The ECM reduces injector assembly operation speed and applied voltage to the injector assembly to reduce the sound it produces during idling. To do this, the ECM outputs applied voltage switching signals to terminal IJEN of the injector driver from terminal IDLO and IDL2 of the ECM.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Warm up the engine and idle it for 5 seconds | With the engine running at idle, voltage of the ECM IDLO or IDL2 terminal is 0.05 V or less for 5 seconds or more (1 trip detection logic). | ·
Open or short in idle control circuit ·
Injector driver ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Warm up the engine and idle it for 5 seconds | With the engine running at speeds higher than idle, voltage of the ECM IDLO or IDL2 terminal is 3.4 V or higher for 5 seconds or more (1 trip detection logic). | ·
Open or short in idle control circuit ·
Injector driver ·
ECM |
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the No. 1 or No. 2 injector driver connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C152-7 (IJEN) - C45-59 (IDLO) | Always | Below 1 Ω |
| C156-7 (IDL2) - C45-58 (IDL2) | Always | Below 1 Ω |
| C152-7 (IJEN) or C45-59 (IDLO) - Body ground | Always | 10 kΩ or higher |
| C156-7 (IDL2) or C45-58 (IDL2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C152-7 (IJEN) - C46-59 (IDLO) | Always | Below 1 Ω |
| C156-7 (IDL2) - C46-58 (IDL2) | Always | Below 1 Ω |
| C152-7 (IJEN) or C46-59 (IDLO) - Body ground | Always | 10 kΩ or higher |
| C156-7 (IDL2) or C46-58 (IDL2) - Body ground | Always | 10 kΩ or higher |
Reconnect the No. 1 or No. 2 injector driver connector.
Reconnect the ECM connector.
OK
NG
When DTC P1626 or P1627 is output:
Replace the No. 1 injector driver (See page Engine / Hybrid System>1VD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL).
When DTC P1629 or P162A is output:
Replace the No. 2 injector driver (See page Engine / Hybrid System>1VD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| P1626 or P1627 is output | B |
A
B
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR).
After warming up the engine, idle the engine for 5 seconds or more.
Enter the following menus: Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT