
NG
When DTC P0488 is output:
Replace the diesel throttle body assembly (for bank 1) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL).
When DTC P213B is output:
Replace the diesel throttle body assembly (for bank 2) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL).
NEXT
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR).
Turn the engine switch off and wait for 30 seconds.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine.
Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm and lower it.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0488 or P213B is output | A |
| No DTC is output | B |
A
B
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR).
Turn the engine switch off and wait for 30 seconds.
Start the engine.
Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm, and then lower it.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Engine and ECT / Utility / All Readiness.
Input DTC P0488 and P213B.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm again, and then idle the engine for 5 minutes.
NEXT