86011A
1.INSTALL NOISE FILTER
Install the 2 noise filters to the cylinder head cover with the 2 bolts.
19500
2.INSTALL IGNITION COIL ASSEMBLY
Install the 8 ignition coils with the 8 bolts.
12315
3.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH
Install the mounting bracket with the 4 bolts.
12311
4.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH
Install the mounting bracket with the 4 bolts.
11415
5.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
Apply adhesive to 2 or 3 threads of the drain cocks.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install the water drain cocks as shown in the illustration.
| *A | LH |
| *B | RH |
| *a | Front |
Do not rotate the drain cocks more than 1 revolution (360°) after tightening the drain cocks to the specified torque.
Do not loosen the drain cocks to adjust them. If an adjustment is necessary, remove the drain cocks and reinstall them.
Install the water drain cock plugs to the water drain cocks.
89615
6.INSTALL KNOCK SENSOR
Install the 4 sensors with the 4 bolts so that the sensors are angled as shown in the illustration.
| *1 | Bank 2 Sensor 1 |
| *2 | Bank 1 Sensor 1 |
| *3 | Bank 2 Sensor 2 |
| *4 | Bank 1 Sensor 2 |
| *a | Front |
| *b | Rear |
| *c | Top |
The acceptable installation angle of the sensor is between 10° upward and downward from the horizontal position.
12215
7.INSTALL SEPARATOR CASE
After inserting the pipe on the rear of the separator case into the oil return pipe and the pipe on the front into the ventilation pipe, temporarily install bolt A.
Temporarily install bolt B and tighten bolt A.
Install the bolts labeled C.
Tighten bolt B.
| Item | Length | Thread Diameter |
|---|---|---|
| Bolt A | 25 mm (0.984 in.) | 6 mm (0.236 in.) |
| Bolt B and C | 16 mm (0.630 in.) | 6 mm (0.236 in.) |
82219A
8.INSTALL SENSOR WIRE
Connect the 3 clamps and 4 knock sensor connectors.
16206
9.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
Install the water by-pass pipe with the 2 bolts.
16323
10.INSTALL WATER INLET HOUSING
16355
11.INSTALL FRONT WATER BY-PASS JOINT
16261G
12.INSTALL NO. 1 WATER BY-PASS HOSE
16207
13.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
12611
14.INSTALL NO. 1 ENGINE COVER
11212
15.INSTALL NO. 2 ENGINE COVER
23901
16.INSTALL NO. 1 FUEL TUBE
23902
17.INSTALL NO. 2 FUEL TUBE
Install the No. 2 fuel tube with the 2 bolts.
17111
18.INSTALL INTAKE MANIFOLD
Place 2 new gaskets on the intake manifold.
Place the intake manifold on the cylinder head.
Install and uniformly tighten the 8 bolts and 2 nuts in several steps.
Install the wire bracket to the intake manifold with the bolt.
Connect the No. 1 ventilation hose.
Connect the 2 water by-pass hoses.
Connect the ventilation hose to the ventilation pipe of the cylinder head cover LH and RH.
23250
19.INSTALL FUEL INJECTOR ASSEMBLY
23807
20.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY RH
23808
21.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY LH
23901
22.CONNECT NO. 1 FUEL TUBE
23902
23.CONNECT NO. 2 FUEL TUBE
23271H
24.INSTALL NO. 1 FUEL HOSE
Install the fuel hose (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).
12613
25.INSTALL NO. 3 ENGINE COVER
12601B
26.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
27.INSTALL ENGINE WIRE
Install the engine wire.
Engine Rear Side:
Install the 3 bolts as shown in the illustration.
Connect the 5 clamps.
Connect the sensor wire connector.
Engine RH Side:
Connect the 9 clamps.
Connect the oil pressure sender gauge connector.
Connect the throttle sensor connector.
Connect the noise filter connector.
Connect the fuel injector connector.
Connect the 2 VVT sensor connectors.
The wire harnesses on the exhaust side are wrapped with white tape.
Connect the 4 ignition coil connectors.
Connect the 2 camshaft timing control valve connectors.
The wire harnesses on the exhaust side are wrapped with white tape.
Engine LH Side:
Connect the 7 clamps and install the engine wire with the bolt.
Connect the noise filter connector.
Connect the fuel injector connector.
Connect the engine coolant temperature sensor connector.
Connect the purge VSV connector.
Connect the vacuum switching valve connector (for ACIS).
Connect the camshaft position sensor connector.
Connect the 2 VVT sensor connectors.
The wire harnesses on the exhaust side are wrapped with white tape.
Connect the 4 ignition coil connectors.
Connect the 2 camshaft timing control valve connectors.
The wire harnesses on the exhaust side are wrapped with white tape.