Home › Engine / Hybrid System › 3UR-FE (FUEL) › FUEL INJECTOR
RM2660E _51 Engine / Hybrid System _052781 3UR-FE FUEL _0255087 FUEL INJECTOR G

3UR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the injector assembly.


b.

Inspect the injection volume.

CAUTION:

This test involves high-pressure fuel and electricity. Take all precautions regarding safe handling of both the fuel and the electricity. Perform this test in a safe area, and avoid any sparks or flames. Do not smoke.


i.
C157056E27
0.719,0.458 1.01,0.458 1.01,0.458 1.229,1.188 false 0.573,0.396 0.74,0.583 0.167,0.188 10 false *1

Remove the fuel pipe clamp.

Text in Illustration
*1 Fuel Pipe Clamp


ii.
A088336

Disconnect the fuel tube.

Text in Illustration
V100135

Pinch
V100136

Pull


iii.
A266197E04
2.924,0.812 2.924,1.094 false 1.624,1.331 1.624,1.665 false 0.361,1.459 0.516,0.541 0.516,0.541 0.677,0.541 false 0.714,0.435 0.911,0.614 0.198,0.179 10 *1 0.983,1.561 0.983,1.895 false 2.842,1.12 3.039,1.299 0.198,0.179 10 *4 1.521,1.684 1.719,1.863 0.198,0.179 10 *3 0.903,1.919 1.100,2.098 0.198,0.179 10 *2

Connect SST to the fuel pipe (the vehicle side).

SST
09268-31014  (09268-41500, 09268-41700, 95336-08070)

Text in Illustration
*1 SST (Hose)
*2 SST (Hose Band)
*3 SST (Fuel Tube Connector)
*4 Fuel Pipe


iv.
A266198E04
1.615,0.268 1.401,0.268 false 1.59,0.755 1.386,0.755 false 1.62,1.231 1.192,1.231 false 1.612,2.076 1.262,1.792 1.262,1.792 1.158,1.792 false 1.985,0.11 1.771,0.11 false 1.174,0.175 1.354,0.338 0.180,0.163 10 *2 0.946,1.708 1.127,1.870 0.180,0.163 10 *5 0.973,1.141 1.153,1.304 0.180,0.163 10 *4 1.183,0.668 1.364,0.830 0.180,0.163 10 *3 2.617,1.445 2.797,1.607 0.180,0.163 10 *6 2.013,0.016 2.193,0.179 0.180,0.163 10 *1 2.584,1.532 2.347,1.532 false

Install the O-ring to the fuel injector.


v.

Install SST and the tube to the fuel injector.

SST
09268-31014  (09268-41300, 09268-41600, 09268-41700, 95336-08070)

Text in Illustration
*1 SST (Hose)
*2 SST (Hose Band)
*3 SST (Adapter)
*4 O-ring
*5 Vinyl Tube
*6 SST (Clamp)


vi.
A274395E01
1.756,1.866 1.931,2.029 0.174,0.163 10 *2 2.582,1.498 2.756,1.661 0.174,0.163 10 *1 1.328,1.651 1.676,1.959 1.676,1.959 1.733,1.959 false 1.653,1.294 2.438,1.598 2.438,1.598 2.558,1.598 false

Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter).

SST
09268-31014  (09268-41800)

Text in Illustration
*1 Lock
*2 SST (Tie Band)

NOTICE:
·

As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.

·

Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.



HINT:

When removing SST (tie band), disengage the lock.



vii.

Check that SST (clamp) and SST (adapter) cannot be easily separated.


viii.

Install a vinyl tube to the injector.


ix.
A149193E05
1.633,1.009 1.824,1.196 0.191,0.187 10 *1 1.751,0.371 1.751,0.976 false

Put the injector into a graduated cylinder.

Text in Illustration
*1 SST (Wire)

CAUTION:

Install a strong rubber tube onto the injector to prevent gasoline from splashing.



x.

Operate the fuel pump (turn the engine switch on (IG)).


xi.

Connect SST (wire) to the injector and the battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.

SST
09842-30090  

Standard injection volume:

87 to 105 cm3 (5.3 to 6.4 cu in.) per 15 seconds


Difference between each injector:

18 cm3 (1.1 cu in.) or less


If the injection volume is not as specified, replace the injector assembly.



c.

Check for fuel drop.

i.

In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel drop from the injector.

Standard fuel drop:

1 drop or less in 12 minutes


If the fuel drop is not as specified, replace the injector assembly.