Home › Engine / Hybrid System › 3UR-FE (ENGINE MECHANICAL) › CYLINDER HEAD › 2014.08–2016.08
RM2660E _51 Engine / Hybrid System _052777 3UR-FE ENGINE MECHANICAL _0255051 CYLINDER HEAD A

3UR-FE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

There are two cylinder head assembly shapes. Valve spring type A can only be used with cylinder head type A and valve spring type B can only be used with cylinder head type B. The combination cannot be changed.


HINT:
·

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly or cylinder head sub-assembly LH (See page ).

·
A384519N02
2.927,1.292 3.188,1.531 0.26,0.24 10 true (A)

The standard protrusion amount (A) of the valve guide bush determines whether the cylinder head is type A or B.

Standard Protrusion Height (A)
Type Specified Condition
Cylinder Head Type A 14.3 to 14.7 mm (0.563 to 0.579 in.)
Cylinder Head Type B 15.8 to 16.2 mm (0.622 to 0.638 in.)

·
A384520C02
1.781,0.021 3.396,4.427 1.615,4.406 0.021,0.021 1.719,4.427 1.698,4.406 1.229,1.677 1.396,1.677 false 2.958,1.677 3.125,1.677 false 0.927,2.552 1.344,2.552 false 2.625,2.552 3.042,2.552 false 0.958,3.833 1.323,3.833 false 2.646,3.865 3.01,3.865 false 0.052,0.052 0.271,0.26 0.219,0.208 10 false *A 1.813,0.042 2.052,0.24 0.24,0.198 10 false *B 1.448,1.604 1.656,1.781 0.208,0.177 10 false *1 1.375,2.479 1.594,2.677 0.219,0.198 10 false *2 1.354,3.76 1.573,3.969 0.219,0.208 10 false *3 0.656,2.094 0.865,2.292 0.208,0.198 10 false *a 1.396,0.594 1.594,0.792 0.198,0.198 10 false *b 2.354,2.094 2.563,2.292 0.208,0.198 10 false *a 3.115,0.594 3.313,0.792 0.198,0.198 10 false *b 3.052,3.792 3.271,4 0.219,0.208 10 false *3 3.083,2.469 3.302,2.667 0.219,0.198 10 false *2 3.167,1.604 3.375,1.781 0.208,0.177 10 false *1
*A Valve Spring Type A
*B Valve Spring Type B
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Spring Retainer
*3 Inner Compression Spring
*a Valve Spring Retainer Outer Diameter
*b No. 1 Valve Rocker Arm Roller Width


The shape of the inner compression spring determines whether the valve spring type is A or B.

·

The No. 1 valve rocker arm, inner compression spring and valve spring retainer have two different shapes and are not interchangeable.

Valve Spring Type No. 1 Valve Rocker Arm Roller Width Valve Spring Retainer Outer Diameter Inner Compression Spring Shape
A 10.7 mm (0.421 in.) 23.4 mm (0.921 in.) Straight
B 8.0 mm (0.315 in.) 18.9 mm (0.744 in.) Taper



PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If the stud bolt is deformed or its threads are damaged, replace it.


a.

Using E7 and E8 "TORX" socket wrenches, install the stud bolts.

Torque:
for stud bolts A, B, C and D : 9.0 N*m (92 kgf*cm, 80 in.*lbf)

U162971E02
0.885,5.469 1.146,5.115 1.146,5.115 1.229,5.115 false 0.885,6.281 1.24,6.448 1.24,6.448 1.24,6.521 false 2.75,5.302 2.646,5.302 2.646,5.302 2.458,5.688 false 2.479,6.302 2.771,6.458 2.771,6.458 2.771,6.521 false 4.125,6.302 4.406,6.448 4.406,6.448 4.406,6.531 false 5.635,6.302 5.885,6.375 5.885,6.375 5.885,6.479 false 5.615,5.969 5.833,5.635 5.833,5.635 5.938,5.635 false 4.417,5.5 4.333,5.5 4.333,5.5 4.115,5.927 false 2.896,1 2.896,1.438 false 4.323,0.896 4.323,1.396 false 1.042,2.74 1.042,2.948 false 1.313,2.448 1.313,2.958 false 1.594,2.76 1.594,2.979 false 1.875,2.458 1.875,2.969 false 2.167,2.74 2.167,2.969 false 2.427,2.74 2.427,2.969 false 1.76,2.958 1.76,3.146 false 4.646,2.76 4.646,2.969 false 4.906,2.469 4.906,2.969 false 5.198,2.781 5.198,2.969 false 5.458,2.771 5.458,2.969 false 5.781,2.458 5.781,2.969 false 6.021,2.458 6.021,2.969 false 5.365,2.969 5.365,3.156 false 6.104,4.281 6.604,4.281 false 6.198,4.01 6.417,4.01 6.417,4.01 6.417,4.281 false 0.771,3.875 0.948,3.875 0.948,3.875 1.188,3.948 false 1.198,4.281 0.781,4.281 false 0.969,4.229 0.969,3.958 0.969,3.958 1.104,3.958 false 0.448,0.115 1.719,0.417 1.271,0.302 10 false *A 0.448,1.813 1.823,2.031 1.375,0.219 10 false *B 0.448,3.406 2.135,3.656 1.688,0.25 10 false *C 1.25,5.042 2.385,5.229 1.135,0.188 10 false 12 mm (0.472 in.) 1.406,5.708 2.083,6.073 0.677,0.365 10 false 52 mm (2.05 in.) 2.448,6.542 3.604,6.75 1.156,0.208 10 false 13 mm (0.512 in.) 2.792,5.24 4.063,5.396 1.271,0.156 10 false 24 mm (0.945 in.) 2.938,5.792 3.594,6.156 0.656,0.365 10 false 45 mm (1.77 in.) 4.458,5.427 5.594,5.583 1.135,0.156 10 false 20 mm (0.787 in.) 5.969,5.563 7.125,5.719 1.156,0.156 10 false 14 mm (0.551 in.) 4.573,5.875 5.24,6.25 0.667,0.375 10 false 35 mm (1.38 in.) 6.104,5.854 6.792,6.219 0.688,0.365 10 false 29 mm (1.14 in.) 0.583,6.531 0.74,6.698 0.156,0.167 10 false A 0.646,3.76 0.802,3.927 0.156,0.167 10 false A 2.188,6.531 2.323,6.708 0.135,0.177 10 false B 1.708,3.167 1.844,3.344 0.135,0.177 10 false C 3.823,6.531 3.969,6.729 0.146,0.198 10 false C 2.854,1.448 3,1.646 0.146,0.198 10 false B 5.333,6.521 5.469,6.667 0.135,0.146 10 false D 0.646,4.156 0.781,4.302 0.135,0.146 10 false D 6.635,4.219 6.771,4.365 0.135,0.146 10 false D 0.896,6.531 2.031,6.719 1.135,0.188 10 false 12 mm (0.472 in.) 4.094,6.521 5.25,6.729 1.156,0.208 10 false 13 mm (0.512 in.) 5.573,6.458 6.729,6.667 1.156,0.208 10 false 13 mm (0.512 in.) 4.281,1.438 4.427,1.635 0.146,0.198 10 false B 5.313,3.188 5.448,3.365 0.135,0.177 10 false C 4.125,0.115 6,0.365 1.875,0.25 10 false *D 4.052,1.729 5.969,1.99 1.917,0.26 10 false *E 4.146,3.396 5.885,3.646 1.74,0.25 10 false *F

Text in Illustration
*A LH for Intake Side *B LH for Exhaust Side
*C LH for Front Side *D RH for Intake Side
*E RH for Exhaust Side *F RH for Front Side


Hide 11117F 2.INSTALL NO. 2 STRAIGHT SCREW PLUG

A174133E07
0.177,0.135 0.438,0.354 0.26,0.219 10 false *A 0.208,2.365 0.438,2.573 0.229,0.208 10 false *B

NOTICE:

If water leaks from the No. 2 straight screw plug or the plug is corroded, replace it.


a.

Using a 14 mm hexagon wrench, install 2 new gaskets and the 2 straight screw plugs.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

Text in Illustration
*A LH
*B RH


Hide 11117E 3.INSTALL NO. 1 STRAIGHT SCREW PLUG

A174132E06
0.125,0.229 0.469,0.469 0.344,0.24 10 false *A 0.156,2.313 0.469,2.552 0.313,0.24 10 false *B

NOTICE:

If water leaks from the No. 1 straight screw plug or the plug is corroded, replace it.


a.

Using a 10 mm hexagon wrench, install 6 new gaskets and the 6 straight screw plugs.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

Text in Illustration
*A LH
*B RH


Hide 13734 4.INSTALL VALVE SPRING SEAT

a.

Install the valve spring seats to the cylinder head.


Hide 13711A 5.INSTALL VALVE STEM OIL SEAL

a.
A385329E01
1.052,1.375 1.26,1.271 1.26,1.271 1.406,1.271 false 1.917,0.99 2.042,0.99 2.042,0.99 2.302,1.302 false 0.635,0.24 0.948,0.438 0.313,0.198 10 false *A 2.542,0.24 2.854,0.438 0.313,0.198 10 false *B 1.427,1.188 1.74,1.385 0.313,0.198 10 false *1 1.729,0.917 2.042,1.115 0.313,0.198 10 false *2

Apply a light coat of engine oil to new oil seals.

Text in Illustration
*A Intake Side
*B Exhaust Side
*1 Brown
*2 Gray

NOTICE:

Pay attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal into the exhaust side or installing the exhaust oil seal into the intake side can cause installation problems later.


HINT:

The intake valve oil seals are brown and the exhaust valve oil seals are gray.



b.
A165065E06
0.573,1.583 0.823,1.583 0.823,1.583 1.573,1.104 false 0.167,1.5 0.51,1.688 0.344,0.188 10 false SST 0.896,2.323 1.094,2.521 0.198,0.198 10 false *a 2.365,2.313 2.563,2.49 0.198,0.177 10 false *b

Using SST, push in the oil seals.

SST
09201-41020  

Text in Illustration
*a CORRECT
*b INCORRECT

NOTICE:

Failure to use SST will cause the seal to be damaged or improperly seated.



Hide 13711 6.INSTALL INTAKE VALVE

HINT:

The shape of the inner compression spring determines whether the valve spring type described here is A or B.


a.
A385330E01
2.625,1.552 2.938,1.75 0.313,0.198 10 false *a

Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.

Text in Illustration
*a 40 mm (1.57 in.) or more


b.
A366793E03
0.51,0.385 0.781,0.635 0.271,0.25 10 false *a 0.531,1.552 0.781,1.781 0.25,0.229 10 false *b 0.115,0.146 0.427,0.344 0.313,0.198 10 false *A

Install the intake valve, compression spring and valve spring retainer to the cylinder head.

Text in Illustration
*A Valve Spring Type B
*a Narrow
*b Wide

NOTICE:
·

Install the same parts in the same combination to their original locations.

·

Valve Spring Type B:

Install the inner compression spring to the wide end of the cylinder head sub-assembly.




c.
A164326E09
2.708,0.458 2.26,0.458 false 1.521,0.583 1.604,0.083 1.604,0.083 1.708,0.083 false 1.75,0 2.063,0.177 0.313,0.177 10 false SST 1.885,0.375 2.198,0.552 0.313,0.177 10 false SST

Valve Spring Type A:

i.

Using SST and wooden blocks, compress the spring and install the retainer locks.

SST
09202-70020  (09202-00010, 09202-01010, 09202-01020)


ii.
A165066

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Do not damage the valve stem tip.

·

Be careful not to damage the retainer.





d.
A366791E01
2.917,0.323 3.01,0.323 false 0.438,0.656 0.563,0.656 0.563,0.656 0.667,0.844 true 0.094,0.573 0.448,0.771 0.354,0.198 10 false SST 3.063,0.229 3.417,0.427 0.354,0.198 10 true SST

Valve Spring Type B:

i.

Using SST and wooden blocks, compress the spring and install the retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  


ii.
A366795

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Do not damage the valve stem tip.

·

Be careful not to damage the retainer.





Hide 13715 7.INSTALL EXHAUST VALVE

HINT:

The shape of the inner compression spring determines whether the valve spring type described here is A or B.


a.
A385330E01
2.625,1.552 2.938,1.75 0.313,0.198 10 false *a

Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.

Text in Illustration
*a 40 mm (1.57 in.) or more


b.
A366794E03
0.698,0.323 0.948,0.573 0.25,0.25 10 false *a 0.698,1.5 0.948,1.729 0.25,0.229 10 false *b 0.135,0.156 0.406,0.438 0.271,0.281 10 false *A

Install the exhaust valve, compression spring and valve spring retainer to the cylinder head.

Text in Illustration
*A Valve Spring Type B
*a Narrow
*b Wide

NOTICE:
·

Install the same parts in the same combination to their original locations.

·

Valve Spring Type B:

Install the inner compression spring to the wide end of the cylinder head sub-assembly.




c.
A164327E03
1.267,0.047 1.587,0.193 0.319,0.146 10 SST 1.23,0.126 1.137,0.126 1.137,0.126 0.76,0.362 false 2.759,1.799 3.078,1.945 0.319,0.146 10 SST 2.936,1.773 2.936,1.563 false

Valve Spring Type A:

i.

Using SST and wooden blocks, compress the spring and install the retainer locks.

SST
09202-70020  (09202-00010, 09202-01010, 09202-01020)


ii.
A165067

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Do not damage the valve stem tip.

·

Be careful not to damage the retainer.





d.
A366792E01
0.417,0.271 0.542,0.271 false 2.99,1.698 2.885,1.698 2.885,1.698 2.792,1.594 true 0.104,0.188 0.438,0.396 0.333,0.208 10 false SST 3.031,1.615 3.365,1.823 0.333,0.208 10 false SST

Valve Spring Type B:

i.

Using SST and wooden blocks, compress the spring and install the retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  


ii.
A366796

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Do not damage the valve stem tip.

·

Be careful not to damage the retainer.