These DTCs indicate that the DC motor of the turbocharger is malfunctioning. The ECM monitors the DC motor current to detect an open or short in the DC motor circuit. If the current meets certain criteria, the ECM stores a DTC and illuminates the MIL immediately.
The DC motor is used to operate the nozzle vane of the turbocharger. The nozzle vane opens and closes to change the velocity of exhaust emissions in order to control the turbo pressure. The ECM varies the duty ratio of the DC motor in accordance with the driving conditions.
If the nozzle vane is stuck closed (DC motor stuck off), drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (DC motor stuck on), drivability may deteriorate at intermediate throttle positions or the engine power may be insufficient.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Ignition switch ON for 5 seconds | Either of the following conditions are met when the motor is driving (1 trip detection logic):
·
DC motor duty ratio is +/-100% for 5 seconds or more. ·
DC motor current is 2.2 A or more for 5 seconds or more. |
·
Open or short in DC motor (turbocharger sub-assembly) circuit ·
DC motor (turbocharger sub-assembly) ·
Turbocharger nozzle vane is stuck or movement is irregular |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| 2 seconds after engine is started, race engine for 1 second | The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more (1 trip detection logic). | ·
Open in DC motor (turbocharger sub-assembly) circuit ·
DC motor (turbocharger sub-assembly) ·
Turbocharger nozzle vane is stuck or movement is irregular |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| 2 seconds after engine is started, race engine for 1 second | Overcurrent is detected 25 times or more (0.4 seconds or more) (1 trip detection logic). | ·
Short in DC motor (turbocharger sub-assembly) circuit ·
DC motor (turbocharger sub-assembly) ·
Turbocharger nozzle vane is stuck or movement is irregular |
If DTC P0046, P0047, P0048, P004B, P004C or P004D is stored, the following symptom may appear.
Stuck closed malfunction:
- Vehicle surge when driving with full load
Stuck open malfunction:
- Lack of power
- Vehicle surge or hesitation under light or medium load
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0046, P0047, P0048, P004B, P004C or P004D is output | A |
| P0046, P0047, P0048, P004B, P004C or P004D and other DTCs are output | B |
If codes other than P0046, P0047, P0048, P004B, P004C or P004D are output, perform troubleshooting for those DTCs first.
A
B
(See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Engine and ECT / Active Test / Test the Turbo Charger Step Motor (Test the Turbo Charger Step Motor #2) / Data List / Target VN Turbo Position (Target VN Turbo Position #2) and Actual VN Turbo Position (Actual VN Turbo Position #2).
While changing the Active Test value to 20, 95, 60 and 20%, check that Actual VN Turbo Position (Actual VN Turbo Position #2) smoothly changes to the set opening amount.
When moving the vanes toward the fully closed position, make sure that Actual VN Turbo Position (Actual VN Turbo Position #2) does not become 5% or less.
The Actual VN Turbo Position (Actual VN Turbo Position #2) value follows the Target VN Turbo Position (Target VN Turbo Position #2).
OK
(See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>CHECK FOR INTERMITTENT PROBLEMS)
NG
Disconnect the DC motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (M-) - 2 (M+) | Always | 1 to 100 Ω |
| 1 (M2-) - 2 (M2+) | Always | 1 to 100 Ω |
| *a | Component without harness connected
(DC Motor) |
OK
NG
Disconnect the DC motor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C90-2 (M+) - C45-86 (M+) | Always | Below 1 Ω |
| C90-1 (M-) - C45-85 (M-) | Always | Below 1 Ω |
| z67-2 (M2+) - C45-18 (VN2+) | Always | Below 1 Ω |
| z67-1 (M2-) - C45-41 (VN2-) | Always | Below 1 Ω |
| C90-2 (M+) or C45-86 (M+) - Body ground | Always | 10 kΩ or higher |
| C90-1 (M-) or C45-85 (M-) - Body ground | Always | 10 kΩ or higher |
| z67-2 (M2+) or C45-18 (VN2+) - Body ground | Always | 10 kΩ or higher |
| z67-1 (M2-) or C45-41 (VN2-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C90-2 (M+) - C46-86 (M+) | Always | Below 1 Ω |
| C90-1 (M-) - C46-85 (M-) | Always | Below 1 Ω |
| z67-2 (M2+) - C46-18 (VN2+) | Always | Below 1 Ω |
| z67-1 (M2-) - C46-41 (VN2-) | Always | Below 1 Ω |
| C90-2 (M+) or C46-86 (M+) - Body ground | Always | 10 kΩ or higher |
| C90-1 (M-) or C46-85 (M-) - Body ground | Always | 10 kΩ or higher |
| z67-2 (M2+) or C46-18 (VN2+) - Body ground | Always | 10 kΩ or higher |
| z67-1 (M2-) or C46-41 (VN2-) - Body ground | Always | 10 kΩ or higher |
Reconnect the DC motor connector.
Reconnect the ECM connector.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
When DTC P0046, P0047 or P0048 is output:
Replace the turbocharger sub-assembly (for bank 1) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).
When DTC P004B, P004C or P004D is output:
Replace the turbocharger sub-assembly (for bank 2) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON for 5 seconds or more.
2 seconds after the engine is started, race the engine for 1 second.
Enter the following menus: Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT