Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF)
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) U

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  FAIL-SAFE CHART  


FAIL-SAFE CHART


If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily.

DTC No. Detection Item Fail-safe Operation Fail-safe Deactivation Condition
P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P0046 Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance The engine power is limited. Ignition switch off
P0047 Turbocharger/ Supercharger Boost Control "A" Circuit Low The engine power is limited. Ignition switch off
P0048 Turbocharger/ Supercharger Boost Control "A" Circuit High The engine power is limited. Ignition switch off
P004B Turbocharger / Supercharger Boost Control Solenoid "B" Circuit Range / Performance The engine power is limited. Ignition switch off
P004C Turbocharger/ Supercharger Boost Control "B" Circuit Low The engine power is limited. Ignition switch off
P004D Turbocharger/ Supercharger Boost Control "B" Circuit High The engine power is limited. Ignition switch off
P0051 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P0052 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P007C Charge Air Cooler Temperature Sensor Circuit Low The intake air temperature is fixed at a specified value. Pass condition detected
P007D Charge Air Cooler Temperature Sensor Circuit High The intake air temperature is fixed at a specified value. Pass condition detected
P0087 Fuel Rail/System Pressure - Too Low The engine power is reduced by 90%.* Ignition switch off
P0088 Fuel Rail/System Pressure - Too High The engine power is reduced by 90%.* Ignition switch off
P0093 Fuel System Leak Detected - Large Leak The engine power is reduced by 90%.* Ignition switch off
P0100 Mass Air Flow Circuit Malfunction The engine power is limited. Pass condition detected
P0101 Mass or Volume Air Flow Circuit The engine power is limited. Ignition switch off
P0107 Manifold Absolute Pressure/Barometric Pressure Circuit Low Input The turbo pressure is fixed at a specified value. Pass condition detected
P0108 Manifold Absolute Pressure/Barometric Pressure Circuit High Input The turbo pressure is fixed at a specified value. Pass condition detected
P0112 Intake Air Temperature Circuit Low Input The intake air temperature value is fixed. Pass condition detected
P0113 Intake Air Temperature Circuit High Input The intake air temperature value is fixed. Pass condition detected
P0115 Engine Coolant Temperature Circuit The engine coolant temperature sensor output is fixed at a specified value (the fixed value varies depending on conditions). Pass condition detected
P0117 Engine Coolant Temperature Circuit Low Input The engine coolant temperature sensor output is fixed at a specified value (the fixed value varies depending on conditions). Pass condition detected
P0118 Engine Coolant Temperature Circuit High Input The engine coolant temperature sensor output is fixed at a specified value (the fixed value varies depending on conditions). Pass condition detected
P0122 Throttle/Pedal Position Sensor/Switch "A" Circuit Low Input The engine power is limited. Ignition switch off
P0123 Throttle/Pedal Position Sensor/Switch "A" Circuit High Input The engine power is limited. Ignition switch off
P0180 Fuel Temperature Sensor "A" Circuit The fuel temperature is fixed at a specified value. Pass condition detected
P0182 Fuel Temperature Sensor "A" Circuit Low Input The fuel temperature is fixed at a specified value. Pass condition detected
P0183 Fuel Temperature Sensor "A" Circuit High Input The fuel temperature is fixed at a specified value. Pass condition detected
P0190 Fuel Rail Pressure Sensor Circuit
·

The main and sub circuits of the fuel pressure sensor are malfunctioning:

-

The engine power is reduced by 90%.*


·

The main or sub circuit of the fuel pressure sensor is malfunctioning:

-

The engine power is limited.



Ignition switch off
P0192 Fuel Rail Pressure Sensor Circuit Low Input
·

The main and sub circuits of the fuel pressure sensor are malfunctioning:

-

The engine power is reduced by 90%.*


·

The main or sub circuit of the fuel pressure sensor is malfunctioning:

-

The engine power is limited.



Ignition switch off
P0193 Fuel Rail Pressure Sensor Circuit High Input
·

The main and sub circuits of the fuel pressure sensor are malfunctioning:

-

The engine power is reduced by 90%.*


·

The main or sub circuit of the fuel pressure sensor is malfunctioning:

-

The engine power is limited.



Ignition switch off
P0201
P0202
P0203
P0204
P0205
P0206
P0207
P0208
Injector Circuit / Open - (Cylinder 1 to 8) The engine power is limited. Ignition switch off to on (IG) or STA on
P0222 Throttle/Pedal Position Sensor/Switch "B" Circuit Low Input The engine power is limited. Ignition switch off
P0223 Throttle/Pedal Position Sensor/Switch "B" Circuit High Input The engine power is limited. Ignition switch off
P0299 Turbocharger / Supercharger Underboost The engine power is limited. Pass condition detected
P0335 Crankshaft Position Sensor "A" Circuit The engine power is reduced by 90%.* Pass condition detected
P0339 Crankshaft Position Sensor "A" Circuit Intermittent The engine power is reduced by 90%.* Pass condition detected
P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) The engine power is reduced by 90%.* Pass condition detected
P0400 Exhaust Gas Recirculation Flow The engine power is limited. Ignition switch off
P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low The engine power is limited. Ignition switch off
P0406 Exhaust Gas Recirculation Sensor "A" Circuit High The engine power is limited. Ignition switch off
P0407 Exhaust Gas Recirculation Sensor "B" Circuit Low The engine power is limited. Ignition switch off
P0408 Exhaust Gas Recirculation Sensor "B" Circuit High The engine power is limited. Ignition switch off
P042E Exhaust Gas Recirculation "A" Control Stuck Open The engine power is limited. Ignition switch off
P045E Exhaust Gas Recirculation "B" Control The engine power is limited. Ignition switch off
P0500 Vehicle Speed Sensor "A" The vehicle speed is fixed at 0 km/h (0 mph). Pass condition detected
P0545 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 1) PM forced regeneration is prohibited. Pass condition detected
P0546 Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 1) PM forced regeneration is prohibited. Pass condition detected
P0548 Exhaust Gas Temperature Sensor Circuit Low (Bank 2 Sensor 1) PM forced regeneration is prohibited. Pass condition detected
P0549 Exhaust Gas Temperature Sensor Circuit High (Bank 2 Sensor 1) PM forced regeneration is prohibited. Pass condition detected
P0606 ECM / PCM Processor The engine power is reduced by 90%.* Pass condition detected
P060A Internal Control Module Monitoring Processor Performance The engine power is reduced by 90%.* Pass condition detected
P060B Internal Control Module A/D Processing Performance The engine power is reduced by 90%.* Pass condition detected
P0627 Fuel Pump Control Circuit / Open The engine power is limited. Pass condition detected
P062D No. 1 Fuel Injector Driver Circuit Performance
·

The engine power is limited.

·

Powering of the EDU relay is prohibited.


Ignition switch off
P062E No. 2 Fuel Injector Driver Circuit Performance
·

The engine power is limited.

·

Powering of the EDU relay is prohibited.


Ignition switch off
P1229 Fuel Pump System The engine power is limited. Ignition switch off
P1251 Turbocharger / Supercharger Overboost Condition (Too High) The engine power is limited. Ignition switch off
P1271 Fuel Regulator Circuit Malfunction (EDU Drive) The engine power is limited. Ignition switch off
P1272 Fuel Pressure Regulator Malfunction The engine power is limited. Ignition switch off
P1626 Idle Signal Output Value Low The engine power is limited. Ignition switch off
P1627 Idle Signal Output Value High The engine power is limited. Ignition switch off
P1629 Idle Signal Output Value Low Bank 2 The engine power is limited. Ignition switch off
P162A Idle Signal Output Value High Bank 2 The engine power is limited. Ignition switch off
P200C Diesel Particulate Filter Over Temperature Bank 1 PM forced regeneration is prohibited. Ignition switch off
P200D Diesel Particulate Filter Temperature Too High PM forced regeneration is prohibited. Ignition switch off
P200E Catalyst System Temperature Too High Bank 1 PM forced regeneration is prohibited. Ignition switch off
P200F Catalyst System Temperature Too High Bank 2 PM forced regeneration is prohibited. Ignition switch off
P2032 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2) PM forced regeneration is prohibited. Pass condition detected
P2033 Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 2) PM forced regeneration is prohibited. Pass condition detected
P2035 Exhaust Gas Temperature Sensor Circuit Low (Bank 2 Sensor 2) PM forced regeneration is prohibited. Pass condition detected
P2036 Exhaust Gas Temperature Sensor Circuit High (Bank 2 Sensor 2) PM forced regeneration is prohibited. Pass condition detected
P2084 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2 PM forced regeneration is prohibited. Pass condition detected
P2086 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 2 Sensor 2 PM forced regeneration is prohibited. Pass condition detected
P20CD Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit
·

The engine power is reduced by 90%.*

·

PM forced regeneration is prohibited.


Pass condition detected
P20CF Exhaust Aftertreatment Fuel Injector "A" Stuck Open The engine power is reduced by 90%.* Pass condition detected
P20D3 Open in Exhaust Aftertreatment Fuel Injector "B" Control Circuit
·

The engine power is reduced by 90%.*

·

PM forced regeneration is prohibited.


Pass condition detected
P20D5 Exhaust Aftertreatment Fuel Injector "B" Stuck Open The engine power is reduced by 90%.* Pass condition detected
P2120 Throttle/Pedal Position Sensor/Switch "D" Circuit The engine power is limited. Ignition switch off
P2121 Throttle/Pedal Position Sensor/Switch "D" Circuit Range/Performance The engine power is limited. Ignition switch off
P2122 Throttle/Pedal Position Sensor/Switch "D" Circuit Low Input The engine power is limited. Ignition switch off
P2123 Throttle/Pedal Position Sensor/Switch "D" Circuit High Input The engine power is limited. Ignition switch off
P2125 Throttle/Pedal Position Sensor/Switch "E" Circuit The engine power is limited. Ignition switch off
P2127 Throttle/Pedal Position Sensor/Switch "E" Circuit Low Input The engine power is limited. Ignition switch off
P2128 Throttle/Pedal Position Sensor/Switch "E" Circuit High Input The engine power is limited. Ignition switch off
P2138 Throttle/Pedal Position Sensor/Switch "D"/"E" Voltage Correlation The engine power is limited. Ignition switch off
P213B Exhaust Gas Recirculation Throttle Position Control (Range/Performance) The engine power is limited. Ignition switch off
P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2197 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2226 Barometric Pressure Circuit The atmospheric pressure is fixed at a specified value. Pass condition detected
P2228 Barometric Pressure Circuit Low Input The atmospheric pressure is fixed at a specified value. Pass condition detected
P2229 Barometric Pressure Circuit High Input The atmospheric pressure is fixed at a specified value. Pass condition detected
P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2240 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2241 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2242 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2255 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2256 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1) The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. Pass condition detected
P2428 Exhaust Gas Temperature Too High Bank 1 PM forced regeneration is prohibited. Ignition switch off
P2429 Exhaust Gas Temperature Too High Bank 2 PM forced regeneration is prohibited. Ignition switch off
P242B Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 3 PM forced regeneration is prohibited. Pass condition detected
P242C Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 3 PM forced regeneration is prohibited. Pass condition detected
P242D Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 3 PM forced regeneration is prohibited. Pass condition detected
P244B Diesel Particulate Filter Differential Pressure Too High
·

The engine power is limited.

·

PM forced regeneration is prohibited.


Ignition switch off
P244C Exhaust Temperature Too Low for Particulate Filter Regeneration Bank 1 PM forced regeneration is prohibited. Ignition switch off
P244E Exhaust Temperature Too Low for Particulate Filter Regeneration Bank 2 PM forced regeneration is prohibited. Ignition switch off
P2458 Diesel Particulate Filter Regeneration Duration PM forced regeneration is prohibited. Ignition switch off
P2463 Diesel Particulate Filter Restriction - Soot Accumulation
·

The engine power is limited.

·

PM forced regeneration is prohibited.


Pass condition detected
P2465 Diesel Particulate Filter Differential Pressure Too High Bank 2
·

The engine power is limited.

·

PM forced regeneration is prohibited.


Ignition switch off
P2467 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 2 Sensor 3 PM forced regeneration is prohibited. Pass condition detected
P2468 Exhaust Gas Temperature Sensor Circuit Low Bank 2 Sensor 3 PM forced regeneration is prohibited. Pass condition detected
P2469 Exhaust Gas Temperature Sensor Circuit High Bank 2 Sensor 3 PM forced regeneration is prohibited. Pass condition detected
P2564 Turbocharger/ Supercharger Boost Control Position Sensor "A" Circuit Low The engine power is limited. Ignition switch off
P2565 Turbocharger/ Supercharger Boost Control Position Sensor "A" Circuit High The engine power is limited. Ignition switch off
P2588 Turbocharger/ Supercharger Boost Control Position Sensor "B" Circuit Low The engine power is limited. Ignition switch off
P2589 Turbocharger/ Supercharger Boost Control Position Sensor "B" Circuit High The engine power is limited. Ignition switch off

HINT:

*: Engine power is limited immediately after the DTC is stored.