Home › Engine / Hybrid System › 3UR-FE (ENGINE MECHANICAL) › CYLINDER BLOCK › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052777 3UR-FE ENGINE MECHANICAL _0255052 CYLINDER BLOCK A

3UR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If the stud bolt is deformed or its threads are damaged, replace it.


a.

Using an E8 "TORX" socket wrench, install the stud bolts.

A163476E10
4.74,5.552 4.688,5.552 4.688,5.552 4.521,5.885 false 2.104,4.698 2,4.698 2,4.698 1.865,5 false 2.083,5.542 2.01,5.542 2.01,5.542 1.865,5.854 false 2.563,2.24 2.563,3.417 false 1.115,2.313 1.115,3.177 1.115,3.177 2.563,3.177 false 6.354,2.542 6.354,3.219 6.354,3.219 4.708,3.219 false 4.708,1.396 4.708,3.417 false 5.219,4.604 5.031,4.604 5.031,4.604 4.531,5.271 false 0.542,0.292 1.656,0.563 1.115,0.271 10 false *A 4.01,0.292 5.115,0.594 1.104,0.302 10 false *B 4.667,3.427 4.833,3.656 0.167,0.229 10 false A 2.521,3.427 2.719,3.604 0.198,0.177 10 false B 2.135,4.635 2.823,5 0.688,0.365 10 false 26.5 mm (1.04 in.) 2.083,5.469 2.813,5.844 0.729,0.375 10 false 18 mm (0.709 in.) 2.781,5.323 3.917,5.479 1.135,0.156 10 false 50 mm (1.97 in.) 1.354,6.167 1.521,6.396 0.167,0.229 10 false A 4.063,6.167 4.26,6.344 0.198,0.177 10 false B 5.49,5.302 6.188,5.677 0.698,0.375 10 false 29 mm (1.14 in.) 4.771,5.469 5.458,5.844 0.688,0.375 10 false 13 mm (0.512 in.) 5.25,4.531 6.406,4.74 1.156,0.208 10 false 14 mm (0.551 in.)

Text in Illustration
*A Upper Side *B Lower Side

Torque:
for stud bolt A : 20 N*m (204 kgf*cm, 15 ft.*lbf)
for stud bolt B : 9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 15708 2.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Using a 5 mm hexagon wrench, install the 4 oil nozzles with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13101 3.INSTALL PISTON WITH PIN SUB-ASSEMBLY

a.
A160714E04
1.458,1.708 1.948,1.708 1.948,1.708 2.302,1.458 false 1.25,1.625 1.438,1.813 0.188,0.188 10 false *1

Using a small screwdriver, install a new snap ring at one end of the piston pin hole.

Text in Illustration
*1 Service Hole

HINT:

Be sure that the end gap of the snap ring is not aligned with the service hole of the piston.



b.

Gradually heat the piston to approximately 80°C (176°F).


c.

Coat the piston pin and connecting rod with engine oil.


d.
A160715E07
0.938,3.271 0.938,4.167 false 0.948,1.146 1.354,1.844 1.354,1.844 1.521,1.844 false 2.667,0.604 2.365,0.604 false 2.969,2.625 2.375,2.625 false 0.042,0 0.417,0.24 0.375,0.24 10 false *A 0.042,2.146 0.438,2.365 0.396,0.219 10 false *B 2.156,0.5 2.333,0.688 0.177,0.188 10 false *1 1.542,1.76 1.719,1.948 0.177,0.188 10 false *1 2.167,2.542 2.344,2.729 0.177,0.188 10 false *1 0.844,4.219 1.021,4.406 0.177,0.188 10 false *1

Align the front marks of the piston and connecting rod as shown in the illustration. Then push in the piston pin with your thumb until the piston pin contacts the snap ring.

Text in Illustration
*A LH
*B RH
*1 Front Mark

NOTICE:

For the LH side, perform the assembly so that the front marks of the piston and connecting rod are on the same side. For the RH side, perform the assembly so that the front marks of the piston and connecting rod are on opposite sides.


HINT:

The piston and pin are a matched set.



e.

Check the fitting condition between the piston and piston pin.

i.

Move the connecting rod back and forth on the piston pin. Check the fitting condition.

If abnormal movement is felt, replace the piston and pin as a set.


ii.

Rotate the piston back and forth on the piston pin. Check the fitting condition.

If abnormal movement is felt, replace the piston and pin as a set.



f.
A160714E05
1.438,1.667 1.927,1.667 1.927,1.667 2.281,1.417 false 1.219,1.583 1.406,1.771 0.188,0.188 10 false *1

Using a small screwdriver, install a new snap ring at the other end of the piston pin hole.

Text in Illustration
*1 Service Hole

HINT:

Be sure that the end gap of the snap ring is not aligned with the service hole of the piston.



Hide 13011 4.INSTALL PISTON RING SET

a.
A164414E12
1.521,0.594 1.698,0.594 1.698,0.594 1.917,0.896 false 1.521,1.667 1.677,1.667 1.677,1.667 1.792,1.385 false 1.99,1.146 2.604,1.385 2.604,1.385 2.604,1.521 false 1.271,0.5 1.479,0.677 0.208,0.177 10 false *1 1.271,1.583 1.469,1.76 0.198,0.177 10 false *2 2.5,1.552 2.698,1.729 0.198,0.177 10 false *3

Install the oil ring expander and 2 side rails by hand.

Text in Illustration
*1 Side Rail Upper
*2 Side Rail Lower
*3 Oil Ring Expander


b.
A273220E05
1.771,2.813 1.573,2.813 1.573,2.813 1.229,3.052 false 2.958,3.531 2.802,3.531 2.802,3.531 2.646,3.313 false 3.063,2.156 2.917,2.156 2.917,2.156 2.729,2.417 false 1.25,3.427 1.583,2.813 false 2.573,4.177 2.354,4.479 2.354,4.479 2.208,4.479 false 1.083,4.188 0.875,4.479 0.875,4.479 0.74,4.479 false 0.469,4.385 0.708,4.573 0.24,0.188 10 false *1 3.115,2.042 3.354,2.229 0.24,0.188 10 false *1 1.958,4.396 2.198,4.583 0.24,0.188 10 false *2 3.021,3.448 3.26,3.635 0.24,0.188 10 false *2 1.813,2.719 2.052,2.906 0.24,0.188 10 false *3

Using a piston ring expander, install the 2 compression rings so that the paint marks are positioned as shown in the illustration.

Paint Mark:
Item Paint Mark
No. 1 compression ring Yellow
No. 2 compression ring Green


Text in Illustration
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Paint Mark
V100135

Top


Hide 11711 5.INSTALL CRANKSHAFT BEARING

a.
A124282E32
0.781,0.5 1.063,0.698 0.281,0.198 10 false *1 2.563,0.49 2.813,0.688 0.25,0.198 10 false *2 0.615,2.615 1.219,2.802 0.604,0.188 10 false 22.5 mm 2.469,2.604 2.927,2.792 0.458,0.188 10 false 21 mm

Clean the main journal and both surfaces of the bearing.


b.

Install the upper bearing.

Text in Illustration
*1 No. 1 and No. 5 Journal Bearings
*2 No. 2, No. 3 and No. 4 Journal Bearings

NOTICE:

Main bearings come in widths of 21 mm (0.827 in.) and 22.5 mm (0.886 in.). Install the 22.5 mm (0.886 in.) bearings in the No. 1 and No. 5 cylinder block journal positions with the main bearing caps. Install the 21 mm (0.827 in.) bearings in the No. 2, No. 3 and No. 4 positions.


i.
A142825E03
1.636,3.87 1.866,4.072 0.230,0.202 10 *a 2.605,3.87 2.835,4.058 0.230,0.188 10 *b

Install the upper bearing to the cylinder block as shown in the illustration.

Text in Illustration
*a CORRECT
*b INCORRECT

NOTICE:
·

Do not apply engine oil to the bearings and the contact surfaces.

·

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.

·

Do not allow coolant to come into contact with the bearing inner surface.

·

If any coolant comes into contact with the bearing inner surface, replace the bearing with a new one.





c.
A149045E13
2.458,3.396 2.771,3.604 2.771,3.604 2.771,4.01 false 2.646,4.073 2.844,4.26 0.198,0.188 10 false *1 0.729,3.563 0.844,3.74 0.115,0.177 10 false A 2.177,3.604 2.302,3.781 0.125,0.177 10 false B

Install the lower bearing.

NOTICE:
·

Be sure to install the selected bearing.

·

Main bearings come in widths of 21 mm (0.827 in.) and 22.5 mm (0.886 in.). Install the 22.5 mm (0.886 in.) bearings in the No. 1 and No. 5 cylinder block journal positions with the main bearing caps. Install the 21 mm (0.827 in.) bearings in the No. 2, No. 3 and No. 4 positions.



i.

Install the lower bearings to the crankshaft bearing caps.


ii.

Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and the lower bearing edge.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)


Text in Illustration
*1 Vernier Caliper

NOTICE:
·

Do not apply engine oil to the bearings and the contact surfaces.

·

Do not allow coolant to come into contact with the bearing inner surface.

·

If any coolant comes into contact with the bearing inner surface, replace the bearing with a new one.





Hide 11011 6.INSTALL CRANKSHAFT THRUST WASHER SET

a.

Apply engine oil to the thrust washer set.


b.

Install the 4 thrust washers to the No. 3 journal position of the cylinder block and crankshaft bearing cap with the oil grooves facing outward.


Hide 13411 7.INSTALL CRANKSHAFT

a.
U162863E02
1.813,2.708 1.813,3.042 false 2.313,2.896 2.313,2.708 false 1.344,2.896 1.344,2.708 false 1.719,3.073 1.927,3.25 0.208,0.177 10 false *1

Apply engine oil to the upper bearing and lower bearing, then place the crankshaft on the cylinder block.


b.

Confirm the front marks and numbers of the crankshaft bearing caps, and install the crankshaft bearing caps on the cylinder block.

Text in Illustration
*1 Number Mark

HINT:

A number is marked on each main bearing cap to indicate the installation position.



c.

Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.


d.

Temporarily install the 10 crankshaft bearing cap bolts to the inside positions.


e.
A160709E05
0.76,2.854 0.76,2.688 0.76,2.688 1.156,2.219 false 2.188,2.896 2.646,3.052 0.458,0.156 10 false 91 mm 0.667,2.885 0.854,3.094 0.188,0.208 10 false *a

Push the crankshaft bearing cap by hand until the clearance between the crankshaft bearing cap and cylinder block is less than 6 mm (0.236 in.).

Bolt length:

91 mm (3.58 in.)


Text in Illustration
*a Less than 6 mm


f.
U115329

Using a plastic-faced hammer, lightly tap the crankshaft bearing cap to ensure a proper fit.


g.

Apply a light coat of engine oil to the threads and under the heads of the 10 crankshaft bearing cap bolts.


h.
A160710E04
1.667,3.104 2.24,3.281 0.573,0.177 10 false 79.5 mm

Temporarily install the 10 crankshaft bearing cap bolts to the outside positions.

Bolt length:

79.5 mm (3.13 in.)


HINT:

The main bearing cap bolts are tightened in 2 progressive steps.



i.

Step 1:

i.
A160706E17
1.313,0.781 1.406,0.938 0.094,0.156 10 true 1 2.052,1.146 2.146,1.302 0.094,0.156 10 true 2 0.719,0.635 0.833,0.792 0.115,0.156 10 true 3 0.677,1.156 0.771,1.313 0.094,0.156 10 true 4 2.552,0.646 2.646,0.802 0.094,0.156 10 true 5 2.583,1.146 2.677,1.302 0.094,0.156 10 true 6 0.146,0.656 0.24,0.813 0.094,0.156 10 true 7 0.094,1.167 0.188,1.323 0.094,0.156 10 true 8 3.125,0.656 3.219,0.813 0.094,0.156 10 false 9 3.167,1.146 3.354,1.302 0.188,0.156 10 false 10 1.375,0.198 1.563,0.354 0.188,0.156 10 true 11 1.823,1.615 2.01,1.771 0.188,0.156 10 true 12 0.792,0.219 0.979,0.375 0.188,0.156 10 true 13 0.729,1.594 0.917,1.75 0.188,0.156 10 true 14 2.313,0.208 2.5,0.365 0.188,0.156 10 true 15 2.406,1.625 2.594,1.781 0.188,0.156 10 true 16 0.177,0.313 0.365,0.469 0.188,0.156 10 false 17 0.083,1.521 0.271,1.677 0.188,0.156 10 false 18 3,0.281 3.188,0.438 0.188,0.156 10 true 19 3.083,1.5 3.271,1.656 0.188,0.156 10 true 20

Uniformly tighten the 20 crankshaft bearing cap bolts in the sequence shown in the illustration.

Torque:
for inside position : 61 N*m (622 kgf*cm, 45 ft.*lbf)
for outside position : 27 N*m (275 kgf*cm, 20 ft.*lbf)

If any of the main bearing cap bolts does not meet the specified torque, replace it.



j.

Step 2:

i.

Mark the front of the bearing cap bolts with paint.


ii.

Tighten the bearing cap bolts 90° in the order shown in step 1.


iii.

Check that the painted marks are now at a 90° angle to the front.



k.

Check that the crankshaft turns smoothly.


l.
A160711E09
0.885,0.198 0.99,0.344 0.104,0.146 10 false 1 1.167,0.073 1.271,0.219 0.104,0.146 10 false 2 0.521,0.406 0.625,0.552 0.104,0.146 10 false 3 1.479,0.021 1.583,0.167 0.104,0.146 10 false 4 0.135,0.604 0.24,0.75 0.104,0.146 10 false 5 2.542,1.51 2.646,1.656 0.104,0.146 10 true 6 2.24,1.771 2.375,1.938 0.135,0.167 10 true 7 2.74,1.313 2.844,1.458 0.104,0.146 10 true 8 1.365,1.99 1.552,2.167 0.188,0.177 10 true 9 3.146,0.875 3.323,1.021 0.177,0.146 10 true 10

Install and uniformly tighten the 10 crankshaft bearing cap bolts and 10 new seal washers in several steps in the sequence shown in the illustration.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


m.

Check that the crankshaft turns smoothly.


Hide 13041 8.INSTALL CONNECTING ROD BEARING

A149047E03
0.833,2.302 0.729,2.302 0.729,2.302 0.396,3.625 false 1.875,3.542 1.99,3.708 0.115,0.167 10 false A 3.104,3.542 3.26,3.719 0.156,0.177 10 false B 0.875,2.219 1.104,2.427 0.229,0.208 10 false *1

a.

Install the connecting rod bearings to the connecting rods and bearing caps.


b.

Using a vernier caliper, measure the distance between the connecting rod and bearing cap edges, and each connecting rod bearing edge.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)


Text in Illustration
*1 Vernier Caliper

NOTICE:
·

Do not apply engine oil to the bearings and the contact surfaces.

·

Do not allow coolant to come into contact with the bearing inner surface.

·

If any coolant comes into contact with the bearing inner surface, replace the bearing with a new one.




Hide 9.INSTALL PISTON AND CONNECTING ROD

a.
U162972E02
0.938,1.146 1.042,1.146 1.042,1.146 1.802,2.24 false 1.573,0.427 1.802,0.594 0.229,0.167 10 false *1 0.677,1.063 0.885,1.229 0.208,0.167 10 false *3 0.729,2.365 0.927,2.531 0.198,0.167 10 false *5 2.427,2.333 2.625,2.51 0.198,0.177 10 false *2 2.698,1.313 2.885,1.49 0.188,0.177 10 false *4

Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.


b.

Position the piston rings so that the ring ends are as shown in the illustration.

Text in Illustration
*1 Side Rail Upper
*2 Side Rail Lower
*3 Front Mark
*4 No. 1 Ring
*5 No. 2 Ring

NOTICE:

Do not align the ring ends.


HINT:

The expander ends can be placed anywhere.



c.
A163492E04
0.066,1.846 0.385,2.095 0.318,0.250 10 *A 0.066,3.239 0.394,3.482 0.328,0.243 10 *B 0.805,2.603 1.002,2.783 0.198,0.180 10 *1 0.82,3.953 1.008,4.163 0.188,0.209 10 *1 2.826,3.772 3.024,3.964 0.198,0.192 10 *1 2.949,3.103 2.949,3.725 false 1.04,4.031 1.201,4.031 1.201,4.031 1.541,4.257 false 1.039,2.682 1.212,2.682 1.212,2.682 1.541,2.852 false

Using a hammer handle and piston ring compressor, push the correctly numbered piston and connecting rod into the cylinder with the front mark of the piston facing forward.

Text in Illustration
*A LH
*B RH
*1 Front Mark


d.

Place the connecting rod cap on the connecting rod.

i.
A163494E09
1.875,0.635 1.198,1.146 1.198,1.146 0.896,1.146 false 0.677,1.073 0.885,1.281 0.208,0.208 10 true *1

Match the numbered connecting rod cap with the connecting rod.


ii.

Place the connecting rod cap on the connecting rod, and check that the front mark of the connecting rod cap is facing the direction indicated in the chart below.

Front Mark:
Item Front Mark
Bank 1 Front side
Bank 2 Rear side


Text in Illustration
*1 Front Mark
V100135

Front



e.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


f.

Temporarily install the connecting rod cap bolts.

HINT:

The connecting rod cap bolts are tightened in 2 progressive steps.



g.

Step 1:

i.
A163495

Install and alternately tighten the bolts of the connecting rod cap in several steps.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)



h.

Step 2:

i.

Mark the front side of each connecting rod cap bolt with paint.


ii.

Tighten the cap bolts 90° as shown in the illustration in the order in step 1.


iii.

Check that the painted marks are now at a 90° angle to the front.



i.

Check that the crankshaft turns smoothly.