Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › from 2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the engine switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC Code DTC Detection Condition Trouble Area
P0560 An open in the ECM back up power source circuit (1 trip detection logic).
·

Open in back up power source circuit

·

Battery

·

Battery terminals

·

EFI MAIN fuse

·

ECM



HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.


WIRING DIAGRAM

A290248E11
5.573,0.708 6.031,0.906 0.458,0.198 10 false A38 5.573,1.292 6.031,1.49 0.458,0.198 10 false C45 3.615,0.885 4.656,1.219 1.042,0.333 10 false EFI MAIN NO. 1 5.885,1.333 6.344,1.531 0.458,0.198 10 false E1 5.656,0.542 6.115,0.74 0.458,0.198 10 false 1 5.615,1.125 6.073,1.323 0.458,0.198 10 false 81 2.208,0.896 2.906,1.115 0.698,0.219 10 false P/I-B 0.969,1.833 1.667,2.052 0.698,0.219 10 false Battery 5.896,0.729 6.354,0.927 0.458,0.198 10 false BATT

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT BATTERY
a.

Check that the battery is not depleted (See page Power Source / Network>3UR-FE (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION).

OK:

Battery is not depleted.




OK

2.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

2.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

3.INSPECT ECM (BATT VOLTAGE)

NG

REPAIR BATTERY TERMINAL

3.INSPECT ECM (BATT VOLTAGE)
U163313E01
0.32,1.209 0.587,1.372 0.267,0.163 10 A38 0.32,1.209 0.587,1.372 0.267,0.163 10 A38 1.842,1.852 2.591,2.015 0.748,0.163 10 1 (BATT) 0.045,0.008 2.421,0.448 2.376,0.440 10 Front view of wire harness connector: (to ECM) 1.495,1.053 1.809,1.902 false

a.

Disconnect the A38 ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-1 (BATT) - Body ground Always 11 to 14 V




OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.



d.

Turn the engine switch off and turn the tester off.


e.

Start the engine and turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.


g.

Read DTCs.

Result
Result Proceed to
P0560 is output A
No DTC is output B



A

B