Home › Engine / Hybrid System › 1GR-FE (FUEL) › FUEL INJECTOR
RM2660E _51 Engine / Hybrid System _052780 1GR-FE FUEL _0255076 FUEL INJECTOR G

1GR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the injector assembly.


Hide 23250 2.INSPECT INJECTION VOLUME AND LEAKAGE

a.

Check the injector injection.

CAUTION:
·

This test involves high-pressure fuel and electricity.

·

Take every precaution regarding safe handling of both the fuel and the electrical parts.

·

Perform this test in a safe area and avoid any sparks or flame.

·

Do not smoke.



i.
A274079E01
1.198,1.682 1.374,1.838 0.177,0.156 10 *2 0.754,0.795 0.930,0.951 0.177,0.156 10 *1 2.981,1.309 3.158,1.465 0.177,0.156 10 *9 1.465,2.314 1.641,2.470 0.177,0.156 10 *8 2.716,2.249 2.893,2.405 0.177,0.156 10 *7 1.637,1.67 1.814,1.826 0.177,0.156 10 *6 2.989,0.298 3.166,0.454 0.177,0.156 10 *5 3.002,0.896 3.179,1.052 0.177,0.156 10 *4 1.13,0.093 1.307,0.249 0.177,0.156 10 *3 0.732,0.878 0.622,0.878 0.622,0.878 0.539,1.248 false 1.285,1.663 1.285,1.603 1.285,1.603 1.15,1.516 false 2.223,0.259 2.223,0.176 false 2.229,0.176 1.33,0.176 false 1.886,0.446 1.886,0.176 false 2.053,1.757 1.856,1.757 false 2.699,2.336 2.452,2.336 false 2.048,2.395 1.671,2.395 false 2.961,1.395 2.747,1.395 false 2.978,0.979 2.798,0.979 false 2.968,0.386 2.774,0.386 false 2.278,0.803 2.529,0.959 0.251,0.156 10 *10 2.438,0.785 2.438,0.699 2.438,0.699 2.166,0.464 false 1.556,1.273 1.732,1.429 0.177,0.156 10 *3 1.935,1.346 1.766,1.346 false 1.935,0.75 1.846,0.75 false 1.846,0.75 1.846,1.346 false 1.023,0.552 1.200,0.708 0.177,0.156 10 *3 1.248,0.63 1.354,0.63 1.354,0.63 1.425,1.039 false

Assemble SST as shown in the illustration.

SST
09268-31014  (09268-41091, 09268-41120, 09268-41141, 09268-41410, 09268-41500, 09268-41700, 95336-08070)

Text in Illustration
*1 Fuel Pressure Regulator
*2 SST (Union)
*3 SST (Hose Band)
*4 SST (Fuel Tube Connector)
*5 SST (Hose)
*6 SST (Adapter)
*7 SST (Clamp)
*8 Fuel Injector
*9 Fuel Pipe
*10 SST (T-Joint)


ii.

Discharge the fuel system pressure (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


iii.

Disconnect the fuel inlet hose (fuel tube connector) from the fuel pipe.


iv.

Remove the bolt and disconnect the fuel pressure regulator from the fuel delivery pipe.

NOTICE:

Do not disconnect the No. 2 fuel pipe from the fuel pressure regulator.



v.
A274080E01
1.716,0.934 1.900,1.090 0.184,0.156 10 *1 1.716,1.627 1.900,1.783 0.184,0.156 10 *2 1.937,1.017 2.063,1.017 2.063,1.017 2.28,0.914 false 1.922,1.704 2.348,1.704 false

Connect SST to the fuel pipe.

SST
09268-31014  (09268-41500)

Text in Illustration
*1 SST (Fuel Tube Connector)
*2 Fuel Pipe

CAUTION:

Always read the precautions before connecting the fuel tube connector.



vi.
A274081E01
2.464,0.73 2.643,0.900 0.179,0.170 10 *4 1.848,1.587 2.027,1.757 0.179,0.170 10 *3 2.748,0.367 2.927,0.537 0.179,0.170 10 *2 0.794,0.069 0.973,0.238 0.179,0.170 10 *1 0.994,0.155 1.115,0.155 1.115,0.155 1.346,0.377 false 2.447,0.819 2.361,0.819 2.361,0.819 2.257,0.624 false 2.82,0.13 2.82,0.352 false 1.811,1.676 1.533,1.676 false

Connect SST (hose) to the fuel inlet of the pressure regulator with another SST (union) and the 2 bolts.

SST
09268-31014  (09268-41091, 95336-08070)

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

Text in Illustration
*1 Fuel Pressure Regulator
*2 SST (Hose)
*3 No. 2 Fuel Pipe Sub-assembly
*4 SST (Union)


vii.

Connect the fuel return hose to the fuel outlet of the pressure regulator.


viii.
A274082E01
0.118,0.538 0.293,0.707 0.174,0.170 10 *1 0.118,2.583 0.293,2.753 0.174,0.170 10 *4 2.546,0.641 2.720,0.811 0.174,0.170 10 *3 0.118,0.893 0.293,1.063 0.174,0.170 10 *2 2.803,2.411 2.978,2.581 0.174,0.170 10 *6 1.228,2.658 1.402,2.827 0.174,0.170 10 *5 0.201,2.56 0.201,2.457 0.201,2.457 0.574,2.33 false 0.313,0.975 0.564,0.975 false 0.313,0.627 0.606,0.627 false 1.46,2.741 1.772,2.741 false 2.878,2.388 2.878,2.277 2.878,2.277 2.477,2.02 false 2.036,1.026 2.392,0.726 2.392,0.726 2.508,0.726 false

Install a new O-ring to the injector.


ix.

Assemble SST as shown in the illustration.

SST
09268-31014  (09268-41141, 09268-41410, 09268-41700, 95336-08070)

Text in Illustration
*1 SST (Hose)
*2 SST (Hose Band)
*3 O-Ring
*4 SST (Adapter)
*5 Vinyl Tube
*6 SST (Clamp)


x.
A274083E01
2.315,0.913 2.849,1.507 2.849,1.507 2.947,1.507 false 2.145,1.349 2.573,1.787 2.573,1.787 2.661,1.787 false 2.683,1.691 2.865,1.848 0.182,0.158 10 *2 2.973,1.416 3.155,1.573 0.182,0.158 10 *1

Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter).

SST
09268-31014  (09268-41800)

Text in Illustration
*1 Lock
*2 SST (Tie Band)

NOTICE:
·

As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.

·

Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.



HINT:

When removing SST (tie band), disengage the lock.



xi.

Check that SST (clamp) and SST (adapter) cannot be easily separated.


xii.

Install a vinyl tube to the injector.


xiii.

Put the injector into a graduated cylinder.

CAUTION:

Install a suitable vinyl tube to the injector to contain any gasoline spray.



xiv.

Connect the GTS to the DLC3.


xv.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



xvi.

Turn the GTS on.


xvii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Fuel Pump Speed Control.


xviii.
A274084E01
1.817,0.801 2.001,0.964 0.184,0.163 10 *1 1.89,0.349 1.89,0.786 false

Connect SST (EFI inspection wire H) to the injector and the battery for 15 seconds and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times.

SST
09842-30080  

Standard injection volume:

89 to 107 cc (5.4 to 6.5 cu. in.) per 15 seconds


Difference between each injector:

15 cc (0.9 cu. in.) or less


Text in Illustration
*1 SST (EFI Inspection Wire H)
V100135

Connect

NOTICE:
·

Make sure that SST (EFI inspection wire H) is securely connected.

·

Always turn the voltage on and off on the battery side, not the fuel pump side.



If the result is not as specified, replace the injector assembly.



b.

Check for fuel leakage.

i.

In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel leakage from the injector.

Standard fuel leakage:

1 drop or less every 12 minutes


If the fuel leakage is not as specified, replace the injector assembly.