Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › CYLINDER HEAD
RM2660E _51 Engine / Hybrid System _052779 1VD-FTV ENGINE MECHANICAL _0255071 CYLINDER HEAD A

1VD-FTV ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE VALVE GUIDE BUSH

a.
A164872

Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on a wooden block.


c.
A164547E03
2.865,0.229 2.5,0.229 true 1.281,1.177 0.958,1.177 true 1.25,0.656 0.958,0.656 0.958,0.656 0.958,1.75 true 0.781,1.823 1.188,2.042 0.406,0.219 10 true SST 2.917,0.156 3.24,0.323 0.323,0.167 10 false SST

Using SST, tap out the valve guide bush.

SST
09201-10000  (09201-01060)
09950-70010  (09951-07100)


d.
A164581E03
0.24,1.708 1.26,1.938 1.021,0.229 10 true Bore Diameter

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard bush bore diameter:

10.985 to 11.006 mm (0.432 to 0.433 in.)


If the bush bore diameter of the cylinder head is more than 11.006 mm (0.433 in.), machine the bush bore to the dimension of 11.035 to 11.056 mm (0.434 to 0.435 in.).

Standard Valve Guide Bush Diameter:
Item Specified Condition
STD 11.033 to 11.044 mm (0.434 to 0.435 in.)
O/S 0.05 11.083 to 11.094 mm (0.436 to 0.437 in.)


If the bush bore diameter of the cylinder head is more than 11.056 mm (0.435 in.), replace the cylinder head sub-assembly.


e.
A164872

Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).


f.

Place the cylinder head on a wooden block.


g.
U162924E02
1.24,0.656 0.979,0.656 0.979,0.656 0.979,1.531 true 1.271,1.198 0.979,1.198 true 3.083,0.594 3.24,0.76 0.156,0.167 10 false A 0.833,1.583 1.219,1.938 0.385,0.354 10 true SST

Using SST, tap in a new valve guide bush to the specified protrusion height A shown in the illustration.

SST
09201-10000  (09201-01060)
09950-70010  (09951-07100)

Standard protrusion height:

9.0 to 9.4 mm (0.354 to 0.370 in.)



h.
A385767

Using a sharp 6.0 mm reamer, ream the valve guide bush to obtain the standard specified clearance between the valve guide bush and valve stem.

Standard Overall Length:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.035 to 0.070 mm (0.00138 to 0.00276 in.)



Hide 11117E 2.REPLACE HEAD STRAIGHT SCREW PLUG

a.
A164575E01
0.058,0 0.333,0.163 0.275,0.163 10 RH: 0.058,2.394 0.312,2.556 0.254,0.163 10 LH:

Using a 6 mm hexagon wrench, remove the straight screw plug and gasket.


b.

Using a 6 mm hexagon wrench, install a new gasket and straight screw plug.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 11155A 3.REPLACE RING PIN

A385744E01
0.115,0.115 1.792,0.365 1.677,0.25 12 false Cylinder Head Side: 0.125,2.021 1.802,2.271 1.677,0.25 12 false Intake Manifold Side: 5.771,1.76 6.677,1.948 0.906,0.188 10 false 4.4 to 5.6 mm

HINT:

It is not necessary to remove the ring pin unless it is being replaced.


a.

Remove the ring pins.


b.

Using a plastic-faced hammer, tap in new ring pins.

Standard protrusion:

4.4 to 5.6 mm (0.173 to 0.220 in.)



Hide 17141J 4.REPLACE STUD BOLT

A164548

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.

Using an E8 "TORX" wrench, remove the stud bolts.


b.

Using an E8 "TORX" wrench, install new stud bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)