Home › Engine / Hybrid System › 3UR-FE (ENGINE MECHANICAL) › CYLINDER HEAD › 2015.08–2016.08
RM2660E _51 Engine / Hybrid System _052777 3UR-FE ENGINE MECHANICAL _0255051 CYLINDER HEAD G

3UR-FE ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 11101 1.INSPECT CYLINDER HEAD SUB-ASSEMBLY

A385328E01
4.115,0.125 4.427,0.323 0.313,0.198 10 false *A 4.104,1.698 4.417,1.896 0.313,0.198 10 false *B 4.104,2.771 4.417,2.969 0.313,0.198 10 false *C

a.

Using a precision straightedge and feeler gauge, measure the warpage of the surfaces where the cylinder head contacts the cylinder block and manifold.

Standard Warpage:
Item Specified Condition
Cylinder head lower side 0.05 mm (0.00197 in.)
Intake side 0.08 mm (0.00315 in.)
Exhaust side 0.05 mm (0.00197 in.)


Maximum warpage:

0.10 mm (0.00394 in.)


Text in Illustration
*A Cylinder Head Lower Side
*B Intake Side
*C Exhaust Side

If the warpage is more than the maximum, replace the cylinder head.


b.

Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.

If cracked, replace the cylinder head.


Hide 13711 2.INSPECT INTAKE VALVE

a.

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

5.470 to 5.485 mm (0.215 to 0.216 in.)


If the diameter is not as specified, replace the valve and guide bush.


b.
A131998E03
0.442,1.665 0.610,1.859 0.169,0.194 10 *1

Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.25 mm (0.0492 in.)


Minimum margin thickness:

0.50 mm (0.0197 in.)


Text in Illustration
*1 Margin Thickness

If the margin thickness is less than the minimum, replace the intake valve.


c.

Using a vernier caliper, measure the valve overall length.

Standard overall length:

105.85 mm (4.17 in.)


Minimum overall length:

105.35 mm (4.15 in.)


If the overall length is less than the minimum, replace the intake valve.


Hide 13715 3.INSPECT EXHAUST VALVE

a.

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

5.465 to 5.480 mm (0.215 to 0.216 in.)


If the diameter is not as specified, replace the valve and guide bush.


b.
A132001E03
0.407,1.785 0.597,1.960 0.189,0.175 10 *1

Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.4 mm (0.0551 in.)


Minimum margin thickness:

0.50 mm (0.0197 in.)


Text in Illustration
*1 Margin Thickness

If the margin thickness is less than the minimum, replace the exhaust valve.


c.

Using a vernier caliper, measure the valve overall length.

Standard overall length:

110.40 mm (4.35 in.)


Minimum overall length:

109.90 mm (4.33 in.)


If the overall length is less than the minimum, replace the exhaust valve.


Hide 11131 4.INSPECT INTAKE VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.

HINT:

Do not rotate the valve while pressing the valve.



c.
A149128E05
1.443,1.074 1.624,1.251 0.181,0.177 10 *1

Check the valve face and valve seat.

Text in Illustration
*1 Width

i.

Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).

If not, correct the valve seat.


ii.

Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.

If not, correct the valve seat.



Hide 11135 5.INSPECT EXHAUST VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.

HINT:

Do not rotate the valve while pressing the valve.



c.
A149129E04
1.052,1.042 1.24,1.219 0.188,0.177 10 false *1

Check the valve face and valve seat.

Text in Illustration
*1 Width

i.

Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).

If not, correct the valve seat.


ii.

Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.

If not, correct the valve seat.



Hide 13711B 6.INSPECT COMPRESSION SPRING

HINT:

The shape of the inner compression spring determines whether the valve spring type described here is A or B.


a.
A101392

Using a vernier caliper, measure the free length of the inner compression spring.

Standard free length:
Type Specified Condition
Valve Spring Type A 49.69 to 53.19 mm (1.96 to 2.09 in.)
Valve Spring Type B 49.38 to 53.38 mm (1.94 to 2.10 in.)


If the free length is not as specified, replace the spring.


b.
A101393E04
1.213,0.106 1.398,0.260 0.185,0.155 10 *1

Valve Spring Type A:

i.

Using a steel square, measure the deviation of the inner compression spring.

Maximum deviation:

1.0 mm (0.0394 in.)


Maximum angle (reference):

2°


Text in Illustration
*1 Deviation

If the deviation is greater than the maximum, replace the spring.



c.
A319225E24
0.042,1.208 1.146,1.438 1.104,0.229 10 false 40 mm (1.57 in.) 2.323,0.396 2.563,0.615 0.24,0.219 10 false *1

Valve Spring Type B:

i.

Using a steel square, measure the deviation of the inner compression spring.

Maximum deviation:

1.0 mm (0.0394 in.)


Maximum angle (reference):

2°


Text in Illustration
*1 Deviation

If the deviation is greater than the maximum, replace the spring.



Hide 7.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

A145559

a.

Using a caliper gauge, measure the inside diameter of the guide bush.

Standard bush inside diameter:

5.51 to 5.53 mm (0.217 to 0.218 in.)



b.

Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.08 mm (0.00315 in.)
Exhaust 0.10 mm (0.00394 in.)


If the oil clearance is more than the maximum, replace the valve and guide bush.


Hide 8.INSPECT CAMSHAFT THRUST CLEARANCE

a.

Inspect the bank 1 camshafts.

i.

Install the bank 1 camshafts.


ii.
A160690

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.08 to 0.135 mm (0.00315 to 0.00531 in.)


Maximum thrust clearance:

0.15 mm (0.00591 in.)


If the thrust clearance is more than the maximum, replace the camshaft housing. If the thrust surface is damaged, replace the camshaft.



b.

Inspect the bank 2 camshafts.

i.

Install the bank 2 camshafts.


ii.

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.08 to 0.135 mm (0.00315 to 0.00531 in.)


Maximum thrust clearance:

0.15 mm (0.00591 in.)


If the thrust clearance is more than the maximum, replace the camshaft housing. If the thrust surface is damaged, replace the camshaft.