Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2610  ECM / PCM Internal Engine Off Timer Performance  


DTC SUMMARY

DTC No. Monitoring Item Malfunction Detection Condition Trouble Area Detection Timing Detection Logic
P2610 Soak timer (built into ECM) There is an ECM internal malfunction (2 trip detection logic). ECM Engine running 2 trip

DESCRIPTION

The soak timer operates after the ignition switch is turned off. When a certain amount of time has elapsed after turning the ignition switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

A256707E12
3.563,1.135 4.615,1.354 1.052,0.219 10 false ENG-IG2 NO. 1 4.281,0.865 4.719,1.104 0.438,0.24 10 false IGSW 5.604,4.25 6,4.5 0.396,0.25 10 false ECM 4.302,3.479 4.75,3.75 0.448,0.271 10 false MREL 4.469,2.667 4.75,2.917 0.281,0.25 10 false +B 5,1.24 5.75,1.615 0.75,0.375 10 false Soak Timer IC 4.99,2.552 5.646,2.958 0.656,0.406 10 false Power Source IC 4.969,3.354 5.729,3.75 0.76,0.396 10 false MAIN Relay Control IC 2.74,1.708 3.469,1.979 0.729,0.271 10 false IG2 MAIN 1.719,3.313 2.781,3.542 1.063,0.229 10 false EFI MAIN NO. 1 0.635,0.969 1.49,1.208 0.854,0.24 10 false from Battery 0.594,3.177 1.417,3.417 0.823,0.24 10 false from Battery 0.76,2.156 4.073,2.542 3.313,0.385 10 false from Certification ECU (Smart Key ECU Assembly)*1 or Ignition Switch*2 0.063,0.063 2.156,0.385 2.094,0.323 10 false Reference (System Diagram): 2.563,3.906 3.625,4.135 1.063,0.229 10 false EFI MAIN NO. 1 0.083,3.99 2.042,4.531 1.958,0.542 10 false *1: w/ Entry and Start System *2: w/o Entry and Start System

MONITOR DESCRIPTION

1.

While the engine is running, the ECM monitors the synchronization of the soak timer and CPU clock. If these two are not synchronized, the ECM interprets this as a malfunction, illuminates the MIL and stores the DTC.

2.

If the soak timer activates the ECM even though only a short amount of time has elapsed since the ignition switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the ignition switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the ignition switch is turned to ON.


CAUTION / NOTICE / HINT

HINT:
·

DTC P2610 is stored if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is necessary.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

NEXT

2.CHECK WHETHER DTC OUTPUT RECURS
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Start the engine and wait for 10 minutes or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

If no pending DTC is output, the repair has been successfully completed.



NEXT

END