Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P1626  Idle Signal Output Value Too Low  P1627  Idle Signal Output Value Too High  P1629  Idol Signal Output Value Too Low Bank2  P162A  Idol Signal Output Value Too High Bank2  


DESCRIPTION

The ECM reduces injector assembly operation speed and applied voltage to the injector assembly to reduce the sound it produces during idling. To do this, the ECM outputs applied voltage switching signals to terminal IJEN of the injector driver from terminal IDLO and IDL2 of the ECM.

P1626 (No. 1), P1629 (No. 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Warm up the engine and idle it for 5 seconds With the engine running at idle, voltage of the ECM IDLO or IDL2 terminal is 0.05 V or less for 5 seconds or more (1 trip detection logic).
·

Open or short in idle control circuit

·

Injector driver

·

ECM



P1627 (No. 1), P162A (No. 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Warm up the engine and idle it for 5 seconds With the engine running at speeds higher than idle, voltage of the ECM IDLO or IDL2 terminal is 3.4 V or higher for 5 seconds or more (1 trip detection logic).
·

Open or short in idle control circuit

·

Injector driver

·

ECM



WIRING DIAGRAM

A275257E01
5.889,2.225 6.873,2.395 0.984,0.170 10 C45*1, C46*2 6.169,2.422 6.528,2.586 0.359,0.165 10 ECM 5.889,0.522 6.290,0.671 0.401,0.149 10 IDLO 5.569,0.419 5.763,0.578 0.194,0.159 10 59 1.497,0.409 1.625,0.565 0.128,0.156 10 7 1.042,0.486 1.377,0.664 0.335,0.178 10 IJEN 0.579,1.163 2.307,1.326 1.728,0.163 10 No. 1 Injector Driver (EDU) 0.551,0.99 0.936,1.174 0.385,0.184 10 C152 5.88,1.825 6.281,1.974 0.401,0.149 10 IDL2 5.559,1.722 5.753,1.881 0.194,0.159 10 58 1.511,1.719 1.639,1.875 0.128,0.156 10 7 1.056,1.796 1.391,1.974 0.335,0.178 10 IDL2 0.565,2.499 2.293,2.661 1.728,0.163 10 No. 2 Injector Driver (EDU) 0.537,2.326 0.922,2.509 0.385,0.184 10 C156 3.176,2.039 3.970,2.213 0.795,0.174 10 *1: for LHD 3.176,2.319 3.975,2.484 0.799,0.165 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)
a.

Disconnect the No. 1 or No. 2 injector driver connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C152-7 (IJEN) - C45-59 (IDLO) Always Below 1 Ω
C156-7 (IDL2) - C45-58 (IDL2) Always Below 1 Ω
C152-7 (IJEN) or C45-59 (IDLO) - Body ground Always 10 kΩ or higher
C156-7 (IDL2) or C45-58 (IDL2) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C152-7 (IJEN) - C46-59 (IDLO) Always Below 1 Ω
C156-7 (IDL2) - C46-58 (IDL2) Always Below 1 Ω
C152-7 (IJEN) or C46-59 (IDLO) - Body ground Always 10 kΩ or higher
C156-7 (IDL2) or C46-58 (IDL2) - Body ground Always 10 kΩ or higher



d.

Reconnect the No. 1 or No. 2 injector driver connector.


e.

Reconnect the ECM connector.



OK

2.REPLACE INJECTOR DRIVER

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.REPLACE INJECTOR DRIVER
·

When DTC P1626 or P1627 is output:

Replace the No. 1 injector driver (See page Engine / Hybrid System>1VD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL).


·

When DTC P1629 or P162A is output:

Replace the No. 2 injector driver (See page Engine / Hybrid System>1VD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL).



NEXT

3.CHECK ANY OTHER DTCS OUTPUT
3.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
No DTC is output A
P1626 or P1627 is output B



A

END

B

4.REPLACE ECM
4.REPLACE ECM

NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

After warming up the engine, idle the engine for 5 seconds or more.


d.

Enter the following menus: Engine and ECT / Trouble Codes.


e.

Confirm that the DTC is not output again.



NEXT

END