Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › CYLINDER HEAD
RM2660E _51 Engine / Hybrid System _052778 1GR-FE ENGINE MECHANICAL _0255056 CYLINDER HEAD A

1GR-FE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL UNION

NOTICE:

If a union is deformed, replace it.


a.

Apply adhesive to 2 or 3 threads of the bolt ends of unions.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.

Using a 12 mm deep socket wrench, install the 2 unions.

Torque:
15 N*m (150 kgf*cm, 11 ft.*lbf)

A222133E03
0.198,0.001 0.425,0.208 0.228,0.207 10 *a 3.969,0.001 4.197,0.208 0.228,0.207 10 *b 2.189,2.131 3.289,2.342 1.100,0.211 10 67 mm (2.64 in.) 5.851,2.137 6.951,2.349 1.100,0.211 10 30 mm (1.18 in.)

Text in Illustration
*a Front Side of RH *b Intake Side of LH


Hide 2.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using E6 and E8 "TORX" sockets, install the stud bolts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 4.0 N*m (41 kgf*cm, 35 in.*lbf)

U163346E01
0.489,1.566 0.649,1.767 0.160,0.201 10 A 0.537,1.096 0.537,1.558 false 2.739,1.543 2.899,1.744 0.160,0.201 10 A 2.786,1.074 2.786,1.535 false 4.024,1.569 4.183,1.770 0.160,0.201 10 A 4.071,1.1 4.071,1.561 false 6.223,1.5 6.383,1.701 0.160,0.201 10 A 6.27,1.03 6.27,1.492 false 1.858,3.518 2.018,3.693 0.160,0.175 10 A 1.734,3.264 1.734,3.405 false 2.115,3.264 2.115,3.405 false 1.307,2.665 1.307,3.405 false 2.124,2.641 2.304,2.802 2.304,2.802 2.304,3.405 false 1.905,3.405 1.905,3.511 false 5.592,3.55 5.752,3.726 0.160,0.175 10 A 5.448,3.304 5.448,3.442 false 5.821,3.312 5.821,3.442 false 5.034,2.761 5.034,3.442 false 5.828,2.725 6.038,2.898 6.038,2.898 6.038,3.442 false 5.639,3.442 5.639,3.548 false 1.3,4.979 1.432,5.149 0.132,0.170 10 B 1.341,4.77 1.341,4.967 false 1.014,4.436 1.014,4.901 1.014,4.901 1.341,4.901 false 5.666,5.084 5.791,5.251 0.125,0.167 10 B 5.706,4.844 5.706,5.075 false 6.031,4.51 6.031,4.98 6.031,4.98 5.706,4.98 false 0.854,6.258 1.341,6.462 0.487,0.204 10 A (M8) 5.334,6.258 5.805,6.460 0.471,0.201 10 B (M6) 1.877,5.72 2.959,5.922 1.082,0.202 10 35 mm (1.38 in.) 1.903,5.055 3.072,5.258 1.169,0.203 10 20 mm (0.787 in.) 1.777,6.33 2.970,6.548 1.193,0.218 10 13 mm (0.512 in.) 5.998,5.206 7.153,5.425 1.156,0.218 10 16 mm (0.630 in.) 6.339,5.684 6.972,6.072 0.633,0.387 10 27 mm (1.06 in.) 6.093,6.295 7.145,6.536 1.052,0.242 10 9 mm (0.354 in.) 1.866,5.125 1.743,5.125 1.743,5.125 1.327,5.505 false 1.754,6.408 1.628,6.408 1.628,6.408 1.327,6.026 false 5.785,5.665 5.904,5.286 5.904,5.286 5.984,5.286 false 5.785,6.061 5.984,6.366 5.984,6.366 6.064,6.366 false 1.547,0.277 1.775,0.463 0.228,0.186 10 *a 5.114,0.292 5.342,0.478 0.228,0.186 10 *b 1.547,2.146 1.775,2.332 0.228,0.186 10 *c 5.237,2.146 5.465,2.332 0.228,0.186 10 *d 1.614,3.703 1.842,3.889 0.228,0.186 10 *e 5.198,3.793 5.425,3.979 0.228,0.186 10 *f

Text in Illustration
*a Intake Side of RH *b Intake Side of LH
*c Exhaust Side of RH *d Exhaust Side of LH
*e Rear Side of RH *f Rear Side of LH


Hide 11117F 3.INSTALL NO. 2 STRAIGHT SCREW PLUG

a.

Using a 14 mm hexagon wrench, install 2 new gaskets and the 2 No. 2 straight screw plugs.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


Hide 11117E 4.INSTALL NO. 1 STRAIGHT SCREW PLUG

a.

Using a 10 mm hexagon wrench, install 4 new gaskets and the 4 No. 1 straight screw plugs.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 13734 5.INSTALL VALVE SPRING SEAT

a.

Install the valve spring seats to the cylinder head.


Hide 13711E 6.INSTALL VALVE STEM OIL SEAL

a.
A385870E01
0.563,0.719 0.656,0.406 0.656,0.406 0.875,0.406 false 2.469,0.698 2.563,0.385 2.563,0.385 2.781,0.385 false 2.833,0.302 3.146,0.5 0.313,0.198 10 false *2 0.948,0.323 1.26,0.521 0.313,0.198 10 false *1 0.646,1.708 0.958,1.906 0.313,0.198 10 false *a 2.688,1.698 3,1.896 0.313,0.198 10 false *b

Apply a light coat of engine oil to new valve stem oil seals.

Text in Illustration
*1 Gray
*2 Black
*a Intake Side
*b Exhaust Side

NOTICE:

Pay attention when installing the intake and exhaust valve stem oil seals. For example, installing the intake valve stem oil seal to the exhaust side or installing the exhaust valve stem oil seal to the intake side can cause installation problems later.


HINT:

The intake valve oil seals are gray and the exhaust valve oil seals are black.



b.
A124592E04
1.026,2.09 1.248,2.270 0.222,0.180 10 *a 2.31,2.09 2.522,2.264 0.211,0.173 10 *b 0.106,0.058 0.877,0.412 0.770,0.354 10 SST 1.409,0.68 0.815,0.144 0.815,0.144 0.484,0.144 false

Using SST, push in the oil seals.

SST
09201-41020  

Text in Illustration
*a CORRECT
*b INCORRECT

NOTICE:

Failure to use SST will cause the seal to be damaged or improperly seated.



Hide 13711 7.INSTALL INTAKE VALVE

a.
A385871E01
2.698,1.594 3.01,1.792 0.313,0.198 10 false *a

Apply a sufficient coat of engine oil to the tip area of the intake valve shown in the illustration.

Text in Illustration
*a 30 mm (1.18 in.) or more


b.

Install the intake valve, inner compression spring and valve spring retainer to the cylinder head.

NOTICE:

Install the same parts in the same combination to their original locations.



c.
A221102E01
1.925,0.138 2.269,0.328 0.343,0.191 10 SST 1.893,0.221 1.779,0.221 1.779,0.221 1.5,0.521 false

Using SST, compress the inner compression spring and install the 2 valve spring retainer locks.

SST
09202-70020  (09202-00010)


d.

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the retainer.



Hide 13715 8.INSTALL EXHAUST VALVE

a.
A385871E01
2.698,1.594 3.01,1.792 0.313,0.198 10 false *a

Apply a sufficient coat of engine oil to the tip area of the exhaust valve shown in the illustration.

Text in Illustration
*a 30 mm (1.18 in.) or more


b.

Install the exhaust valve, inner compression spring and valve spring retainer to the cylinder head.

NOTICE:

Install the same parts in the same combination to the original locations.



c.
A221103E01
1.635,0.09 1.947,0.272 0.312,0.182 10 SST 2.017,0.173 2.163,0.173 2.163,0.173 2.386,0.463 false

Using SST, compress the inner compression spring and install the 2 valve spring retainer locks.

SST
09202-70020  (09202-00010)


d.

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the retainer.