Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0115  Engine Coolant Temperature Circuit Malfunction  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor, whose resistance value varies according to the engine coolant temperature, is built into the engine coolant temperature sensor.

The structure of the sensor and its connection to the ECM are the same as those of the intake air temperature sensor.

HINT:

When DTC P0115, P0117 or P0118 is stored, the ECM enters fail-safe mode. During fail-safe mode, the engine coolant temperature is estimated to be 80°C (176°F) by the ECM. The ECM continues operating in fail-safe mode until a pass condition is detected.


DTC No. DTC Detection Condition Trouble Area
P0115 Open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


P0117 Short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


P0118 Open in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM



HINT:

When any of these DTCs is stored, check the engine coolant temperature by entering the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit

MONITOR DESCRIPTION

The engine coolant temperature sensor is used to monitor the engine coolant temperature. The engine coolant temperature sensor has a thermistor with a resistance that varies according to the temperature of the engine coolant. When the coolant temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are reflected in the output voltage from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the engine coolant temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a fault in the engine coolant temperature sensor and stores a DTC.

Example:

If the sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the engine coolant temperature sensor circuit and stores DTC P0118. Conversely, if the voltage output is below 0.14 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit and stores DTC P0117.

If the malfunction is not repaired successfully, a DTC is stored 0.5 seconds after the engine is next started.

WIRING DIAGRAM

A223345E05
0.801,1.979 3.099,2.140 2.297,0.161 10 Engine Coolant Temperature Sensor 0.805,1.825 1.079,1.973 0.274,0.148 10 C18 5.272,0.603 5.456,0.756 0.184,0.153 10 76 5.272,1.22 5.456,1.372 0.184,0.153 10 97 5.534,0.603 5.931,0.753 0.397,0.149 10 THW 5.531,1.229 5.987,1.386 0.456,0.157 10 ETHW 6.225,0.243 6.484,0.404 0.258,0.162 10 5 V 5.708,2.42 6.043,2.592 0.336,0.172 10 ECM 5.71,2.262 6.604,2.420 0.894,0.157 10 C45*1, C46*2 3.893,2.071 4.649,2.390 0.756,0.319 10 *1: for LHD *2: for RHD 2.433,0.597 2.540,0.751 0.107,0.153 10 2 2.433,1.235 2.540,1.388 0.107,0.153 10 1

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
P0115 is output A
P0117 is output B
P0118 is output C



A

2.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)

B

5.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

3.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
2.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


e.

Read the value displayed on the GTS.

Standard value:

Between 75°C and 100°C (167°F and 212°F) with warm engine


Result
Temperature Displayed Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
Between 75°C and 100°C (167°F and 212°F) C

HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).


·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





A

3.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

5.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

3.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
U163309E02
0.823,0.167 1.01,0.323 0.188,0.156 10 false *1 0.24,1.865 0.427,2.021 0.188,0.156 10 false *a 2.594,0.167 2.781,0.323 0.188,0.156 10 false *2 2.458,1.021 2.813,1.177 0.354,0.156 10 false THW 2.438,1.469 2.875,1.625 0.438,0.156 10 false ETHW 0.76,2.771 1.063,2.927 0.302,0.156 10 false C18

a.

Disconnect the engine coolant temperature sensor connector.


b.

Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


g.

Read the value displayed on the GTS.

Standard value:

140°C (284°F) or higher


Text in Illustration
*1 Engine Coolant Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor)



OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
4.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C18-2 - C45-76 (THW) Always Below 1 Ω
C18-1 - C45-97 (ETHW) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C18-2 - C46-76 (THW) Always Below 1 Ω
C18-1 - C46-97 (ETHW) Always Below 1 Ω




OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
A211723E12
0.698,0.125 0.906,0.302 0.208,0.177 10 false *1 2.542,0.125 2.75,0.302 0.208,0.177 10 false *2 2.427,1 2.948,1.177 0.521,0.177 10 false THW 2.417,1.448 2.938,1.625 0.521,0.177 10 false ETHW

a.

Disconnect the engine coolant temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


f.

Read the value displayed on the GTS.

Standard value:

-40°C (-40°F)


Text in Illustration
*1 Engine Coolant Temperature Sensor
*2 ECM



OK

NG

6.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
6.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C18-2 or C45-76 (THW) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C18-2 or C46-76 (THW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR