1.CLEAN CYLINDER BLOCK SUB-ASSEMBLY
Using a gasket scraper, remove all the gasket material from the top surface of the cylinder block.
Using a soft brush and solvent, thoroughly clean the cylinder block.
If the cylinder is washed at high temperatures, the cylinder liner sticks out beyond the cylinder block. Always wash the cylinder block at a temperature of 45°C (113°F) or less.
2.INSPECT CYLINDER BLOCK FOR WARPAGE
Using a precision straightedge and feeler gauge, measure the warpage of the surfaces which contact the cylinder head gaskets.
0.05 mm (0.00197 in.)
If the warpage is more than the maximum, replace the cylinder block.
Visually check the cylinder for vertical scratches. If deep scratches are present, rebore all 6 cylinders.
If necessary, replace the cylinder block.
3.INSPECT CYLINDER BORE
Using a cylinder gauge, measure the cylinder bore diameter at positions A and B in the thrust and axial directions.
94.000 to 94.012 mm (3.7008 to 3.7013 in.)
94.132 mm (3.7060 in.)
10 mm (0.394 in.)
| *1 | Axial Direction |
| *2 | Thrust Direction |
| *3 | Center |
|
Engine Front |
If the diameter is more than the maximum, replace the cylinder block.
4.INSPECT RING GROOVE CLEARANCE
Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.
| Item | Specified Condition |
|---|---|
| No. 1 compression ring | 0.02 to 0.07 mm (0.000787 to 0.00276 in.) |
| No. 2 compression ring | 0.02 to 0.06 mm (0.000787 to 0.00236 in.) |
| Oil ring | 0.07 to 0.15 mm (0.00276 to 0.00590 in.) |
If the clearance is not as specified, replace the piston with pin sub-assembly.
5.INSPECT PISTON RING END GAP
Insert the piston ring into the cylinder bore.
Using a piston, push the piston ring a little beyond the bottom of the ring travel, 110 mm (4.33 in.) from the top of the cylinder block.
Using a feeler gauge, measure the end gap.
| Item | Specified Condition |
|---|---|
| No. 1 compression ring | 0.22 to 0.32 mm (0.00866 to 0.0126 in.) |
| No. 2 compression ring | 0.35 to 0.45 mm (0.0138 to 0.0177 in.) |
| Oil ring (side rail) | 0.10 to 0.40 mm (0.00394 to 0.0157 in.) |
| Item | Specified Condition |
|---|---|
| No. 1 compression ring | 1.0 mm (0.0394 in.) |
| No. 2 compression ring | 1.1 mm (0.0433 in.) |
| Oil ring (side rail) | 1.0 mm (0.0394 in.) |
If the end gap is more than the maximum, replace the piston ring. If the end gap is more than the maximum even with a new piston ring, rebore all 6 cylinders or replace the cylinder block sub-assembly.
6.CLEAN PISTON WITH PIN SUB-ASSEMBLY
Clean the piston.
Using a gasket scraper, remove the carbon from the piston top.
Using a groove cleaning tool or broken ring, clean the piston ring grooves.
Using solvent and a brush, thoroughly clean the piston.
Do not use a wire brush.
7.INSPECT PISTON OIL CLEARANCE
Using a micrometer, measure the piston diameter at a position that is 9.6 mm (0.378 in.) from the bottom of the piston (refer to the illustration).
93.961 to 93.991 mm (3.6992 to 3.7004 in.)
Subtract the piston diameter measurement from the cylinder bore diameter measurement.
0.009 to 0.051 mm (0.000354 to 0.00201 in.)
0.110 mm (0.00433 in.)
If the oil clearance is more than the maximum, replace all 6 pistons. If necessary, replace the cylinder block.
8.INSPECT PISTON PIN OIL CLEARANCE
Check each mark on the piston and connecting rod.
| *1 | Front Mark |
| *2 | Position Pin Hole Inside Diameter Mark |
| *3 | Connecting Rod Bush Inside Diameter Mark |
Using a caliper gauge, measure the inside diameter of the piston pin hole.
| Item | Specified Condition |
|---|---|
| Mark A | 22.001 to 22.004 mm (0.86618 to 0.86630 in.) |
| Mark B | 22.005 to 22.007 mm (0.86634 to 0.86642 in.) |
| Mark C | 22.008 to 22.010 mm (0.86645 to 0.86653 in.) |
Using a micrometer, measure the piston pin diameter.
| Measurement Position | Piston Pin Position |
|---|---|
| a | 28 mm (1.102 in.) from edge |
| b | 5 mm (0.197 in.) from edge |
| Item | Specified Condition |
|---|---|
| Mark A | 21.997 to 22.000 mm (0.86602 to 0.86614 in.) |
| Mark B | 22.001 to 22.003 mm (0.86618 to 0.86626 in.) |
| Mark C | 22.004 to 22.006 mm (0.86630 to 0.86642 in.) |
Using a caliper gauge, measure the inside diameter of the connecting rod bush.
| Item | Specified Condition |
|---|---|
| Mark A | 22.005 to 22.008 mm (0.86634 to 0.86645 in.) |
| Mark B | 22.009 to 22.011 mm (0.86649 to 0.86657 in.) |
| Mark C | 22.012 to 22.014 mm (0.86661 to 0.86669 in.) |
Subtract the piston pin diameter measurement from the piston pin hole diameter measurement.
0.001 to 0.007 mm (0.0000394 to 0.000276 in.)
0.040 mm (0.00157 in.)
If the oil clearance is more than the maximum, replace the piston with pin sub-assembly.
Subtract the piston pin diameter measurement from the bush inside diameter measurement.
0.005 to 0.011 mm (0.000197 to 0.000433 in.)
0.050 mm (0.00197 in.)
If the oil clearance is more than the maximum, replace the connecting rod sub-assembly. If necessary, replace the piston with pin sub-assembly.
9.INSPECT CONNECTING ROD SUB-ASSEMBLY
Using a rod aligner and feeler gauge, check the connecting rod alignment.
Check for bend.
0.05 mm (0.00197 in.) per 100 mm (3.94 in.)
If the bend is more than the maximum, replace the connecting rod sub-assembly.
Check for twist.
0.15 mm (0.00591 in.) per 100 mm (3.94 in.)
If the twist is more than the maximum, replace the connecting rod sub-assembly.
13411
10.INSPECT CRANKSHAFT
Using a dial indicator, measure the runout at the center journal.
0.06 mm (0.00236 in.)
If the circle runout is more than the maximum, replace the crankshaft.
Using a micrometer, measure the diameter of each main journal.
71.988 to 72.000 mm (2.8342 to 2.8346 in.)
If the diameter is not as specified, check the oil clearance. If necessary, replace the crankshaft.
Check each main journal for taper and out-of-round as shown in the illustration.
0.02 mm (0.000787 in.)
If the taper and out-of-round is more than the maximum, replace the crankshaft.
Using a micrometer, measure the diameter of each crank pin.
55.992 to 56.000 mm (2.2044 to 2.2047 in.)
If the diameter is not as specified, check the oil clearance. If necessary, replace the crankshaft.
Check each crank pin for taper and out-of-round as shown in the illustration.
0.02 mm (0.000787 in.)
If the taper and out-of-round is more than the maximum, replace the crankshaft.
13265
11.INSPECT CONNECTING ROD BOLT
Using a vernier caliper, measure the tension portion diameter of the bolt.
7.2 to 7.3 mm (0.283 to 0.287 in.)
7.0 mm (0.276 in.)
| *1 | Measurement Area |
If the diameter is less than the minimum, replace the connecting rod bolt.
11416
12.INSPECT CRANKSHAFT BEARING CAP SET BOLT
Using a vernier caliper, measure the thread outside diameter of the crankshaft bearing cap set bolt.
10.0 to 10.2 mm (0.394 to 0.402 in.)
| *1 | Measurement Area |
If the result is not as specified, replace the crankshaft bearing cap set bolt.
13.INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY
Push the check valve with a pin to check if it is stuck. If stuck, replace the oil nozzle.
Push the check valve with a pin to check if it moves smoothly.
If it does not move smoothly, clean or replace the oil nozzle.
While covering A, blow air into B. Check that air does not leak through C. Perform the check again while covering B and blowing air into A.
If air leaks, clean or replace the oil nozzle.
Push the check valve while covering A, and blow air into B. Check that air passes through C. Perform the check again while covering B, pushing the check valve and blowing air into A.
If air does not pass through C, clean or replace the oil nozzle.