Home › Engine / Hybrid System › 1UR-FE (ENGINE MECHANICAL) › CYLINDER HEAD › 2014.08–2016.08
RM2660E _51 Engine / Hybrid System _052776 1UR-FE ENGINE MECHANICAL _0255041 CYLINDER HEAD A

1UR-FE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

NOTICE:
A384519N01
2.927,1.292 3.188,1.531 0.26,0.24 10 true (A)

The standard protrusion amount (A) of the valve guide bush determines whether the cylinder head is type A or B. Therefore, measure the standard protrusion amount (A) before removing the valve guide bush.


Standard Protrusion Height (A):
Type Specified Condition
Cylinder Head Type A 14.3 to 14.7 mm (0.563 to 0.579 in.)
Cylinder Head Type B 15.8 to 16.2 mm (0.622 to 0.638 in.)


a.

Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A164331E03
1.96,0.1 2.284,0.248 0.324,0.148 10 SST 1.912,0.183 1.802,0.183 1.802,0.183 1.536,0.675 false 0.961,1.88 1.285,2.027 0.324,0.148 10 SST 1.131,1.849 1.131,1.739 1.131,1.739 1.588,1.101 false

Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard Bush Bore Diameter:
Item Specified Condition
STD 10.285 to 10.306 mm (0.4049 to 0.4057 in.)
O/S 0.05 10.335 to 10.356 mm (0.4069 to 0.4077 in.)



e.

Select a new valve guide bush.

New Guide Bush:
Item Specified Condition
Bush Bore Diameter 10.285 to 10.306 mm (0.4049 to 0.4057 in.) 10.335 to 10.356 mm (0.4069 to 0.4077 in.)
Bush to be Used STD O/S 0.05


If the bush bore diameter of the cylinder head is more than 10.306 mm (0.406 in.), machine the bush bore diameter to between 10.335 and 10.356 mm (0.4069 and 0.4077 in.).

If the bush bore diameter of the cylinder head is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.

New Guide Bush Diameter:
Item Bush Diameter
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


HINT:

Standard bush length: 41.3 to 41.7 mm (1.63 to 1.64 in.)



f.
A164332E15
1.521,0.677 1.844,0.135 1.844,0.135 1.583,1.115 true 1.885,0.052 2.24,0.219 0.354,0.167 10 false SST 2.979,1.271 3.26,1.521 0.281,0.25 10 true (A)

Using SST and a hammer, tap in a new guide bush to the standard protrusion height (A).

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

14.3 to 14.7 mm (0.563 to 0.579 in.)


Standard Protrusion Height (A):
Type Specified Condition
Cylinder Head Type A 14.3 to 14.7 mm (0.563 to 0.579 in.)
Cylinder Head Type B 15.8 to 16.2 mm (0.622 to 0.638 in.)


NOTICE:

Install the valve guide bush after determining cylinder head type A and B.



g.
A164333

Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard oil clearance between the intake valve guide bush and intake valve stem.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

NOTICE:
A384519N01
2.927,1.292 3.188,1.531 0.26,0.24 10 true (A)

The standard protrusion amount (A) of the valve guide bush determines whether the cylinder head is type A or B. Therefore, measure the standard protrusion amount (A) before removing the valve guide bush.


Standard Protrusion Height (A):
Type Specified Condition
Cylinder Head Type A 14.3 to 14.7 mm (0.563 to 0.579 in.)
Cylinder Head Type B 15.8 to 16.2 mm (0.622 to 0.638 in.)


a.

Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A164334E07
2,1.281 2.906,1.281 true 2.042,1.094 2.781,1.094 2.781,1.094 2.781,1.281 true 2.948,1.198 3.385,1.51 0.438,0.313 10 true SST

Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard Bush Bore Diameter:
Item Specified Condition
STD 10.285 to 10.306 mm (0.4049 to 0.4057 in.)
O/S 0.05 10.335 to 10.356 mm (0.4069 to 0.4077 in.)



e.

Select a new exhaust valve guide bush.

New Guide Bush:
Item Specified Condition
Bush Bore Diameter 10.285 to 10.306 mm (0.4049 to 0.4057 in.) 10.335 to 10.356 mm (0.4069 to 0.4077 in.)
Bush to be Used STD O/S 0.05


If the bush bore diameter of the cylinder head is more than 10.306 mm (0.406 in.), machine the bush bore diameter to between 10.335 and 10.356 mm (0.4069 and 0.4077 in.).

If the bush bore diameter of the cylinder head is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.

New Guide Bush Diameter:
Item Bush Diameter
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


HINT:

Standard bush length: 46.8 to 47.2 mm (1.84 to 1.86 in.)



f.
A164335E15
2.031,1.063 2.948,1.521 2.948,1.521 2,1.302 true 3,1.438 3.313,1.594 0.313,0.156 10 false SST 0.177,1.313 0.427,1.573 0.25,0.26 10 true (A)

Using SST and a hammer, tap in a new guide bush to the standard protrusion height (A).

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height (A):
Type Specified Condition
Cylinder Head Type A 14.3 to 14.7 mm (0.563 to 0.579 in.)
Cylinder Head Type B 15.8 to 16.2 mm (0.622 to 0.638 in.)


NOTICE:

Install the valve guide bush after determining cylinder head type A and B.



g.
A164336

Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the standard oil clearance between the exhaust valve guide bush and exhaust valve stem.

Standard oil clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 3.REPLACE SPARK PLUG TUBE

HINT:

When using a new cylinder head, the spark plug tubes must be replaced.


a.
A053854E12
2.583,1.49 2.583,1.385 2.583,1.385 1.906,1.031 false 1.125,1.927 1.625,2.104 0.5,0.177 10 true 15 mm 2.51,1.531 2.698,1.688 0.188,0.156 10 false *1

Apply adhesive to the end of a new spark plug tube.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.


Standard seal diameter:

15 mm (0.591 in.)


Text in Illustration
*1 Adhesive

NOTICE:
·

Install the spark plug tube within 3 minutes after applying adhesive.

·

Be careful not to deform the spark plug tube.

·

Be careful not to expose the seal to coolant for at least 1 hour after installing the spark plug tube.




b.
U115361E01
1.159,2.459 0.779,2.459 0.779,2.459 1.139,3.278 false 1.205,2.382 1.389,2.537 0.185,0.155 10 *1 1.957,2.938 2.142,3.093 0.185,0.155 10 *2

Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

Standard protrusion height:

75.1 to 76.1 mm (2.96 to 3.00 in.)


Text in Illustration
*1 Cylinder Head Top Surface
*2 Protrusion Height

NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping in the tube.



Hide 11115A 4.REPLACE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.


a.

Remove the ring pins.


b.

Using a plastic-faced hammer, tap in new ring pins to the cylinder head.

U115392E03
1.854,1.677 2.042,1.833 0.188,0.156 10 false *1 2.271,2.167 2.458,2.323 0.188,0.156 10 false *2 2.281,2.802 2.469,2.958 0.188,0.156 10 false *3 0.531,0.073 0.719,0.229 0.188,0.156 10 false *A 3.688,0.073 3.875,0.229 0.188,0.156 10 false *B 0.833,1.219 0.958,1.365 0.125,0.146 10 false A 0.844,0.531 0.969,0.677 0.125,0.146 10 false B 3.927,1.448 4.052,1.594 0.125,0.146 10 false B 3.969,1.094 4.094,1.24 0.125,0.146 10 false A 6.229,1.104 6.354,1.25 0.125,0.146 10 false A 3.073,1.229 3.198,1.375 0.125,0.146 10 false A 5.125,3.354 5.25,3.5 0.125,0.146 10 false B 1.885,3.344 2.01,3.49 0.125,0.146 10 false A 5.104,1.667 5.292,1.823 0.188,0.156 10 false *1 5.521,2.156 5.708,2.313 0.188,0.156 10 false *2 5.552,2.771 5.74,2.927 0.188,0.156 10 false *3

Text in Illustration
*A for Bank 1 *B for Bank 2
*1 Width *2 Height
*3 Protrusion Height - -

Standard Ring Pin:
Item Height Width Protrusion
Ring pin A 11 mm (0.433 in.) 11 mm (0.433 in.) 5.5 to 6.5 mm (0.217 to 0.256 in.)
Ring pin B 10 mm (0.394 in.) 11 mm (0.433 in.) 3.5 to 6.5 mm (0.138 to 0.256 in.)