Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › from 2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM(w/o Secondary Air Injection System) C

3UR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  P1340  Camshaft Position Sensor "A" (Bank 1 Sensor 2)  P1342  Camshaft Position Sensor "A" Low Input (MRE)  P1343  Camshaft Position Sensor "A" High Input (MRE)  


DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet and MRE (Magnetic Resistance Element).

The camshaft drive gear (LH) has 3 teeth on its inner circumference. When the camshaft gear rotates, air gap changes between the protrusion on the teeth and the MRE. The change affects the magnetic field and results in changes in the resistance of the MRE.

The crankshaft position sensor plate has 34 teeth and is installed to the rear end of the crankshaft. The crankshaft position sensor generates 34 signals with every revolution. The ECM detects the standard crankshaft angle based on the G signal, and the actual crankshaft angle and engine speed by the NE signal.

DTC Code DTC Detection Condition Trouble Area
P1340 No camshaft position sensor signal is sent to the ECM during cranking (2 trip detection logic).
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Camshaft timing plate LH

·

ECM


No camshaft position sensor signal is sent to the ECM with an engine speed of 600 rpm or more.
P1342 The output voltage of the camshaft position sensor is below 0.3 V for 4 seconds (1 trip detection logic).
P1343 The output voltage of the camshaft position sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).

MONITOR DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet and MRE.

The camshaft drive gear has 3 teeth on its inner circumference. When the camshaft gear rotates, air gap changes between the protrusion on the gear and the MRE. The change affects the magnetic field and results in changes in the resistance of the MRE. The crankshaft position sensor plate has 34 teeth and outputs 34 signals with every revolution. The ECM detects the standard crankshaft angle based on the G signal, and the actual crankshaft angle and engine speed by the NE signal.

WIRING DIAGRAM

A165785E07
5.311,0.997 5.710,1.153 0.399,0.156 10 VCV2 5.311,1.543 5.660,1.714 0.349,0.170 10 G2+ 5.311,2.086 5.762,2.274 0.451,0.188 10 VV1- 4.964,0.923 5.228,1.079 0.265,0.156 10 110 5.038,1.46 5.229,1.616 0.191,0.156 10 89 5.038,1.997 5.229,2.153 0.191,0.156 10 88 2.441,0.998 2.670,1.150 0.230,0.151 10 VC 2.441,1.541 2.670,1.692 0.230,0.151 10 G2 2.441,2.078 2.670,2.229 0.230,0.151 10 G- 2.745,0.918 2.887,1.073 0.142,0.155 10 3 2.745,1.455 2.887,1.610 0.142,0.155 10 1 2.745,1.992 2.887,2.147 0.142,0.155 10 2 5.513,2.623 5.867,2.779 0.355,0.156 10 C45 5.513,2.763 5.854,2.919 0.341,0.156 10 ECM 1.329,2.354 1.675,2.510 0.346,0.156 10 C99 1.329,2.494 2.981,2.660 1.651,0.165 10 Camshaft Position Sensor

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT CAMSHAFT POSITION SENSOR (SENSOR POWER SOURCE)
U163402E01
0.328,0.049 2.697,0.441 2.369,0.392 10 Front view of wire harness connector: (to Camshaft Position Sensor) 0.294,2.06 0.598,2.239 0.304,0.179 10 C99 2.815,2.816 3.054,2.995 0.239,0.179 10 VC 2.064,2.18 2.763,2.885 false

a.

Disconnect the C99 camshaft position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C99-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.0 V




OK

2.CHECK HARNESS AND CONNECTOR (ECM - CAMSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ECM - CAMSHAFT POSITION SENSOR)
a.

Disconnect the C99 camshaft position sensor connector.


b.

Disconnect the C45 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C99-1 (G2) - C45-89 (G2+) Always Below 1 Ω
C99-2 (G-) - C45-88 (VV1-) Always Below 1 Ω
C99-1 (G2) or C45-89 (G2+) - Body ground Always 10 kΩ or higher
C99-2 (G-) or C45-88 (VV1-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT SENSOR INSTALLATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SENSOR INSTALLATION
A385403E02
0.49,1.781 0.802,1.979 0.313,0.198 10 false OK 1.688,1.552 2.354,1.771 0.667,0.219 10 false Clearance 2.646,1.781 2.958,1.979 0.313,0.198 10 false NG

a.

Check the camshaft position sensor installation.

OK:

The camshaft position sensor is installed properly.




OK

4.INSPECT CAMSHAFT TIMING PLATE (SIGNAL PLATE TOOTH)

NG

4.INSPECT CAMSHAFT TIMING PLATE (SIGNAL PLATE TOOTH)
a.

Check the teeth of the signal plate.

OK:

Sensor plate teeth do not have any cracks or deformation.




OK

5.REPLACE CAMSHAFT POSITION SENSOR

NG

5.REPLACE CAMSHAFT POSITION SENSOR
a.


NEXT

6.CONFIRM WHETHER DTC OUTPUT RECURS
6.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.


g.

Read DTCs.

Result
Result Proceed to
No DTC is output A
P1340, P1342 and/or P1343 are output B

HINT:

If the engine does not start, replace the ECM.




A

END

B