Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2017.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0550  Power Steering Pressure Sensor Circuit Malfunction  P0552  Power Steering Pressure Sensor Circuit Low Input  P0553  Power Steering Pressure Sensor Circuit High Input  


DESCRIPTION

The power steering oil pressure sensor is turned on when a power steering wheel load is generated by turning the steering wheel. The ECM regulates the engine idling speed according to the voltage output of the sensor.

DTC No. DTC Detection Condition Trouble Area
P0550 Power steering oil pressure sensor voltage is below 0.28 V, or higher than 4.9 V for 0.5 seconds while the engine is running (1 trip detection logic).
·

Open or short in power steering oil pressure sensor circuit

·

Power steering oil pressure sensor

·

ECM


P0552 Power steering oil pressure sensor voltage is below 0.28 V for 0.5 seconds while the engine is running (1 trip detection logic).
·

Open or short in power steering oil pressure sensor circuit

·

Power steering oil pressure sensor

·

ECM


P0553 Power steering oil pressure sensor voltage is higher than 4.9 V for 0.5 seconds while the engine is running (1 trip detection logic).
·

Open or short in power steering oil pressure sensor circuit

·

Power steering oil pressure sensor

·

ECM



MONITOR DESCRIPTION

The ECM monitors the power steering oil pressure sensor voltage and uses this value to regulate the engine idling speed. When the power steering oil pressure sensor output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure sensor and stores a DTC.

WIRING DIAGRAM

A162851E14
5.041,0.571 5.354,0.736 0.313,0.165 10 PSP 5.302,2.976 6.209,3.141 0.907,0.165 10 C45*1, C46*2 5.036,1.477 5.442,1.642 0.406,0.165 10 VCV2 1.903,0.571 2.216,0.736 0.313,0.165 10 PSP 1.985,1.481 2.215,1.646 0.230,0.165 10 VC 5.041,2.392 5.503,2.548 0.462,0.156 10 ETHW 5.302,3.14 5.662,3.314 0.360,0.174 10 ECM 4.783,0.482 4.967,0.638 0.184,0.156 10 72 4.783,1.378 4.967,1.534 0.184,0.156 10 66 4.783,2.303 4.967,2.459 0.184,0.156 10 97 2.318,0.473 2.446,0.629 0.128,0.156 10 2 2.304,1.393 2.414,1.554 0.110,0.161 10 1 2.304,2.299 2.423,2.455 0.119,0.156 10 3 2.002,2.399 2.206,2.548 0.205,0.149 10 E2 0.503,2.96 0.805,3.123 0.302,0.163 10 C59 0.503,3.121 2.798,3.291 2.295,0.170 10 Power Steering Oil Pressure Sensor 3.519,2.925 4.393,3.303 0.873,0.378 12 *1: for LHD *2: for RHD

CAUTION / NOTICE / HINT

HINT:
·

If DTCs relating to different systems which share terminal E2 as their ground are stored simultaneously, there may be an open circuit between terminal E2 and ground.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the power steering oil pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C59-2 (PSP) - C45-72 (PSP) Always Below 1 Ω
C59-1 (VC) - C45-66 (VCV2) Always Below 1 Ω
C59-3 (E2) - C45-97 (ETHW) Always Below 1 Ω
C59-2 (PSP) or C45-72 (PSP) - Body ground Always 10 kΩ or higher
C59-1 (VC) or C45-66 (VCV2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C59-2 (PSP) - C46-72 (PSP) Always Below 1 Ω
C59-1 (VC) - C46-66 (VCV2) Always Below 1 Ω
C59-3 (E2) - C46-97 (ETHW) Always Below 1 Ω
C59-2 (PSP) or C46-72 (PSP) - Body ground Always 10 kΩ or higher
C59-1 (VC) or C46-66 (VCV2) - Body ground Always 10 kΩ or higher




OK

2.REPLACE POWER STEERING OIL PRESSURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE POWER STEERING OIL PRESSURE SENSOR
a.

Replace the power steering oil pressure sensor (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>POWER STEERING OIL PRESSURE SWITCH>REMOVAL).



NEXT

3.CONFIRM WHETHER DTC OUTPUT RECURS
3.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Idle the engine for 5 seconds.


f.

Read the DTCs.

Result
Result Proceed to
P0550, P0552 and/or P0553 is output A
No DTC is output B



A

B

END