11101
1.INSPECT CYLINDER HEAD SUB-ASSEMBLY
Using a precision straightedge and feeler gauge, measure the warpage of the surfaces where the cylinder head contacts the cylinder block and manifold.
| Item | Specified Condition |
|---|---|
| Cylinder head lower side | 0.05 mm (0.00197 in.) |
| Intake side | 0.08 mm (0.00315 in.) |
| Exhaust side | 0.05 mm (0.00197 in.) |
0.10 mm (0.00394 in.)
| *A | Cylinder Head Lower Side |
| *B | Intake Side |
| *C | Exhaust Side |
If the warpage is more than the maximum, replace the cylinder head.
Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
If cracked, replace the cylinder head.
13711
2.INSPECT INTAKE VALVE
Using a micrometer, measure the diameter of the valve stem.
5.470 to 5.485 mm (0.215 to 0.216 in.)
If the diameter is not as specified, replace the valve and guide bush.
Using a vernier caliper, measure the valve head margin thickness.
1.25 mm (0.0492 in.)
0.50 mm (0.0197 in.)
| *1 | Margin Thickness |
If the margin thickness is less than the minimum, replace the intake valve.
Using a vernier caliper, measure the valve overall length.
105.85 mm (4.17 in.)
105.35 mm (4.15 in.)
If the overall length is less than the minimum, replace the intake valve.
13715
3.INSPECT EXHAUST VALVE
Using a micrometer, measure the diameter of the valve stem.
5.465 to 5.480 mm (0.215 to 0.216 in.)
If the diameter is not as specified, replace the valve and guide bush.
Using a vernier caliper, measure the valve head margin thickness.
1.4 mm (0.0551 in.)
0.50 mm (0.0197 in.)
| *1 | Margin Thickness |
If the margin thickness is less than the minimum, replace the exhaust valve.
Using a vernier caliper, measure the valve overall length.
110.40 mm (4.35 in.)
109.90 mm (4.33 in.)
If the overall length is less than the minimum, replace the exhaust valve.
11131
4.INSPECT INTAKE VALVE SEAT
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
Do not rotate the valve while pressing the valve.
Check the valve face and valve seat.
| *1 | Width |
Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).
If not, correct the valve seat.
Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.
If not, correct the valve seat.
11135
5.INSPECT EXHAUST VALVE SEAT
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
Do not rotate the valve while pressing the valve.
Check the valve face and valve seat.
| *1 | Width |
Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).
If not, correct the valve seat.
Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.
If not, correct the valve seat.
13711B
6.INSPECT COMPRESSION SPRING
The shape of the inner compression spring determines whether the valve spring type described here is A or B.
Using a vernier caliper, measure the free length of the inner compression spring.
| Type | Specified Condition |
|---|---|
| Valve Spring Type A | 49.69 to 53.19 mm (1.96 to 2.09 in.) |
| Valve Spring Type B | 49.38 to 53.38 mm (1.94 to 2.10 in.) |
If the free length is not as specified, replace the spring.
Valve Spring Type A:
Using a steel square, measure the deviation of the inner compression spring.
1.0 mm (0.0394 in.)
2°
| *1 | Deviation |
If the deviation is greater than the maximum, replace the spring.
Valve Spring Type B:
Using a steel square, measure the deviation of the inner compression spring.
1.0 mm (0.0394 in.)
2°
| *1 | Deviation |
If the deviation is greater than the maximum, replace the spring.
7.INSPECT VALVE GUIDE BUSH OIL CLEARANCE
Using a caliper gauge, measure the inside diameter of the guide bush.
5.51 to 5.53 mm (0.217 to 0.218 in.)
Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.
| Item | Specified Condition |
|---|---|
| Intake | 0.025 to 0.060 mm (0.000984 to 0.00236 in.) |
| Exhaust | 0.030 to 0.065 mm (0.00118 to 0.00256 in.) |
| Item | Specified Condition |
|---|---|
| Intake | 0.08 mm (0.00315 in.) |
| Exhaust | 0.10 mm (0.00394 in.) |
If the oil clearance is more than the maximum, replace the valve and guide bush.
8.INSPECT CAMSHAFT THRUST CLEARANCE
Inspect the bank 1 camshafts.
Install the bank 1 camshafts.
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
0.08 to 0.135 mm (0.00315 to 0.00531 in.)
0.15 mm (0.00591 in.)
If the thrust clearance is more than the maximum, replace the camshaft housing. If the thrust surface is damaged, replace the camshaft.
Inspect the bank 2 camshafts.
Install the bank 2 camshafts.
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
0.08 to 0.135 mm (0.00315 to 0.00531 in.)
0.15 mm (0.00591 in.)
If the thrust clearance is more than the maximum, replace the camshaft housing. If the thrust surface is damaged, replace the camshaft.