Home › Engine / Hybrid System › 1VD-FTV (FUEL) › FUEL SYSTEM(w/o DPF)
RM2660E _51 Engine / Hybrid System _052783 1VD-FTV FUEL _0255114 FUEL SYSTEM(w/o DPF) L

1VD-FTV FUEL  FUEL SYSTEM(w/o DPF)  PRECAUTION  


IGNITION SWITCH EXPRESSION


HINT:

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition Switch off LOCK Off
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START Start



FUEL SYSTEM


a.

Observe these precautions when disconnecting the fuel tube connector (for quick type A).

i.
A157617E20
0.594,1.094 0.896,1.26 0.302,0.167 10 false Pull

Detach the lock claw by lifting up the cover, as shown in the illustration.


ii.

Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.


iii.
A088336E62
0.802,0.25 1.177,0.427 0.375,0.177 10 false Pinch 1.74,1.75 2.094,1.958 0.354,0.208 10 true Pinch 0.313,1.729 0.563,2.094 0.25,0.365 10 true Pull

Pinch the connector and disconnect the connector and pipe.

If the connector and the pipe are stuck together, pinch the connector, then push and pull the pipe to disconnect the pipe and pull it out.

NOTICE:

Do not use any tools in this procedure.



iv.

Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.


v.
A099427E11
3.036,2.045 3.414,2.131 0.378,0.086 1.822,0.085 2.731,0.287 0.909,0.202 10 Plastic Bag 1.45,0.905 1.626,0.202 false 1.626,0.202 1.796,0.202 false

To protect the disconnected pipe and connector from damage and contamination, cover it with a plastic bag.



b.

Observe these precautions when disconnecting the fuel tube connector (for quick type B).

i.
A167866E01
1.366,1.665 1.913,1.814 0.547,0.149 10 Retainer 2.507,1.752 2.063,1.752 false

Check that there is no damage or foreign matter on the part of the pipe that contacts the connector.


ii.
U110359

Detach the 2 claws of the connector retainer. Push down on the connector and disconnect it from the pipe.

HINT:

If the connector and pipe are stuck, pinch the fuel pipe by hand, and push and pull the connector to disconnect it.


NOTICE:

Do not use any tools in this procedure.



iii.

Check for foreign matter on the seal surface of the disconnected pipe. Clean it if necessary.


iv.
A103972E02
0.163,0.197 0.881,0.393 0.717,0.196 10 Plastic Bag 1.07,0.332 1.206,0.332 1.206,0.332 1.616,0.678 false

To protect the disconnected pipe and connector from damage and foreign matter, cover it with a plastic bag.



c.

Observe these precautions when connecting the fuel tube connector (for quick type B).

i.
A125397E01
1.351,1.654 1.941,1.841 0.590,0.187 10 Retainer 2.07,1.755 2.229,1.755 2.229,1.755 2.453,1.561 false

Check for foreign matter on the pipe and around the connector before connecting it. Clean it if necessary.


ii.

Align the axis of the connector with the axis of the pipe. Push the pipe into the connector, and push up on the retainer.


iii.
A093435

After connecting the pipe and connector, try to pull them apart to confirm that they are securely connected.



d.
A130944E01
2.381,1.287 2.729,1.444 0.348,0.158 10 Push

Observe these precautions when connecting the fuel tube connector (for quick type A).

i.

Check that there is no damage or contamination in the connected part of the pipe.


ii.

Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh spindle oil or gasoline on the tip of the pipe.


iii.
A130945E02
2.392,1.393 2.659,1.548 0.267,0.155 10 Pull

After having finished the connection, try to pull apart the pipe and the connector to confirm that they are securely connected.


iv.
A157616E12
0.594,1.01 0.948,1.167 0.354,0.156 10 false Push

Attach the lock claw to the connector by pushing down on the cover, as shown in the illustration.


v.

Check that there is no fuel leakage.




CHECK FOR FUEL LEAK


a.

Check that there are no fuel leaks after performing maintenance anywhere on the fuel system (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/o DPF)>ON-VEHICLE INSPECTION).