Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power source allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0560 Open in the ECM backup power source circuit (1 trip detection logic).
·

Open in backup power source circuit

·

Battery

·

Battery terminals

·

EFI MAIN fuse

·

ECM



HINT:

If DTC P0560 is stored, the ECM becomes unable to store some DTCs. Also, all DTCs and some of the data stored in the ECM are cleared every time the ignition switch is turned off.


WIRING DIAGRAM

U162909E01
6.239,3.161 6.609,3.331 0.370,0.170 10 ECM 5.903,2.209 6.114,2.385 0.211,0.177 10 E1 5.917,1.172 6.302,1.335 0.385,0.163 10 BATT 5.575,1.006 5.869,1.175 0.295,0.170 10 A52 5.571,2.21 5.865,2.379 0.295,0.170 10 C46 5.658,0.836 5.772,0.992 0.114,0.156 10 1 5.625,2.041 5.815,2.189 0.191,0.149 10 81 5.289,2.041 5.479,2.189 0.191,0.149 10 81 3.865,1.144 4.518,1.317 0.652,0.173 10 EFI MAIN 0.859,2.979 1.335,3.163 0.475,0.184 10 Battery 5.237,1.006 5.514,1.175 0.277,0.170 10 A38 5.32,0.836 5.434,0.992 0.114,0.156 10 1 5.233,2.21 5.510,2.380 0.277,0.170 10 C45 5.294,1.182 5.460,1.335 0.166,0.152 10 *1 5.294,2.391 5.460,2.543 0.166,0.152 10 *1 5.619,1.182 5.786,1.335 0.166,0.152 10 *2 5.619,2.391 5.786,2.543 0.166,0.152 10 *2 4.431,3.07 5.166,3.393 0.736,0.323 10 *1: for LHD *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
a.

Disconnect the ECM connector.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
Battery positive terminal - A38-1 (BATT) Always Below 1 Ω
Battery positive terminal or A38-1 (BATT) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
Battery positive terminal - A52-1 (BATT) Always Below 1 Ω
Battery positive terminal or A52-1 (BATT) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the cable to the positive (+) battery terminal.



OK

2.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.




OK

3.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

3.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE BATTERY TERMINAL

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.



d.

Turn the ignition switch off and turn the GTS off.


e.

Start the engine and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
P0560 is output A
No DTC is output B



A

B