Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › from 2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P2118  Throttle Actuator Control Motor Current Range / Performance  


DESCRIPTION

The ETCS (Electronic Throttle Control System) has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (below 4 V), the ECM determines that there is a malfunction in the ETCS and cuts off the current to the throttle actuator.

When the voltage becomes unstable, the ETCS itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the engine switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.

HINT:

The ETCS does not use a throttle cable.


A385736E03
0.125,0.094 2.5,0.385 2.375,0.292 12 false Reference (System Diagram): 0.115,0.833 0.854,1.396 0.74,0.563 10 false from EFI MAIN NO. 1 Relay 0.323,1.792 0.938,2.448 0.615,0.656 10 false from Battery 1.188,2 2.052,2.219 0.865,0.219 10 false ETCS 4.729,0.958 5,1.146 0.271,0.188 10 false +B 4.729,1.729 5.115,1.917 0.385,0.188 10 false +BM 4.729,2.448 5.115,2.635 0.385,0.188 10 false M+ 4.729,3.115 5.115,3.302 0.385,0.188 10 false M- 4.74,3.792 5.24,3.969 0.5,0.177 10 false ME01 0.823,3.563 1.865,3.771 1.042,0.208 10 false Throttle Actuator 5.906,0.781 6.458,1.677 0.552,0.896 10 false Power Source Circuit for CPU 5.927,2.458 6.771,3.229 0.844,0.771 10 false Throttle Actuator Control Circuit 5.604,4.25 6.104,4.427 0.5,0.177 10 false ECM

DTC Code DTC Detection Condition Trouble Area
P2118 An open in the ETCS power source (+BM) circuit (1 trip detection logic).
·

Open in ETCS power source circuit

·

ETCS fuse

·

ECM



MONITOR DESCRIPTION

The ECM monitors the battery supply voltage applied to the throttle actuator.

When the power supply voltage (+BM) drops below 4 V for 0.8 seconds or more, the ECM interprets this as an open in the power supply circuit (+BM). The ECM illuminates the MIL and stores the DTC.

If the malfunction is not repaired successfully, the DTC is stored 5 seconds after the engine is next started.

FAIL-SAFE

When this DTC, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the engine switch is then turned off.

WIRING DIAGRAM

A162854E17
5.767,4.841 6.131,5.000 0.364,0.159 10 ECM 5.508,1.642 6.581,1.992 1.073,0.350 10 Throttle Actuator Control Circuit 5.005,0.752 5.356,0.908 0.350,0.156 10 +BM 5.019,1.397 5.258,1.566 0.239,0.170 10 M+ 5.019,2.244 5.258,2.414 0.239,0.170 10 M- 5.009,2.962 5.387,3.117 0.378,0.156 10 GE01 5.019,3.526 5.231,3.682 0.211,0.156 10 E1 5.019,4.016 5.418,4.179 0.399,0.163 10 ME01 5.767,4.691 6.097,4.847 0.331,0.156 10 C45 4.66,0.727 4.950,0.888 0.290,0.161 10 104 4.749,3.417 4.974,3.577 0.225,0.161 10 81 4.749,3.914 4.970,4.075 0.221,0.161 10 18 4.74,1.391 4.965,1.546 0.225,0.156 10 20 4.74,2.222 4.979,2.378 0.239,0.156 10 19 4.74,2.857 4.965,3.013 0.225,0.156 10 42 3.891,2.679 4.464,2.844 0.573,0.165 10 Shielded 2.813,1.385 2.931,1.541 0.119,0.156 10 2 2.813,2.235 2.931,2.391 0.119,0.156 10 1 1.832,2.725 2.053,2.881 0.221,0.156 10 C3 1.832,2.865 2.895,3.040 1.063,0.174 10 Throttle Actuator 1.131,0.962 1.546,1.128 0.415,0.165 10 ETCS 0.599,4.079 1.162,4.263 0.563,0.184 10 Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (+BM VOLTAGE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / +BM voltage.


d.

Read the value displayed on the tester.

Standard Voltage:

11 to 14 V




OK

NG

2.INSPECT ECM (+BM VOLTAGE)
2.INSPECT ECM (+BM VOLTAGE)
U163769E02
1.646,2.75 2.021,2.167 true 2.052,2 2.563,2.719 true 2.042,1.542 1.885,1.021 1.885,1.021 1.781,1.021 true 0.115,0.042 2.51,0.479 2.396,0.438 10 false Front view of wire harness connector: (to ECM) 0.229,0.917 0.594,1.104 0.365,0.188 10 false C45 2.365,2.771 2.938,2.979 0.573,0.208 10 false 81 (E1) 1.26,2.781 1.969,2.99 0.708,0.208 10 false 104 (+BM) 1.115,0.917 1.875,1.125 0.76,0.208 10 false 18 (ME01)

a.

Disconnect the C45 ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C45-104 (+BM) - C45-81 (E1) Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-18 (ME01) - Body ground Always Below 1 Ω
C45-81 (E1) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR