Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › from 2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM(w/o Secondary Air Injection System) C

3UR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  P0365  Camshaft Position Sensor "B" Circuit (Bank 1)  P0367  Camshaft Position Sensor "B" Circuit Low Input (Bank 1)  P0368  Camshaft Position Sensor "B" Circuit High Input (Bank 1)  P0390  Camshaft Position Sensor "B" Circuit (Bank 2)  P0392  Camshaft Position Sensor "B" Circuit Low Input (Bank 2)  P0393  Camshaft Position Sensor "B" Circuit High Input (Bank 2)  


DESCRIPTION

The exhaust camshaft Variable Valve Timing (VVT) sensor (EV1, 2 signal) consists of a magnet and MRE (Magnetic Resistance Element).

The exhaust camshaft has a sensor plate with 3 teeth on its outer circumference. When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnet. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

DTC Code DTC Detection Condition Trouble Area
P0365
P0390
When either condition below is met:
·

The input voltage to the ECM remains at below 0.3 V or higher than 4.7 V for more than 4 seconds when 2 or more seconds have elapsed after turning the engine switch on (IG) (1 trip detection logic).

·

No VVT sensor signal is sent to the ECM during cranking (1 trip detection logic).


·

Open or short in VVT sensor (for exhaust side) circuit

·

VVT sensor (for exhaust side)

·

Exhaust camshaft

·

Jumped tooth of timing chain

·

ECM


P0367
P0392
The output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust side) circuit

·

VVT sensor (for exhaust side)

·

Exhaust camshaft

·

Jumped tooth of timing chain

·

ECM


P0368
P0393
The output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust side) circuit

·

VVT sensor (for exhaust side)

·

Exhaust camshaft

·

Jumped tooth of timing chain

·

ECM



A149747E02
0.201,1.21 0.431,1.375 0.230,0.165 10 NE 0.128,1.696 0.432,1.848 0.304,0.151 10 EV1 0.132,2.078 0.432,2.224 0.299,0.145 10 EV2 2.839,1.272 3.175,1.421 0.336,0.149 10 GND 2.839,2.226 3.175,2.375 0.336,0.149 10 GND 2.839,1.844 3.175,1.993 0.336,0.149 10 GND 1.056,2.555 1.977,2.696 0.921,0.141 10 20 msec./DIV. 2.635,0.687 3.199,0.843 0.563,0.156 10 5 V/DIV. 0.221,0.165 2.528,0.343 2.308,0.178 10 EV1, EV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope.

Standard:
Tester Connection Tool Setting Condition Specified Condition
C45-66 (NE+) - C45-65 (NE-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
C45-90 (EV1+) - C45-88 (VV1-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
C45-113 (EV2+) - C45-111 (VV2-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown


HINT:

EV1+ and EV2+ stand for the VVT sensor (for exhaust side) signal, and NE+ stands for the CKP sensor signal.



MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

WIRING DIAGRAM

A179606E14
0.468,3.898 0.839,4.075 0.371,0.177 10 C122 0.468,2.401 3.200,2.656 2.733,0.255 10 VVT Sensor for Exhaust Side (for Bank 1) 0.468,2.246 0.888,2.423 0.420,0.177 10 C121 0.468,4.054 3.277,4.341 2.809,0.288 10 VVT Sensor for Exhaust Side (for Bank 2) 1.436,1.196 1.744,1.349 0.308,0.152 10 VC2 1.436,2.857 1.744,3.009 0.308,0.152 10 VC2 1.856,1.119 1.998,1.296 0.142,0.177 10 3 4.779,1.105 5.116,1.282 0.338,0.177 10 110 4.843,1.487 5.079,1.664 0.236,0.177 10 90 4.843,1.87 5.079,2.046 0.236,0.177 10 88 1.422,1.582 1.747,1.734 0.326,0.152 10 EX+ 1.856,1.505 1.998,1.681 0.142,0.177 10 1 1.443,1.946 1.744,2.098 0.301,0.152 10 EX- 1.422,3.242 1.747,3.394 0.326,0.152 10 EX+ 1.443,3.606 1.744,3.759 0.301,0.152 10 EX- 5.135,1.198 5.708,1.393 0.573,0.195 10 VCV2 4.839,2.759 5.075,2.936 0.236,0.177 10 87 5.135,2.854 5.680,3.074 0.545,0.220 10 VCV1 5.135,1.584 5.565,1.795 0.430,0.210 10 EV1+ 5.135,1.948 5.569,2.140 0.434,0.192 10 VV1- 4.778,3.135 5.134,3.312 0.356,0.177 10 113 4.778,3.518 5.134,3.695 0.356,0.177 10 111 5.135,3.246 5.584,3.440 0.448,0.193 10 EV2+ 5.135,3.61 5.597,3.802 0.462,0.192 10 VV2- 1.856,1.869 1.998,2.046 0.142,0.177 10 2 1.856,2.751 1.998,2.928 0.142,0.177 10 3 1.856,3.137 1.998,3.313 0.142,0.177 10 1 1.856,3.501 1.998,3.678 0.142,0.177 10 2 5.614,4.26 5.919,4.416 0.305,0.156 10 C45 5.614,4.424 5.982,4.580 0.368,0.156 10 ECM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
a.
U163405E01
0.248,0.077 2.640,0.455 2.392,0.378 10 Front view of wire harness connector: (to VVT Sensor) 0.274,1.607 0.634,1.763 0.361,0.156 10 C121 0.274,1.938 0.634,2.094 0.361,0.156 10 C122 0.136,2.677 1.018,2.861 0.882,0.184 10 *1: for Bank 1 0.136,2.943 1.039,3.127 0.902,0.184 10 *2: for Bank 2 0.746,1.538 0.933,1.694 0.187,0.156 10 *1 0.746,1.869 0.947,2.046 0.201,0.177 10 *2 2.59,2.78 2.926,2.939 0.336,0.159 10 VC2 2.014,2.183 2.547,2.862 false

Disconnect the C121 or C122 VVT sensor (for exhaust side) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C121-3 (VC2) - Body ground Engine switch on (IG) 4.5 to 5.0 V
C122-3 (VC2) - Body ground Engine switch on (IG) 4.5 to 5.0 V




OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (for Exhaust Side) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (for Exhaust Side) - ECM)
a.

Disconnect the C121 or C122 VVT (for exhaust side) sensor connector.


b.

Disconnect the C45 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C121-1 (EX+) - C45-90 (EV1+) Always Below 1 Ω
C121-2 (EX-) - C45-88 (VV1-) Always Below 1 Ω
C122-1 (EX+) - C45-113 (EV2+) Always Below 1 Ω
C122-2 (EX-) - C45-111 (VV2-) Always Below 1 Ω
C121-1 (EX+) or C45-90 (EV1+) - Body ground Always 10 kΩ or higher
C121-2 (EX-) or C45-88 (VV1-) - Body ground Always 10 kΩ or higher
C122-1 (EX+) or C45-113 (EV2+) - Body ground Always 10 kΩ or higher
C122-2 (EX-) or C45-111 (VV2-) - Body ground Always 10 kΩ or higher




OK

3.CHECK SENSOR INSTALLATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION
a.
A385403E02
0.49,1.781 0.802,1.979 0.313,0.198 10 false OK 1.688,1.552 2.354,1.771 0.667,0.219 10 false Clearance 2.646,1.781 2.958,1.979 0.313,0.198 10 false NG

Check the VVT sensor (for exhaust side) installation.

OK:

Sensor is installed correctly.




OK

4.CHECK EXHAUST CAMSHAFT

NG

4.CHECK EXHAUST CAMSHAFT
a.

Check the teeth of the camshaft.

OK:

Teeth do not have any cracks or deformation.




OK

5.REPLACE VVT SENSOR (for Exhaust Side)

NG

5.REPLACE VVT SENSOR (for Exhaust Side)
a.

Replace the VVT sensor (for exhaust side) (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL).



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.


g.

Read DTCs.

Result
Result Proceed to
No output A
P0365, P0367, P0368, P0390, P0392 or P0393 B

HINT:

If the engine does not start, replace the ECM.




A

END

B