Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P062F  Internal Control Module EEPROM Error  


DESCRIPTION

P062F
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 1 second When any condition below is met (1 trip detection logic):
·

Injector compensation code is not registered.

·

Wrong injector compensation code is registered.

·

Pilot quantity learning value is not registered.

·

Catalyst deterioration learning value is not registered.

·

Crank Time Compensation Learning value is not registered.*

·

A/F Sensor Compensation Learning value is not registered.*


·

Injector compensation code

·

Pilot quantity learning value

·

Catalyst thermal deterioration value

·

A/F sensor compensation learning value

·

Crank time compensation learning value

·

ECM



*: When this malfunction occurs, the MIL does not illuminate.

NOTICE:
·

When an injector assembly is replaced, the new injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.

·

Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

·

When an injector assembly is replaced, perform pilot quantity learning. When the ECM is replaced, all of the existing pilot quantity learning values must be input into the new ECM.

·

When the exhaust pipe assembly (DPF catalytic converter) is replaced, the new catalyst thermal deterioration value must be input into the ECM. When the ECM is replaced, the existing catalyst thermal deterioration value must be input into the new ECM.



HINT:

When replacing the ECM with a new one, if the injector compensation code, pilot quantity learning value and/or catalyst thermal deterioration value are not entered, DTC P062F will be stored.


When replacing the ECM with a new one, input all learning values and codes into the new ECM as follows:


a.

Prior to replacing the ECM, use the GTS to read and save each learning value and code from the original ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).


b.

After installing a new ECM, input the saved learning values and codes into the new ECM using the GTS (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).


c.

Turn the engine switch off and turn the GTS off.


d.

Wait for at least 30 seconds.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Clear DTC P062F stored in the ECM using the GTS (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR).

HINT:
·

Each injector assembly has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the injector compensation codes to balance the different fuel injections between each injector assembly.

·

When you first turn the engine switch on (IG) after replacing the ECM and other component(s), DTC P062F is stored. Manually clear the DTC upon completion of injector compensation code registration.

Replacement Part Utility Item
ECM
·

Learning Values Save (See page (Click here))

·

Learning Values Write (See page (Click here))


Exhaust pipe assembly (DPF catalytic converter)
·

Clear DPF Thermal Deterioration Data (See page (Click here))

·

Learning Values Write (See page (Click here))


Injector assembly
·

Input Injector Compensation Code (See page (Click here))

·

Pilot Quantity Learning (See page (Click here))







CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.LEARNING VALUES CONFIRMATION
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Engine and ECT / Utility / Learning values confirmation (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).

Result
Result Proceed to
The injector compensation codes are not input A
The injector compensation codes registered in the ECM are different than the codes imprinted on the injectors A
The pilot quantity learning values are set to the default values B
The catalyst deterioration learning values are set to the default values B
Except above C

HINT:
·

When the catalyst deterioration learning values are set to the default values, "FFFFFFFF" is displayed.

·

When the pilot quantity learning values are set to the default values, "7FFF" is displayed.





A

2.REGISTER INJECTOR COMPENSATION CODE

B

3.LEARNING VALUES WRITE

C

7.CHECK DTC OUTPUT
2.REGISTER INJECTOR COMPENSATION CODE
a.

Register the injector compensation code (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



NEXT

5.PILOT QUANTITY LEARNING
3.LEARNING VALUES WRITE
HINT:

When replacing the ECM, after performing "Learning Values Save" to save the learned values from the old ECM using the GTS and replacing the old ECM with a new one, "Learning Values Write" was not performed using the GTS causing this DTC to be output.


a.

Install the old ECM.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Engine and ECT / Utility / Learning values save (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).


e.

Remove the old ECM.


f.

Install a new ECM.


g.

Enter the following menus: Engine and ECT / Utility / Learning values write (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



NEXT

4.LEARNING VALUES CONFIRMATION
4.LEARNING VALUES CONFIRMATION
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Engine and ECT / Utility / Learning values confirmation (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).

Result
Result Proceed to
The pilot quantity learning values are set to the default values A
The catalyst deterioration learning values are set to the default values B
Except above C

HINT:
·

When the catalyst deterioration learning values are set to the default values, "FFFFFFFF" is displayed.

·

When the pilot quantity learning values are set to the default values, "7FFF" is displayed.





A

5.PILOT QUANTITY LEARNING

B

6.CATALYST RECORD CLEAR

C

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.PILOT QUANTITY LEARNING
a.

Perform the fuel injector pilot quantity learning (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



NEXT

7.CHECK DTC OUTPUT
6.CATALYST RECORD CLEAR

NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off and leave the vehicle for 30 seconds or more.


d.

Turn the engine switch on (IG) for 1 second.


e.

Enter the following menus: Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Result
Result Proceed to
P062F is output A
No DTC is output B



A

8.REPLACE ECM

B

END

8.REPLACE ECM

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off and leave the vehicle for 30 seconds or more.


d.

Turn the engine switch on (IG) for 1 second.


e.

Enter the following menus: Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END