Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If signals which indicate the brake pedal is being depressed and released are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, the Data List items Stop Light Switch and ST1 are both ON when the brake pedal is depressed because the characteristics of ST1 indication are the opposite of the characteristics of Stop Light Switch indication.



DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a), (b) and (c) are met for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) STP signal is OFF when the ST1- signal is OFF.
·

Short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

A160611E25
1.167,0.885 2.24,1.094 1.073,0.208 10 false from IG2 Relay 1.219,1.865 2.24,2.104 1.021,0.24 10 false from ALT Fuse 2.792,0.708 3.104,0.865 0.313,0.156 10 false IGN 2.76,1.042 2.896,1.198 0.135,0.156 10 false 1 3.01,1.042 3.146,1.198 0.135,0.156 10 false 2 2.76,2.021 2.896,2.177 0.135,0.156 10 false 1 4.563,1.802 4.698,1.958 0.135,0.156 10 false 1 5.896,3.104 6.281,3.26 0.385,0.156 10 false ECM 3.01,2.021 3.146,2.177 0.135,0.156 10 false 2 3.438,1.802 3.573,1.958 0.135,0.156 10 false 2 4.563,0.813 4.698,0.969 0.135,0.156 10 false 3 5.333,0.813 5.531,0.969 0.198,0.156 10 false 35 5.333,1.792 5.531,1.948 0.198,0.156 10 false 36 5.615,0.813 5.958,0.969 0.344,0.156 10 false ST1- 5.615,1.792 5.958,1.948 0.344,0.156 10 false STP 3.438,0.813 3.573,0.969 0.135,0.156 10 false 4 2.74,1.708 3.146,1.865 0.406,0.156 10 false STOP 3.479,2.396 4.615,2.583 1.135,0.188 10 false Stop Light Switch 5.729,2.938 6.583,3.146 0.854,0.208 10 false A38*1, A52*2 3.469,2.208 3.833,2.396 0.365,0.188 10 false A30 1.615,2.74 2.635,2.979 1.021,0.24 10 false *1: for LHD 1.615,3.052 2.635,3.292 1.021,0.24 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch and ST1.

(e)

Check the Data List when the brake pedal is depressed and released.




Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF

PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
U163885E02
0.115,0.094 0.313,0.281 0.198,0.188 10 false *a 1.604,1.031 1.885,1.188 0.281,0.156 10 false A30

a.

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A30-2 - Body ground Always 11 to 14 V
A30-4 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK ECM (STP AND ST1- VOLTAGE)
U163721E02
1.875,3.646 2.583,3.427 true 1.792,3.656 2.583,4.375 true 1.771,0.281 1.969,0.448 0.198,0.167 10 false *b 0.219,0.281 0.427,0.469 0.208,0.188 10 false *a 0.271,2.281 0.427,2.479 0.156,0.198 10 false *c 2.635,3.344 3.24,3.521 0.604,0.177 10 false 36 (STP) 2.635,4.323 3.26,4.531 0.625,0.208 10 false 35 (ST1-) 1.135,2.677 1.427,2.854 0.292,0.177 10 false A38 1.833,2.677 2.125,2.854 0.292,0.177 10 false A52 1.5,2.688 1.677,2.833 0.177,0.146 10 false *A 2.208,2.677 2.385,2.823 0.177,0.146 10 false *B

a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Brake Pedal Operation Specified Condition
A38-35 (ST1-) - Body ground Released 7.5 to 14 V
Depressed 0 to 1.5 V
A38-36 (STP) - Body ground Released 0 to 1.5 V
Depressed 7.5 to 14 V

for RHD
Tester Connection Brake Pedal Operation Specified Condition
A52-35 (ST1-) - Body ground Released 7.5 to 14 V
Depressed 0 to 1.5 V
A52-36 (STP) - Body ground Released 0 to 1.5 V
Depressed 7.5 to 14 V


Text in Illustration
*A for LHD
*B for RHD
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR