Home › Engine / Hybrid System › 1VD-FTV (FUEL) › INJECTOR DRIVER › from 2015.08
RM2660E _51 Engine / Hybrid System _052783 1VD-FTV FUEL _0255116 INJECTOR DRIVER A

1VD-FTV FUEL  INJECTOR DRIVER  INSTALLATION  


PROCEDURE

Hide 89871A 1.INSTALL INJECTOR DRIVER

NOTICE:

Be careful not to drop or strike the injector driver.


a.

w/ DPF:

Install the No. 2 injector driver to the No. 2 injector driver bracket with the 4 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


b.

w/o DPF:

Install the No. 2 injector driver and injector driver bracket to the No. 2 injector driver bracket with the 4 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


c.

w/ DPF:

Install the No. 1 injector driver to the No. 1 injector driver bracket with the 4 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


d.

w/o DPF:

Install the No. 1 injector driver and injector driver bracket to the No. 1 injector driver bracket with the 4 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


e.

Install the No. 2 injector driver bracket to the No. 1 injector driver bracket with the 2 bolts.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


f.

w/ DPF:

i.

Install the injector driver assembly with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


ii.

Install the ground wire to the No. 2 injector driver bracket with the bolt.

Torque:
for Type A : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
A418191C01
0.375,0.219 0.688,0.375 0.313,0.156 10 false *A 2.135,0.219 2.448,0.375 0.313,0.156 10 false *B
*A for Type A
*B for Type B


Type A or B can be distinguished by confirming the mark on the bolt.



iii.

Connect the 7 injector driver connectors and attach the 2 wire harness clamps.



g.

w/o DPF:

i.

Install the injector driver assembly with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


ii.

Attach the fuel hose clamp and wire harness clamp.


iii.

Connect the 4 injector driver connectors.


iv.

Install the ground wire to the No. 1 injector driver bracket with the bolt.

Torque:
for Type A : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
A418191C01
0.375,0.219 0.688,0.375 0.313,0.156 10 false *A 2.135,0.219 2.448,0.375 0.313,0.156 10 false *B
*A for Type A
*B for Type B


Type A or B can be distinguished by confirming the mark on the bolt.




Hide 2.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


a.

Connect the cables to the negative (-) main battery and sub-battery terminals.