Home › Engine / Hybrid System › 3UR-FE (ENGINE MECHANICAL) › CYLINDER BLOCK
RM2660E _51 Engine / Hybrid System _052777 3UR-FE ENGINE MECHANICAL _0255052 CYLINDER BLOCK A

3UR-FE ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A174173

Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

Standard thrust clearance:

0.15 to 0.55 mm (0.00591 to 0.0217 in.)


Maximum thrust clearance:

0.70 mm (0.0276 in.)


If the thrust clearance is more than the maximum, replace one or more connecting rods as necessary.

If necessary, replace the crankshaft.


Hide 2.INSPECT CONNECTING ROD OIL CLEARANCE

a.

Check that the front mark on the connecting rod and cap are aligned to ensure correct reassembly.


b.
A161898

Remove the 2 connecting rod cap bolts.


c.
A161899

Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.

HINT:

Keep the lower bearing inserted to the connecting rod cap.



d.

Check the crank pin and bearing for pitting and scratches.

If the crank pin or bearing is damaged, replace the bearings. If necessary, replace the crankshaft.


e.

Clean the crank pin and bearing.


f.
A161900E02
0.677,0.375 0.875,0.375 0.875,0.375 1.604,0.948 false 0.479,0.292 0.656,0.458 0.177,0.167 10 false *1

Lay a strip of Plastigage on the crank pin.

Text in Illustration
*1 Plastigage


g.
A161901E06
1.667,0.771 1.208,1.24 1.208,1.24 0.99,1.24 false 0.781,1.156 0.969,1.354 0.188,0.198 10 true *1

Place the connecting rod cap on the connecting rod with the front mark facing forward.

Text in Illustration
*1 Front Mark
V100135

Front


h.
A161902

Install and alternately tighten the bolts of the connecting rod cap in several steps.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

NOTICE:

Do not turn the crankshaft.



i.

Mark the front side of each connecting rod cap bolt with paint.


j.

Tighten the cap bolts 90° as shown in the illustration.


k.

Check that the painted marks are now at a 90° angle to the front.

NOTICE:

Do not turn the crankshaft.



l.
A161898

Remove the 2 connecting rod cap bolts.


m.
A161899

Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.

HINT:

Keep the lower bearing inserted to the connecting rod cap.



n.

Measure the Plastigage at its widest point.

A385333E02
1.156,1.615 1.365,1.615 1.365,1.615 1.771,2.385 true 4.604,1.958 4.604,1.583 true 5.781,2.74 5.781,2.135 true 5.406,2.708 5.573,2.708 5.573,2.708 5.719,2.094 true 5.177,2.531 5.385,2.531 5.385,2.531 5.667,2.063 true 5.094,2.323 5.24,2.323 5.24,2.323 5.625,2.021 true 5.281,4.479 5.281,4.198 5.281,4.198 4.333,3.906 true 5.563,3.802 5.281,4.198 5.281,4.198 5.479,3.635 true 0.948,1.531 1.26,1.729 0.313,0.198 10 false *1 4.542,2.021 4.854,2.219 0.313,0.198 10 false *2 5.729,2.792 6.042,2.99 0.313,0.198 10 false *3 5.229,2.635 5.542,2.833 0.313,0.198 10 false *4 4.99,2.448 5.302,2.646 0.313,0.198 10 false *5 4.917,2.24 5.229,2.438 0.313,0.198 10 false *6 5.25,4.542 5.563,4.74 0.313,0.198 10 false *2

Standard oil clearance:

0.025 to 0.050 mm (0.000984 to 0.00197 in.)


Maximum oil clearance:

0.070 mm (0.00276 in.)


Text in Illustration
*1 Plastigage
*2 Number Mark
*3 No. 1
*4 No. 2
*5 No. 3
*6 No. 4

If the oil clearance is more than the maximum, replace the bearings. If necessary, replace the crankshaft.

HINT:
·

If replacing a bearing, replace it with one that has the same number as its respective connecting rod cap. The standard thickness of each bearing is indicated by a 1, 2, 3 or 4 mark on its surface.

·

Select the correct bearing by adding together the number marks imprinted on the connecting rod big end and crank pin.


Example:

Connecting rod "1" + Crank pin "2" = 3 (Use bearing "3")


Reference:

Standard Sized Bearing Center Wall Thickness:
Mark Thickness
2 1.489 to 1.492 mm (0.0586 to 0.0587 in.)
3 1.492 to 1.495 mm (0.0587 to 0.0589 in.)
4 1.495 to 1.498 mm (0.0589 to 0.0590 in.)
5 1.498 to 1.501 mm (0.0590 to 0.0591 in.)
6 1.501 to 1.504 mm (0.0591 to 0.0592 in.)
7 1.504 to 1.507 mm (0.0592 to 0.0593 in.)


Connecting Rod Big End Inside Diameter:
Mark Thickness
1 59.000 to 59.006 mm (2.32283 to 2.32307 in.)
2 59.006 to 59.012 mm (2.32307 to 2.32330 in.)
3 59.012 to 59.018 mm (2.32330 to 2.32354 in.)
4 59.018 to 59.024 mm (2.32354 to 2.32377 in.)


Crankshaft Pin Diameter:
Mark Thickness
1 55.994 to 56.000 mm (2.20448 to 2.20472 in.)
2 55.988 to 55.994 mm (2.20425 to 2.20448 in.)
3 55.982 to 55.988 mm (2.20401 to 2.20425 in.)



o.

Completely remove the Plastigage.


p.

Perform the inspection above for each cylinder.


Hide 3.REMOVE PISTON AND CONNECTING ROD

a.
A163455E09
0.906,1.75 0.906,1.521 0.906,1.521 1.521,1.156 false 0.823,1.781 1.177,2.083 0.354,0.302 10 true *1

Using a ridge reamer, remove all the carbon from the top of the cylinder.

Text in Illustration
*1 Ridge Reamer


b.

Remove the 16 cap bolts, 8 connecting rod caps and 8 lower bearings.


c.

Push the 8 pistons and 8 connecting rods through the top of the cylinder block.

HINT:
·

Keep the bearing, connecting rod and cap together.

·

Arrange the piston and connecting rods in the correct order.




Hide 13041 4.REMOVE CONNECTING ROD BEARING

a.

Remove the connecting rod bearings from the connecting rods and connecting rod caps.

HINT:

Arrange the removed parts in the correct order.



Hide 5.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A163458

Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard thrust clearance:

0.020 to 0.220 mm (0.000787 to 0.00866 in.)


Maximum thrust clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is more than the maximum, replace the thrust washers as a set. If necessary, replace the crankshaft.

Standard thrust washer thickness:

2.44 to 2.49 mm (0.0961 to 0.0980 in.)



Hide 13411 6.REMOVE CRANKSHAFT

a.
A160705E08
3.302,0.927 3.427,1.104 0.125,0.177 10 true 1 2,1.948 2.188,2.125 0.188,0.177 10 true 2 3.042,1.177 3.24,1.406 0.198,0.229 10 true 3 2.458,1.75 2.615,1.938 0.156,0.188 10 true 4 2.75,1.469 2.896,1.656 0.146,0.188 10 true 5 0.396,1.313 0.583,1.542 0.188,0.229 10 true 6 0.677,0.531 0.802,0.708 0.125,0.177 10 false 8 1.375,0.125 1.542,0.302 0.167,0.177 10 true 9 0.99,0.354 1.177,0.531 0.188,0.177 10 true 10 1.656,0.031 1.781,0.208 0.125,0.177 10 false 7

Uniformly loosen and remove the 10 bearing cap bolts and 10 seal washers in several steps in the sequence shown in the illustration.


b.
A160706E16
3.094,1.49 3.188,1.646 0.094,0.156 10 false 1 3.021,0.271 3.115,0.427 0.094,0.156 10 false 2 0.208,1.594 0.365,1.75 0.156,0.156 10 true 3 0.281,0.24 0.375,0.396 0.094,0.156 10 false 4 2.49,1.542 2.583,1.698 0.094,0.156 10 true 5 2.406,0.219 2.583,0.417 0.177,0.198 10 true 6 0.771,1.573 0.865,1.729 0.094,0.156 10 true 7 0.833,0.271 1,0.438 0.167,0.167 10 true 8 1.927,1.573 2.021,1.729 0.094,0.156 10 true 9 1.229,0.26 1.458,0.438 0.229,0.177 10 true 10 3.177,1.156 3.365,1.313 0.188,0.156 10 false 11 3.104,0.656 3.292,0.813 0.188,0.156 10 false 12 0,1.177 0.188,1.333 0.188,0.156 10 false 13 0.042,0.635 0.229,0.792 0.188,0.156 10 false 14 2.563,1.146 2.75,1.302 0.188,0.156 10 true 15 2.5,0.646 2.688,0.813 0.188,0.167 10 true 16 0.615,1.156 0.802,1.313 0.188,0.156 10 true 17 0.708,0.781 0.896,0.938 0.188,0.156 10 true 18 1.927,1.021 2.115,1.177 0.188,0.156 10 true 19 1.26,0.771 1.448,0.927 0.188,0.156 10 true 20

Uniformly loosen and remove the 20 bearing cap bolts in several steps in the sequence shown in the illustration.


c.

Using a screwdriver, slightly pry up the 5 main bearing caps.

A385334E01
1.385,0.688 1.594,0.688 1.594,0.688 2.083,1.5 true 4.792,3.021 5.031,3.021 5.031,3.021 5.031,2.781 true 4.781,3.208 4.781,2.708 true 1.198,0.615 1.521,0.875 0.323,0.26 10 false *1 4.26,2.094 4.583,2.354 0.323,0.26 10 false *2 4.719,3.271 5.042,3.531 0.323,0.26 10 false *3 6.146,2.188 6.469,2.448 0.323,0.26 10 false *4

Text in Illustration
*1 Protective Tape
*2 Cylinder Block
*3 Joint Surface
*4 Bearing Cap

NOTICE:
·

Be careful not to damage the joint surface of the cylinder block and main bearing caps.

·

Pry up the left and right side of the cap little by little.



HINT:

Tape the screwdriver tip before use.



d.

Using the 2 inside position crankshaft bearing cap bolts, loosen each crankshaft bearing cap by moving it forward and backward, and remove each crankshaft bearing cap.


e.

Remove the crankshaft.


Hide 11711 7.REMOVE CRANKSHAFT BEARING

a.

Remove the crankshaft bearings from the bearing caps and cylinder block.

HINT:

Arrange the removed parts in the correct order.



Hide 11011 8.REMOVE CRANKSHAFT THRUST WASHER SET

a.
A166548

Remove the thrust washer set from the cylinder block and No. 3 bearing cap.


Hide 15708 9.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A142804

Using a 5 mm hexagon wrench, remove the 4 bolts and 4 oil nozzles.


Hide 13011 10.REMOVE PISTON RING SET

HINT:

Arrange the piston rings in the correct order.


a.
A160692

Using a piston ring expander, remove the 2 compression rings.


b.

Remove the 2 side rails and oil ring expander by hand.


Hide 13101 11.REMOVE PISTON WITH PIN SUB-ASSEMBLY

a.

Disconnect the connecting rod from the piston.

i.
A160693

Using a small screwdriver, pry off the 2 snap rings from the piston.


ii.

Gradually heat the piston to approximately 80°C (176°F).


iii.
A142806

Using a brass bar and plastic-faced hammer, lightly tap out the piston pin. Then remove the connecting rod.

HINT:
·

The piston and pin are a matched set.

·

Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.





b.

Clean the piston.

i.

Using a gasket scraper, remove the carbon from the piston top.


ii.

Using a groove cleaning tool or broken ring, clean the piston ring grooves.


iii.

Using solvent and a brush, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.




Hide 12.REMOVE STUD BOLT

NOTICE:

If the stud bolt is deformed or its threads are damaged, replace it.