Home › Engine / Hybrid System › 1UR-FE (FUEL) › FUEL INJECTOR
RM2660E _51 Engine / Hybrid System _052782 1UR-FE FUEL _0255097 FUEL INJECTOR G

1UR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the fuel injector assembly.


b.

Inspect the injection volume.

CAUTION:

This test involves high-pressure fuel and electricity. Take all precautions regarding safe handling of both the fuel and the electricity. Perform this test in a safe area and avoid any sparks or flames. Do not smoke.


i.
A266197E04
2.924,0.812 2.924,1.094 false 1.624,1.331 1.624,1.665 false 0.361,1.459 0.516,0.541 0.516,0.541 0.677,0.541 false 0.714,0.435 0.911,0.614 0.198,0.179 10 *1 0.983,1.561 0.983,1.895 false 2.842,1.12 3.039,1.299 0.198,0.179 10 *4 1.521,1.684 1.719,1.863 0.198,0.179 10 *3 0.903,1.919 1.100,2.098 0.198,0.179 10 *2

Connect SST to the fuel pipe.

SST
09268-31014  (09268-41500, 09268-41700, 95336-08070)

Text in Illustration
*1 SST (Hose)
*2 SST (Hose Band)
*3 SST (Fuel Tube Connector)
*4 Fuel Pipe


ii.
A266198E04
1.615,0.268 1.401,0.268 false 1.59,0.755 1.386,0.755 false 1.62,1.231 1.192,1.231 false 1.612,2.076 1.262,1.792 1.262,1.792 1.158,1.792 false 1.985,0.11 1.771,0.11 false 1.174,0.175 1.354,0.338 0.180,0.163 10 *2 0.946,1.708 1.127,1.870 0.180,0.163 10 *5 0.973,1.141 1.153,1.304 0.180,0.163 10 *4 1.183,0.668 1.364,0.830 0.180,0.163 10 *3 2.617,1.445 2.797,1.607 0.180,0.163 10 *6 2.013,0.016 2.193,0.179 0.180,0.163 10 *1 2.584,1.532 2.347,1.532 false

Install the O-ring to the fuel injector.


iii.

Install SST and the tube to the fuel injector.

SST
09268-31014  (09268-41300, 09268-41600, 09268-41700, 95336-08070)

Text in Illustration
*1 SST (Hose)
*2 SST (Hose Band)
*3 SST (Adapter)
*4 O-ring
*5 Vinyl Tube
*6 SST (Clamp)


iv.
A274395E01
1.756,1.866 1.931,2.029 0.174,0.163 10 *2 2.582,1.498 2.756,1.661 0.174,0.163 10 *1 1.328,1.651 1.676,1.959 1.676,1.959 1.733,1.959 false 1.653,1.294 2.438,1.598 2.438,1.598 2.558,1.598 false

Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter).

SST
09268-31014  (09268-41800)

Text in Illustration
*1 Lock
*2 SST (Tie Band)

NOTICE:
·

As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.

·

Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.



HINT:

When removing SST (tie band), disengage the lock.



v.

Check that SST (clamp) and SST (adapter) cannot be easily separated.


vi.

Install a vinyl tube to the injector.


vii.

Put the injector into a graduated cylinder.

CAUTION:

Install a strong rubber tube to the injector to prevent gasoline from splashing.




ix.
A149193E09
1.975,0.46 1.975,0.93 false 1.901,0.947 2.081,1.114 0.180,0.166 10 *1

Connect SST (EFI inspection wire I) to the injector and battery for 15 seconds, and then measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.

SST
09842-30090  

Standard injection volume:

82 to 99 cc (5.0 to 6.0 cu in.) per 15 seconds


Difference between each injector:

17 cc (1.0 cu in.) or less


Text in Illustration
*1 SST (EFI Inspection Wire I)
V100135

Connect

NOTICE:
·

Make sure that SST (EFI inspection wire I) is securely connected.

·

Always turn the voltage on and off on the battery side, not the fuel pump side.



If the injection volume is not as specified, replace the injector assembly.



c.

Check for leakage.

i.

In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel leakage from the injector.

Standard fuel leakage:

1 drop or less in 12 minutes