Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › RELAY › from 2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255031 RELAY G

3UR-FE ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT MAIN BODY ECU

U155732E05
2.094,2.448 2.26,2.625 0.167,0.177 10 false 2J 4.427,0.25 4.615,0.427 0.188,0.177 10 false 2K 2.792,0.24 2.99,0.417 0.198,0.177 10 false 2H 1.677,0.24 1.875,0.417 0.198,0.177 10 false 2G 1.094,0.24 1.271,0.417 0.177,0.177 10 false 2F 3.958,2.438 4.115,2.615 0.156,0.177 10 false 2I 0.063,0.01 0.302,0.25 0.24,0.24 10 false *a

Text in Illustration
*a Component without harness connected
(Main Body ECU)
- -

NOTICE:
·

The IG1 No. 1 relay, IG1 No. 2 relay and IG1 No. 3 relay are built into the main body ECU.

·

Before performing the relay inspections for the relays of the main body ECU, inspect the ECU-IG No. 1, ECU-IG No. 2 and ECU-IG No. 3 fuses.



a.

Inspect the IG1 No. 1 relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2G-1 - 2H-24 Battery voltage is not applied to terminals 2I-18 and 2J-1 10 kΩ or higher
Battery voltage is applied to terminals 2I-18 and 2J-1 Below 1 Ω


If the result is not as specified, replace the main body ECU.



b.

Inspect the IG1 No. 2 relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2G-1 - 2H-14 Battery voltage is not applied to terminals 2I-18 and 2J-1 10 kΩ or higher
Battery voltage is applied to terminals 2I-18 and 2J-1 Below 1 Ω


If the result is not as specified, replace the main body ECU.



c.

Inspect the IG1 No. 3 relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2G-1 - 2H-16 Battery voltage is not applied to terminals 2I-18 and 2J-1 10 kΩ or higher
Battery voltage is applied to terminals 2I-18 and 2J-1 Below 1 Ω


If the result is not as specified, replace the main body ECU.



Hide 2.INSPECT AIR INJECTION VSV RELAY (AI-VSV)

a.
A184106E13
2.542,1.104 2.938,1.104 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 3.INSPECT INTEGRATION RELAY

U163817E02
1.771,0.76 1.969,0.938 0.198,0.177 10 false 1P 3.573,0.771 3.781,0.948 0.208,0.177 10 false 1R 2.521,0.76 2.719,0.938 0.198,0.177 10 false 1Q 4.344,0.771 4.542,0.948 0.198,0.177 10 false 1S 5.396,0.771 5.604,0.948 0.208,0.177 10 false 1Y 0.083,0.021 0.302,0.229 0.219,0.208 10 false *a

Text in Illustration
*a Component without harness connected
(Integration Relay)
- -

NOTICE:
·

The IG2 MAIN relay, FUEL PMP relay, EFI MAIN No. 1 relay, A/F relay and AIR PMP HTR relay are built into the integration relay.

·

Before performing the relay inspections for the relays of the integration relay, inspect the IG2 MAIN, FUEL PMP, EFI No. 2, EFI MAIN No. 1, A/F HTR and AIR PMP HTR fuses.



a.

Inspect the IG2 MAIN relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1Y-1 - 1R-1 Battery voltage is not applied to terminals 1R-2 and 1S-4 10 kΩ or higher
Battery voltage is applied to terminals 1R-2 and 1S-4 Below 1 Ω


If the result is not as specified, replace the integration relay.



b.

Inspect the FUEL PMP relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1Y-1 - 1R-6 Battery voltage is not applied to terminals 1R-7 and 1S-12 10 kΩ or higher
Battery voltage is applied to terminals 1R-7 and 1S-12 Below 1 Ω


If the result is not as specified, replace the integration relay.



c.

Inspect the EFI MAIN No. 1 relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1Y-1 - 1S-1 Battery voltage is not applied to terminals 1S-8 and 1S-4 10 kΩ or higher
Battery voltage is applied to terminals 1S-8 and 1S-4 Below 1 Ω


If the result is not as specified, replace the integration relay.



d.

Inspect the A/F relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1Y-1 - 1S-3 Battery voltage is not applied to terminals 1S-1 and 1S-4 10 kΩ or higher
Battery voltage is applied to terminals 1S-1 and 1S-4 Below 1 Ω


If the result is not as specified, replace the integration relay.



e.

Inspect the AIR PMP HTR relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1Y-1 - 1P-9 Battery voltage is not applied to terminals 1Y-1 and 1P-10 10 kΩ or higher


Standard Voltage:
Tester Connection Condition Specified Condition
1P-9 - Battery negative (-) Battery positive (+) → 1Y-1
Battery negative (-) → 1P-10
11 to 14 V


If the result is not as specified, replace the integration relay.