Home › Engine / Hybrid System › 3UR-FE (INTAKE / EXHAUST) › INTAKE SYSTEM
RM2660E _51 Engine / Hybrid System _052789 3UR-FE INTAKE / EXHAUST _0255165 INTAKE SYSTEM G

3UR-FE INTAKE / EXHAUST  INTAKE SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT INTAKE AIR CONTROL VALVE

a.

Remove the V-bank cover.


b.

Start the engine.


c.

Check that the VSV (for ACIS) is ON (seal) under both of the following conditions:

·

Depressing the accelerator pedal to a achieve throttle valve opening angle of 50° or more.

·

Racing the engine to 4700 rpm or less.


NOTICE:

Do not increase the engine speed to 5400 rpm or more.



d.
A162076E08
1.635,1.656 1.792,1.656 1.792,1.656 1.979,1.469 false 2.115,1.25 2.448,1.25 2.448,1.25 2.448,1.479 false 2.365,1.49 2.573,1.688 0.208,0.198 10 true *a 1.396,1.542 1.635,1.76 0.24,0.219 10 true *b

Check that the VSV (for ACIS) is OFF (vent) under the following conditions:

·

After releasing the accelerator pedal while under the VSV (for ACIS) ON condition.

·

The engine is idling.


Text in Illustration
*a ON (Seal)
*b OFF (Vent)


e.

Connect the intelligent tester to the DLC3.


f.

Perform the Active Test, and then check that the actuator rod operates.

If the result is not as specified, inspect the intake air control valve, vacuum tank and VSV (for ACIS) for normal operation. Replace malfunctioning parts as necessary.


g.

Install the V-bank cover.


Hide 2.CHECK INTAKE AIR CONTROL VALVE OPERATION

a.

Remove the V-bank cover.


b.
A162074E03
1.469,0.085 1.679,0.255 0.210,0.170 10 *1 2.344,0.376 1.996,0.169 1.996,0.169 1.719,0.17 false

Using a 3-way connector, connect a vacuum gauge to the actuator hose.

Text in Illustration
*1 Vacuum Gauge


c.

Start the engine.


d.

While the engine is idling, check that the vacuum gauge indicates 0 kPa (0 mmHg, 0 in.Hg) and the rod is at the OFF position


e.

Fully depress the accelerator pedal quickly. Check that the VSV (for ACIS) turns ON and the rod moves in the ON direction.

NOTICE:

Make sure to fully depress and release the accelerator pedal within 1 second.



f.

Remove the vacuum gauge, and connect the vacuum hose to the actuator.


g.

Install the V-bank cover.


Hide 3.INSPECT INTAKE AIR CONTROL VALVE

a.
A162075E03
1.126,0.06 1.346,0.221 0.220,0.162 10 *1 1.376,0.153 1.706,0.153 1.706,0.153 2.229,0.367 false

Inspect the diaphragm.

i.

Using a vacuum pump, apply a vacuum of 27 kPa (200 mmHg, 7.85 in.Hg). Check that the lever moves.

Text in Illustration
*1 Vacuum Pump

If the result is not as specified, replace the intake air surge tank.



Hide 4.CHECK AIR INDUCTION SYSTEM

HINT:

The illustration shows the areas that may draw in secondary air, which could lead to idling problems.


a.

Check that the hoses are installed correctly.


b.

Check for cracks, etc. in the hoses.

A385913E01
1.885,0.708 1.885,0.229 1.885,0.229 1.708,0.229 false 2.177,0.74 2.177,0.26 2.177,0.26 2.333,0.26 false 3.01,0.781 3.01,0.49 3.01,0.49 3.167,0.49 false 1.708,1.552 2.115,1.552 false 3.292,2.385 3.292,2.219 3.292,2.219 3.781,2.115 false 2.75,4.74 2.458,4.177 2.458,4.177 1.708,4.177 true 1.833,5.104 2.24,5.104 false 3.958,5.354 3.958,6.052 false 4.292,3.802 4.802,1.594 4.802,1.594 4.99,1.594 false 5.885,2.646 5.885,2.885 false 5.375,4.24 5.917,4.24 true 5.646,5.104 5.969,5.104 false 1.51,0.135 1.823,0.333 0.313,0.198 10 false *1 2.375,0.167 2.688,0.365 0.313,0.198 10 false *2 3.24,0.406 3.552,0.604 0.313,0.198 10 false *3 1.51,1.49 1.927,1.781 0.417,0.292 10 false *4 3.229,2.427 3.542,2.625 0.313,0.198 10 false *5 1.49,4.083 1.802,4.281 0.313,0.198 10 false *6 1.615,5.021 1.927,5.219 0.313,0.198 10 false *7 3.875,6.094 4.188,6.292 0.313,0.198 10 false *8 5.063,1.51 5.375,1.708 0.313,0.198 10 false *9 5.781,2.917 6.094,3.115 0.313,0.198 10 false *10 5.969,4.146 6.281,4.344 0.313,0.198 10 false *11 6.031,5.01 6.344,5.208 0.313,0.198 10 false *12

Text in Illustration
*1 Air Cleaner *2 Mass Air Flow Meter
*3 Air Cleaner Hose *4 Resonator
*5 Throttle Body *6 Fuel Pressure Regulator
*7 Ventilation Pipe *8 Intake Manifold
*9 Intake Air Control Valve Actuator (for ACIS) *10 Purge VSV
*11 Vacuum Switching Valve (for ACIS) *12 Ventilation Pipe