Home › Engine / Hybrid System › 1GR-FE (FUEL) › FUEL SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052780 1GR-FE FUEL _0255075 FUEL SYSTEM L

1GR-FE FUEL  FUEL SYSTEM  PRECAUTION  


CAUTION:
·

Before working on the fuel system, disconnect the cable from the negative (-) battery terminal.

·

Do not smoke or be near an open flame when working on the fuel system.

·

Keep gasoline away from rubber and leather parts.



IGNITION SWITCH EXPRESSION


a.

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.



a.

Disconnect the fuel pump ECU connector (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL PUMP ECU>REMOVAL).


b.

Start the engine. After the engine has stopped on its own, turn the engine switch off.

HINT:

If DTC P0230 is output, clear the DTC (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).



c.

Crank the engine, and then check that the engine does not start.


d.

Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.


e.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




f.

Connect the fuel pump ECU connector (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL PUMP ECU>INSTALLATION).



FUEL SYSTEM


a.

When disconnecting the high fuel pressure line, a large amount of gasoline will spill out. Follow these procedures.

i.

Discharge the fuel system pressure.


ii.

Put a container under the connecting part of the pressure line.


iii.

Slowly loosen the connection.


iv.

Disconnect the connection.


v.

Plug the connection with a rubber plug.



b.
A223032E04
3.068,0.244 3.338,0.403 0.270,0.159 10 *a 3.068,0.906 3.338,1.065 0.270,0.159 10 *b 3.068,1.559 3.338,1.718 0.270,0.159 10 *b

Observe these precautions when removing and installing the injectors.

Text in Illustration
*a OK
*b NG

i.

Never reuse the O-ring.


ii.

When installing a new O-ring to the injector, do not damage it.


iii.

Coat new O-rings with spindle oil or gasoline before installing. Do not use engine oil, gear oil or brake oil.



c.
A223033E01
1.752,0.472 1.473,0.193 1.473,0.193 1.344,0.193 false 1.135,0.109 1.314,0.269 0.178,0.160 10 *1

Install the injector to the delivery pipe and lower intake manifold as shown in the illustration.

Text in Illustration
*1 O-Ring

NOTICE:

Before installing the injector, be sure to apply spindle oil or gasoline to the place where the delivery pipe or cylinder head contacts the O-ring of the injector.



d.

Observe these precautions when disconnecting the fuel tube connector (for quick type A).

i.
A181442E02
1.797,0.674 1.990,0.857 0.193,0.184 10 *1 2.573,2.495 2.765,2.679 0.192,0.184 10 *1 1.781,0.766 1.669,0.766 1.669,0.766 1.591,1.324 false 2.55,2.592 2.463,2.592 2.463,2.592 2.111,2.868 false

Fuel Pipe Clamp Type:

Remove the fuel pipe clamp from the fuel tube connector.

Text in Illustration
*1 Fuel Pipe Clamp


ii.
A157617E17
1.917,0.354 1.719,0.354 1.719,0.354 1.552,0.969 false 1.969,0.281 2.198,0.479 0.229,0.198 10 false *1

Fuel Hose Connector Cover Type:

Detach the lock claw by lifting up the cover as shown in the illustration.

Text in Illustration
*1 Fuel Hose Connector Cover
V100135

Pull


iii.

Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.


iv.
A088336E58
3.021,0.885 2.896,0.885 2.896,0.885 2.458,1.156 false 3.063,0.781 3.25,0.958 0.188,0.177 10 false *1

Pinch the connector and disconnect the connector and pipe.

If the connector and the pipe are stuck together, pinch the connector, and then push and pull the pipe to disconnect the pipe and pull it out.

Text in Illustration
*1 Retainer
V100135

Pinch
V100136

Pull

NOTICE:

Do not use any tools in this procedure.



v.

Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.


vi.

To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.



e.
A130944

Observe these precautions when connecting the fuel tube connector (for quick type A).

i.

Check that there is no damage or contamination in the connected part of the pipe.

Text in Illustration
V100135

Push


ii.

Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh spindle oil or gasoline on the tip of the pipe.


iii.
A130945

After having finished the connection, try to pull apart the pipe and the connector to confirm that they are securely connected.

Text in Illustration
V100135

Pull


iv.

Fuel Hose Connector Cover Type:

Attach the lock claw to the connector by pushing down on the cover.


v.

Fuel Pipe Clamp Type:

Install the fuel pipe clamp to the connector.


vi.

Check that there is no fuel leakage.



f.

Observe these precautions when disconnecting the fuel tube connector (for quick type B).

i.
A224877E01
1.962,1.68 2.147,1.831 0.185,0.151 10 *1 2.518,1.768 2.172,1.768 false

Check that there is no damage or foreign matter on the part of the pipe that contacts the connector.

Text in Illustration
*1 Retainer
V100135

Push
V100136

Down
V100137

Pull


ii.
U110359

Detach the 2 claws of the connector retainer. Push down on the connector and disconnect it from the pipe.

Text in Illustration
V100135

Pull
V100136

Push

NOTICE:

Do not use any tools in this procedure.


HINT:

If the connector and pipe are stuck, pinch the fuel pipe by hand, and push and pull the connector to disconnect it.



iii.

Check for foreign matter on the seal surface of the disconnected pipe. Clean it if necessary.


iv.

To protect the disconnected pipe and connector from damage and foreign matter, cover them with a plastic bag.



g.

Observe these precautions when connecting the fuel tube connector (for quick type B).

i.

Check for foreign matter on the pipe and around the connector before connecting it. Clean it if necessary.


ii.
A125397E02
1.857,1.654 2.038,1.841 0.181,0.187 10 *1 2.07,1.741 2.229,1.741 2.229,1.741 2.453,1.561 false

Align the axis of the connector with the axis of the pipe. Push the pipe into the connector, and push up on the retainer.

Text in Illustration
*1 Retainer
V100135

Up
V100136

Push


iii.
A227055

After connecting the pipe and connector, try to pull them apart to confirm that they are securely connected.

Text in Illustration
V100135

Pull



h.

Observe the following precautions when disconnecting the fuel tube connector (for quick type C).

i.

Check for dirt or mud on the fuel tube connector and pipe before disconnection. Clean if necessary.


ii.
A270948E01
2.428,0.257 2.605,0.428 0.178,0.171 10 *1 1.593,0.693 2.197,0.342 2.197,0.342 2.395,0.342 false

Pull the retainer up while pinching it on both sides by hand as shown in the illustration, and disconnect the fuel tube connector from the pipe.

Text in Illustration
*1 Retainer
V100135

Push
V100136

Pull up
V100137

Pull

NOTICE:

Do not use any tools.



iii.
A270949

If the fuel tube connector and pipe are stuck, pinch the fuel pipe by hand and push and pull the connector to disconnect it.

NOTICE:

Do not use any tools.



iv.

Check for dirt or mud on the pipe seal after disconnecting the fuel tube. Clean it if necessary.


v.

Cover the disconnected fuel tube connector and pipe with a plastic bag.

NOTICE:

Do not allow the fuel tube connector or pipe to be damaged or contaminated by foreign matter.




i.

Observe the following precautions when connecting the fuel tube connector (for quick type C).

i.
A270950E01
2.3,0.252 2.477,0.415 0.177,0.163 10 *1 1.692,0.665 2.2,0.34 2.2,0.34 2.264,0.34 false

Align the shaft of the fuel tube connector with the shaft of the pipe, push the fuel tube connector in, and push down the retainer.

Text in Illustration
*1 Retainer
V100135

Connect
V100136

Push down


ii.
A270951

After connecting the fuel tube connector, check that the fuel tube connector and pipe are securely connected by trying to pull them apart.



j.

Observe these precautions when handling the nylon tube.

NOTICE:
·

Be careful not to turn the connection part of the nylon tube and quick connector when connecting them.

·

Do not kink the nylon tube.

·

Do not bend the nylon tube as this may cause blockage.





CHECK FOR FUEL LEAK


a.

Check that there are no fuel leaks after performing maintenance anywhere on the fuel system (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).