Home › Engine / Hybrid System › 1UR-FE (ENGINE MECHANICAL) › CYLINDER BLOCK › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052776 1UR-FE ENGINE MECHANICAL _0255042 CYLINDER BLOCK A

1UR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using an E8 "TORX" socket wrench, install the stud bolts.

Torque:
for stud bolt A : 20 N*m (199 kgf*cm, 14 ft.*lbf)
for stud bolt B : 9.0 N*m (92 kgf*cm, 80 in.*lbf)

U162838E02
1.865,5.781 2.865,5.781 false 5.635,5.854 4.531,5.854 false 1.177,2.292 1.177,3.281 false 2.625,2.313 2.625,3.271 false 6.354,2.573 6.354,3.26 false 4.677,1.385 3.771,1.385 false 1.906,4.667 2.594,5 0.688,0.333 10 false 26.5 mm (1.04 in.) 2.896,5.708 3.594,6.052 0.698,0.344 10 false 18 mm (0.709 in.) 2.781,5.198 3.917,5.375 1.135,0.177 10 false 50 mm (1.97 in.) 5.458,5.063 6.156,5.406 0.698,0.344 10 false 29 mm (1.14 in.) 5.667,5.781 6.354,6.125 0.688,0.344 10 false 13 mm (0.512 in.) 4.615,4.969 5.302,5.313 0.688,0.344 10 false 14 mm (0.551 in.) 1.354,6.229 1.479,6.375 0.125,0.146 10 false A 4.052,6.229 4.177,6.375 0.125,0.146 10 false B 0.667,0.385 0.875,0.542 0.208,0.156 10 false *a 4.01,0.385 4.198,0.542 0.188,0.156 10 false *b 3.625,1.344 3.75,1.49 0.125,0.146 10 false A 1.135,3.333 1.26,3.479 0.125,0.146 10 false B 2.583,3.333 2.708,3.479 0.125,0.146 10 false B 6.302,3.313 6.427,3.458 0.125,0.146 10 false A

Text in Illustration
*a Upper Side *b Lower Side


Hide 15708 2.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Using a 5 mm hexagon wrench, install the 4 No. 1 oil nozzles with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13101 3.INSTALL PISTON WITH PIN SUB-ASSEMBLY

a.
A228439E03
2.708,1.5 2.927,1.5 true 2.958,1.427 3.146,1.583 0.188,0.156 10 false *1

Using a screwdriver, install a new snap ring on one side of the piston pin hole.

Text in Illustration
*1 Service Cutout

HINT:

Be sure that the end gap of the snap ring is not aligned with the service cutout of the piston.



b.

Gradually heat the piston to approximately 80°C (176°F).


c.

Coat the piston pin and connecting rod with engine oil.


d.
A218911E01
2.823,2.596 3.008,2.751 0.185,0.155 10 *1 0.776,0.985 0.960,1.140 0.185,0.155 10 *A 2.408,3.198 2.593,3.353 0.185,0.155 10 *B 2.918,2.127 2.918,2.578 false 0.63,3.891 0.815,4.046 0.185,0.155 10 *1 0.724,2.984 0.724,3.873 false

Align the front marks of the piston and connecting rod, insert the connecting rod into the piston, and then push in the piston pin with your thumb until the pin comes into contact with the snap ring.

Text in Illustration
*A for Bank 1
*B for Bank 2
*1 Front Mark

NOTICE:

For the LH side, perform the assembly so that the front marks of the piston and connecting rod are on the same side. For the RH side, perform the assembly so that the front marks of the piston and connecting rod are on opposite sides.


HINT:

The piston and pin are a matched set.



e.

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.


f.
A228439E03
2.708,1.5 2.927,1.5 true 2.958,1.427 3.146,1.583 0.188,0.156 10 false *1

Using a small screwdriver, install a new snap ring at the other end of the piston pin hole.

Text in Illustration
*1 Service Cutout

HINT:

Be sure that the end gap of the snap ring is not aligned with the cutout of the piston.



Hide 13011 4.INSTALL PISTON RING SET

a.
A164414E02
1.458,0.365 1.563,0.365 1.563,0.365 1.771,0.906 false 1.781,1.375 1.781,1.885 false 1.99,1.146 2.5,1.146 false 1.25,0.281 1.438,0.438 0.188,0.156 10 false *1 2.531,1.063 2.719,1.219 0.188,0.156 10 false *2 1.719,1.906 1.906,2.063 0.188,0.156 10 false *3

Install the oil ring (expander) and 2 side rails by hand.

Text in Illustration
*1 Upper Side Rail
*2 Oil Ring Expander
*3 Lower Side Rail


b.

Using a piston ring expander, install the 2 compression rings so that the paint marks are positioned as shown in the illustration.

A332528E05
1.896,0.365 2.24,0.135 2.24,0.135 2.354,0.135 false 1.417,3.052 1.083,1.75 1.083,1.75 0.917,1.75 false 2.052,2.031 1.083,1.75 false 6.031,1.292 6.135,1.427 6.135,1.427 6.135,1.5 false 6.031,2.625 6.135,2.76 6.135,2.76 6.135,2.844 false 4.25,1.938 4.104,2.156 4.104,2.156 4.104,2.26 false 2.563,2.49 3,2.917 3,2.917 3.125,2.917 false 2.01,3.135 2.448,3.469 2.448,3.469 2.573,3.469 false 2.406,0.063 3.823,0.24 1.417,0.177 10 false *c 4.042,2.302 4.26,2.51 0.219,0.208 10 false *1 6.063,1.51 6.302,1.698 0.24,0.188 10 false *2 2.635,1.917 3.167,2.115 0.531,0.198 10 false *e 0.719,1.656 1.125,1.833 0.406,0.177 10 false *d 5.188,0.531 5.76,0.729 0.573,0.198 10 false *a 3.156,2.833 4.729,3.021 1.573,0.188 10 false *1 2.615,3.396 4.188,3.583 1.573,0.188 10 false *2 5.26,1.948 5.833,2.146 0.573,0.198 10 false *b 6.052,2.865 6.292,3.052 0.24,0.188 10 false *2

Text in Illustration
*1 No. 1 Compression Ring *2 No. 2 Compression Ring
*a Type A *b Type B
*c Piston Ring Expander *d Paint Mark
*e Upward - -

HINT:

Type A and type B can be distinguished by the color of the paint marks or the cross-section shape of the No. 2 compression ring.

Item Paint Mark
Type A No. 1 compression ring Blue
No. 2 compression ring Orange
Type B No. 1 compression ring Yellow
No. 2 compression ring Green



c.
A174175E02
1.929,3.034 2.114,3.189 0.185,0.155 10 *1 1.453,0.522 1.638,0.677 0.185,0.155 10 *2 2.411,2.343 2.596,2.498 0.185,0.155 10 *3 2.663,1.31 2.848,1.465 0.185,0.155 10 *4 0.789,2.368 0.973,2.523 0.185,0.155 10 *5 1.83,2.304 2.025,2.9 2.025,2.9 2.025,3.009 false

Position the piston rings so that the ring ends are as shown in the illustration.

Text in Illustration
*1 Front Mark
*2 Upper Side Rail
*3 Lower Side Rail
*4 No. 1 Compression Ring
*5 No. 2 Compression Ring


Hide 11711 5.INSTALL CRANKSHAFT BEARING

NOTICE:

Main bearings come in widths of 21 mm (0.827 in.) and 22.5 mm (0.886 in.). Install the 22.5 mm (0.886 in.) bearings in the No. 1 and No. 5 cylinder block journal positions with the main bearing caps. Install the 21 mm (0.827 in.) bearings in the No. 2, No. 3 and No. 4 positions.


A124282E33
0.625,2.646 1.219,2.792 0.594,0.146 10 false 22.5 mm 2.469,2.583 2.969,2.729 0.5,0.146 10 false 21 mm 0.667,0.708 0.854,0.865 0.188,0.156 10 false *1 2.542,0.677 2.729,0.833 0.188,0.156 10 false *2

Text in Illustration
*1 No. 1 and No. 5 Journal Bearings
*2 No. 2, No. 3 and No. 4 Journal Bearings

a.

Clean each main journal and bearing.


b.

Install the upper bearing.

i.
A142825E02
1.425,2.792 1.610,2.947 0.185,0.155 10 *1 1.638,4.087 1.823,4.242 0.185,0.155 10 *a 2.64,4.087 2.825,4.242 0.185,0.155 10 *b 1.15,3.937 1.335,4.092 0.185,0.155 10 *2 1.365,4.026 1.47,4.026 1.47,4.026 1.612,3.772 false 2.129,3.937 2.314,4.092 0.185,0.155 10 *2 2.344,4.026 2.45,4.026 2.45,4.026 2.592,3.772 false 2.365,2.887 1.635,2.887 false 1.975,3.234 1.728,3.234 1.728,3.234 1.728,2.885 false

Install the upper bearing to the cylinder block.

Text in Illustration
*1 Oil Groove
*2 Oil Feed Hole
*a CORRECT
*b INCORRECT

NOTICE:
·

Do not apply engine oil to the bearings or contact surfaces.

·

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.

·

Do not allow coolant to come into contact with the inner surface of the bearing.

·

If any coolant comes into contact with the inner surface of the bearing, replace the bearing with a new one.





c.

Install the lower bearings.

i.
U115333E03
2.646,2.75 2.542,2.75 2.542,2.75 2.271,3.229 false 0.688,3.573 0.813,3.719 0.125,0.146 10 false A 2.208,3.573 2.333,3.719 0.125,0.146 10 false B 2.677,2.656 2.865,2.813 0.188,0.156 10 false *1

Install the lower bearings to the crankshaft bearing caps.

Text in Illustration
*1 Vernier Caliper


ii.

Using a vernier caliper, measure the distance between the edge of the crankshaft bearing cap and the edge of the lower bearing.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:
·

Do not apply engine oil to the bearings or contact surfaces.

·

Do not allow coolant to come into contact with the inner surface of the bearing.

·

If any coolant comes into contact with the inner surface of the bearing, replace the bearing with a new one.





Hide 11011 6.INSTALL CRANKSHAFT THRUST WASHER SET

a.
A150072E03
1.333,2.063 1.438,2.063 1.438,2.063 1.542,1.823 false 2.323,2.073 2.219,2.073 2.219,2.073 2.125,1.896 false 1.104,0.229 1.208,0.229 1.208,0.229 1.49,0.927 false 2.448,0.281 2.344,0.281 2.344,0.281 2.063,0.99 false 1.125,1.979 1.313,2.135 0.188,0.156 10 false *1 2.344,1.979 2.531,2.135 0.188,0.156 10 false *1 0.896,0.135 1.083,0.292 0.188,0.156 10 false *1 2.479,0.198 2.75,0.448 0.271,0.25 10 true *1

Apply engine oil to the thrust washer set.

Text in Illustration
*1 Oil Groove


b.

Install the 4 thrust washers to the No. 3 journal position of the cylinder block and bearing cap with the oil grooves facing outward.


Hide 13411 7.INSTALL CRANKSHAFT

a.
U115346E01
1.812,2.702 1.812,3.037 false 2.312,2.892 2.312,2.705 false 1.344,2.889 1.344,2.702 false 1.72,3.06 1.905,3.215 0.185,0.155 10 *1

Apply new engine oil to the upper bearing and lower bearing, then place the crankshaft on the cylinder block.

Text in Illustration
*1 Number Mark


b.

Confirm the front marks and numbers of the main bearing caps and install the bearing caps to the cylinder block.

HINT:

A number is marked on each main bearing cap to indicate the installation position.



c.

Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.


d.

Temporarily install the 10 main bearing cap bolts to the inside positions.


e.
A160709E02
1.704,2.988 2.195,3.139 0.491,0.152 10 91 mm 2.292,3.089 2.39,3.089 2.39,3.089 2.492,2.869 false 0.924,2.111 1.109,2.265 0.185,0.155 10 *a

Insert the main bearing cap by hand until the clearance between the main bearing cap and cylinder block is less than 6 mm (0.236 in.) and partially tighten the 2 inner bearing cap bolts.

Bolt length:

91 mm (3.58 in.)


Text in Illustration
*a Less than 6 mm


f.
U115329

Using a plastic-faced hammer, lightly tap the crankshaft bearing cap to ensure a proper fit.


g.

Apply a light coat of engine oil to the threads and under the heads of the 10 main bearing cap bolts.


h.
A228398E01
1.652,3.002 2.250,3.155 0.599,0.153 10 79.5 mm

Temporarily install the 10 main bearing cap bolts to the outside positions.

Bolt length:

79.5 mm (3.13 in.)



i.

Tighten the main bearing cap bolts.

HINT:

The main bearing cap bolts are tightened in 2 progressive steps.


i.
U115345E03
1.313,0.802 1.438,0.958 0.125,0.156 10 false 1 3.156,1.156 3.385,1.323 0.229,0.167 10 false 10 1.979,0.99 2.125,1.146 0.146,0.156 10 false 2 0.792,0.802 0.958,1 0.167,0.198 10 false 3 0.677,1.167 0.792,1.302 0.115,0.135 10 false 4 2.521,0.646 2.656,0.844 0.135,0.198 10 false 5 2.573,1.156 2.729,1.344 0.156,0.188 10 false 6 0.115,0.646 0.229,0.781 0.115,0.135 10 false 7 0.177,0.99 0.313,1.135 0.135,0.146 10 false 8 3.156,0.625 3.313,0.823 0.156,0.198 10 false 9 1.354,0.188 1.552,0.333 0.198,0.146 10 false 11 1.813,1.635 2.042,1.823 0.229,0.188 10 false 12 0.792,0.198 0.99,0.365 0.198,0.167 10 false 13 0.813,1.625 1.01,1.771 0.198,0.146 10 false 14 2.302,0.177 2.5,0.323 0.198,0.146 10 false 15 2.396,1.615 2.615,1.771 0.219,0.156 10 false 16 0.229,0.208 0.427,0.354 0.198,0.146 10 false 17 0.115,1.563 0.313,1.708 0.198,0.146 10 false 18 2.938,0.208 3.156,0.406 0.219,0.198 10 false 19 3.063,1.573 3.292,1.75 0.229,0.177 10 false 20

Step 1:

Uniformly tighten the 20 main bearing cap bolts in the sequence shown in the illustration.

Torque:
for inner bolts : 61 N*m (622 kgf*cm, 45 ft.*lbf)
for outer bolts : 27 N*m (275 kgf*cm, 20 ft.*lbf)

If any of the main bearing cap bolts does not meet the specified torque, replace it.


ii.

Mark the front of the bearing cap bolts with paint.


iii.

Step 2:

Tighten the bearing cap bolts 90° in the order shown in step 1.


iv.

Check that the painted marks are now at a 90° angle to the front.



j.

Check that the crankshaft turns smoothly.


k.
U115347E03
0.885,0.208 1.01,0.354 0.125,0.146 10 false 1 1.188,0.094 1.313,0.24 0.125,0.146 10 false 2 0.531,0.406 0.656,0.552 0.125,0.146 10 false 3 1.927,0.073 2.052,0.219 0.125,0.146 10 false 4 0.146,0.615 0.271,0.76 0.125,0.146 10 false 5 2.563,1.531 2.688,1.677 0.125,0.146 10 false 6 2.313,1.771 2.427,1.906 0.115,0.135 10 false 7 2.969,1.021 3.167,1.167 0.198,0.146 10 false 10 2.771,1.313 2.896,1.458 0.125,0.146 10 false 8 1.177,1.781 1.302,1.927 0.125,0.146 10 false 9

Install and uniformly tighten the 10 main bearing cap bolts and 10 new seal washers in several steps in the sequence shown in the illustration.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


l.

Check that the crankshaft turns smoothly.


Hide 13041 8.INSTALL CONNECTING ROD BEARING

a.
U115445E01
0.233,3.052 0.418,3.207 0.185,0.155 10 *1 1.742,3.075 1.927,3.229 0.185,0.155 10 *2 2.433,4.147 2.618,4.301 0.185,0.155 10 *3 0.436,3.139 0.543,3.139 0.543,3.139 0.675,3.599 false 1.95,3.166 2.365,3.166 false 2.539,4.127 2.539,3.858 false 1.903,3.488 2.024,3.634 0.121,0.145 10 A 3.065,3.488 3.187,3.634 0.121,0.145 10 B

Install the bearing to the connecting rod cap.

Text in Illustration
*1 Vernier Caliper
*2 Connecting Rod Cap
*3 Connecting Rod Bearing

NOTICE:
·

Clean the contact surfaces of the bearing and connecting rod cap.

·

Do not apply engine oil to the bearing or the surface it contacts.




b.

Using a vernier caliper, measure the distance between the connecting rod cap edge and connecting rod bearing edge.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)



c.
U115446E01
0.233,3.052 0.418,3.207 0.185,0.155 10 *1 1.742,3.075 1.927,3.229 0.185,0.155 10 *2 2.433,4.147 2.618,4.301 0.185,0.155 10 *3 0.436,3.139 0.543,3.139 0.543,3.139 0.675,3.599 false 1.95,3.166 2.365,3.166 false 2.539,4.127 2.539,3.858 false 1.903,3.488 2.024,3.634 0.121,0.145 10 A 3.065,3.488 3.187,3.634 0.121,0.145 10 B

Install the bearing to the connecting rod.

Text in Illustration
*1 Vernier Caliper
*2 Connecting Rod
*3 Connecting Rod Bearing

NOTICE:
·

Clean the contact surface of the bearing and connecting rod.

·

Do not apply engine oil to the bearing or the surface it contacts.




d.

Using a vernier caliper, measure the distance between the connecting rod edge and connecting rod bearing edge.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)



Hide 10.INSTALL PISTON AND CONNECTING ROD

a.

Apply engine oil to the cylinder walls, pistons and surfaces of the connecting rod bearings.


b.
A174175E02
1.929,3.034 2.114,3.189 0.185,0.155 10 *1 1.453,0.522 1.638,0.677 0.185,0.155 10 *2 2.411,2.343 2.596,2.498 0.185,0.155 10 *3 2.663,1.31 2.848,1.465 0.185,0.155 10 *4 0.789,2.368 0.973,2.523 0.185,0.155 10 *5 1.83,2.304 2.025,2.9 2.025,2.9 2.025,3.009 false

Check the positions of the piston ring ends.

Text in Illustration
*1 Front Mark
*2 Upper Side Rail
*3 Lower Side Rail
*4 No. 1 Compression Ring
*5 No. 2 Compression Ring

NOTICE:

Do not align the ring ends.


HINT:

The expander ends can be placed anywhere.



c.
A214552E02
0.455,2.54 0.640,2.695 0.185,0.155 10 *1 0.11,1.79 0.295,1.944 0.185,0.155 10 *A 0.11,3.305 0.295,3.460 0.185,0.155 10 *B 1.277,2.626 0.66,2.626 false 0.455,4.051 0.640,4.205 0.185,0.155 10 *1 1.292,4.137 0.66,4.137 false 2.749,3.999 2.933,4.154 0.185,0.155 10 *1 2.84,3.348 2.84,3.98 false

Using a hammer handle and piston ring compressor, press a piston and connecting rod assembly into each cylinder with the front mark of the piston facing forward.

Text in Illustration
*A for Bank 1
*B for Bank 2
*1 Front Mark


d.

Place the connecting rod cap on the connecting rod.

i.
A218936E03
1.906,1.104 1.479,1.406 1.479,1.406 1.354,1.406 true 1.635,3.729 1.208,4.031 1.208,4.031 1.083,4.031 true 1.146,1.323 1.354,1.552 0.208,0.229 10 true *1 0.052,0.052 0.24,0.208 0.188,0.156 10 false *A 0.052,2.5 0.24,2.656 0.188,0.156 10 false *B 0.885,3.948 1.063,4.229 0.177,0.281 10 true *1

Match the numbered connecting rod cap with the connecting rod.

Text in Illustration
*A for Bank 1
*B for Bank 2
*1 Front Mark
V100135

Front


ii.

Check that the front mark of the connecting rod cap is facing the proper direction.

Front Mark:
Item Front Mark
LH Front Side
RH Rear Side




e.

Install the connecting rod cap bolts.

HINT:

The connecting rod cap bolts are tightened in 2 progressive steps.


i.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


ii.

Temporarily install the connecting rod cap bolts.


iii.
A214339

Step 1:

Install and alternately tighten the bolts of each connecting rod cap in several steps.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


iv.

Mark the front side of each connecting rod cap bolt with paint.


v.

Step 2:

Tighten the cap bolts 90°.


vi.

Check that the paint marks are now at a 90° angle to the front.



f.

Check that the crankshaft turns smoothly.